Digital Projection E-Vision Laser 6500 Series Manual de usuario

E-Vision Laser 6500 Series

High Brightness Digital Video Projector

Rev B August 2017

117-763B

USER MANUAL

Digital Projection

E-Vision Laser 6500 Series User Manual Rev B August 2017

—i —

This publication, including all photographs, illustrations and software, is protected under international

be reproduced without written consent of the author.

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no

representations or warranties with respect to the contents hereof and specifically disclaims any implied

warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to

revise this publication and to make changes from time to time in the content hereof without obligation of

the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations

and pending applications in other countries throughout the world.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or

registered trademarks of HDMI Licensing LLC in the United States and other

countries.

MHL, the MHL logo, and Mobile High-Definition Link are trademarks or registered

trademarks of MHL licensing, LLC.

HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT

Alliance.

All other product names used in this manual are the properties of their respective owners and are

acknowledged.

Digital Projection

E-Vision Laser 6500 Series User Manual Rev B August 2017

—ii —

Important Safety Information

Important:

It is strongly recommended that you read this section carefully before using the projector. These

safety and usage instructions will ensure that you enjoy many years of safe use of the projector.

Keep this manual for future reference.

Symbols Used

Warning symbols are used on the unit and in this manual to alert you of hazardous situations.

The following styles are used in this manual to alert you to important information.

Note:

Provides additional information on the topic at hand.

Important:

Provides additional information that should not be overlooked.

Caution:

Alerts you to situations that may damage the unit.

Warning:

Alerts you to situations that may damage the unit, create a hazardous environment, or cause

personal injury.

Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this

example:

“Push the Menu button on the remote control to open the Main menu.”

General Safety Information

Do not open the unit case. There are no user-serviceable parts in the unit. For servicing, contact

qualified service personnel.

Follow all warnings and cautions in this manual and on the unit case.

To avoid damage to eyes, do not look into the lens when the light source is on.

Do not place the unit on an unstable surface, cart, or stand.

Avoid using the system near water, in direct sunlight, or near a heating device.

Do not place heavy objects such as books or bags on the unit.

Notice

This product is intended for the adults who have the ability to operate this machine.

Please write down your projector model number and serial number and keep the information for

maintenance purposes in the future. Should the equipment be lost or stolen, the information could also be

used for the police report.

Model number:

Serial number:

Digital Projection

E-Vision Laser 6500 Series User Manual Rev B August 2017

–iii –

LASER WARNING

This symbol indicates that there is a potential hazard of eye exposure to laser

radiation unless the instructions are closely followed.

CLASS 3R LASER PRODUCT

This Laser Product is designated as Class 3R during all procedures of operation. LASER

LIGHT - AVOID DIRECT EYE EXPOSURE.

Do not point laser or allow laser light to be directed or reflected toward other people or

reflective objects .

Direct or scattered light can be hazardous to eyes and skin.

There is a potential hazard of eye exposure to laser radiation if the included instructions are not

followed.

Caution –use of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure

Laser Parameters

Wavelength 450nm - 460nm (Blue)

Mode of operation Pulsed, due to frame rate

Pulse width 1.34ms

Pulse repetition rate 120Hz

Maximum laser energy 0.698mJ

Total internal power >100w

Apparent source size >10mm, at lens stop

Divergence >100 mili Radian

Digital Projection

E-Vision Laser 6500 Series User Manual Rev B August 2017

—iv —

Product labels

Below drawing show the label’s location

1 2

Hazard Warning Symbol

and Aperture Label

Explanatory Label

CAUTION

Possibly hazardous optical radiation emitted

from this product.

Do not stare at operating lamp.

May be harmful to the eyes.

ATTENTION

Ce produit peut émettre des rayonnements

optiques dangereux.

Ne pas fixer la lampe en fonctionnement.

Peut être nocif pour les yeux.

RISK GROUP 2

Explanatory Label

Digital Projection

E-Vision Laser 6500 Series User Manual Rev B August 2017

–v –

Location of laser aperture

Below drawing is the laser aperture location. Be careful not to let the eye see the light directly.

Interlock switches

This machine has 2 (Top cover x 1, Lens x 1) Interlock switches to protect the laser light Leakage.

1. Will power-off the system individually when the top cover is removed.

2. Will power-off the system individually when the lens is removed or not install correctly.

Laser aperture

Digital Projection

E-Vision Laser 6500 Series User Manual Rev B August 2017

—vi —

Projector Installation Notice

There is no limitation angle for projector installation.

Allow at least 50 cm clearance around the exhaust vent.

Ensure that the intake vents do not recycle hot air from the exhaust vent.

When operating the projector in an enclosed space, ensure that the surrounding air temperature

within the enclosure does not exceed operation temperature while the projector is running, and the

air intake and exhaust vents are unobstructed.

All enclosures should pass a certified thermal evaluation to ensure that the projector does not

recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is

with the acceptable operation temperature range.

The projector can be raised or lowered by rotating the adjustable feet. DO NOT attempt to fully

remove the feet.

Minimum 500mm

(19.69 inch)

Minimum 500mm

(19.69 inch)

Minimum 500mm

(19.69 inch)

Minimum 500mm

(19.69 inch)

Minimum 300mm

(11.81 inch)

Minimum 100mm

(3.94 inch)

Minimum 500mm

(19.69 inch)

Minimum 500mm

(19.69 inch)

Digital Projection

E-Vision Laser 6500 Series User Manual Rev B August 2017

–vii –

Verify Installation Location

To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper

grounding and equalized ground potential for all of the equipment in the Projector System.

The power code provided with the Projector should be used. In case of any missing item, other

qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use

2-blade power cord.

Verify if the voltage is stable, grounded properly and there is no electricity leakage.

Measure total power consumption which should not higher the safety capacity and avoid safety

issue and short circuit.

Turn on Altitude Mode when located in high altitude areas

The projector can only be installed upright or inverted.

When installation the bracket, make sure the weight limit is not exceed and firmly secured.

Avoid installing near air conditioner duct or subwoofer.

Avoid installing at high temperature, insufficient cooling and heavy dust locations.

Keep your product away from fluorescent lamps (>1 Meter) to avoid malfunction

caused by IR interference

The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted

tightly, with the screws on both sides securely fastened to ensure proper connection of the signal

wire for achieving optimal display effect.

The AUDIO IN connector should be connected to the AUDIO IN port and CANNOT be connected

to AUDIO OUT or other ports like BNC, RCA; otherwise, it will lead to mute output and even

DAMAGE the port.

Install the projector above 200cm to avoid damage.

The power cord and signal cable should be connected before power on the projector. During the

projector starting and operating process, DO NOT insert or remove the signal cable or the power

cord to avoid damaging the projector.

Cooling notes

Air outlet

Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.

Air outlet location should not be in front of the lens of other projector to avoid causing illusions.

Keep the outlet at least 100cm away from the inlets of other projectors

The projector generates a massive amount of heat during use. The internal fan dissipates the heat

of the projector when shutting down, and such process may continue for a certain period. After the

project enters STANDBY MODE status, press the AC power button to turn off the projector and

remove the power cord. DO NOT remove the power cord during the shutdown process, as it may

cause damage to the projector. In the meantime, the delayed heat radiating will also affect the

service life of the projector. The shutdown process may vary depending on the model used.

Whatever the case may be, be sure to disconnect the power cord till after the projector enters the

STANDBY status.

Air inlet

Make sure there is no object blocking air input within 30 cm.

Keep the inlet away from other heat sources

Avoided heavy dust area

Digital Projection

E-Vision Laser 6500 Series User Manual Rev B August 2017

—viii —

Power Safety

Only use the supplied power cord.

Do not place anything on the power cord. Place the power cord where it will not be in the way of

foot traffic.

Remove the batteries from the remote control when storing or not in use for a prolonged period.

Cleaning the Projector

Unplug the power cord before cleaning. See Cleaning the Projector page 56.

Allow the light source to cool for about one hour.

Regulatory Warnings

Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on

page 73.

Symbol Explanations

DISPOSAL: Do not use household or municipal waste collection services for

disposal of electrical and electronic equipment. EU countries require the use

of separate recycling collection services.

Special Care for Laser Beams!

Special care should be considered when DLP projectors and high power laser equipment are used in the

same room as.

Direct or indirect hit of a laser beam on to the projector lens can severely damage the Digital Mirror

Devices (DMD™).

Sunlight Warning

Avoid using the E-Vision Laser 6500 Series in direct sunlight.

Sunlight on the projector lens can severely damage the Digital Mirror Devices (DMD™).

Digital Projection

E-Vision Laser 6500 Series User Manual Rev B August 2017

–ix –

Main Features

Compatible with all major video standards including NTSC, PAL, and SECAM.

A high brightness rating allows for presentations in daylight or in lit rooms.

Flexible setup allows for front, rear projections.

Line-of-vision projections remain square, with advanced keystone correction for angled

projections.

Input source automatically detected.

High brightness for projection in just about any environment.

Supports resolutions up to WUXGA for clear and crisp images.

DLP® and BrilliantColor™ technologies from Texas Instruments.

Centered lens for easy installation.

Horizontal and vertical lens shift.

MHL device compatibility for streaming of video and audio content from a compatible

mobile device.

Built-in speaker with multiple audio-in and audio-out ports.

Network ready for integration and system administration via RJ45.

Sealed engine to minimizing the impact of dust and smoke.

Anti-theft security features include: Kensington security slot, security bar.

Built-in HDBaseT receiver. HDBaseT™ interface with support for distribution of HD video

and digital audio content over standard CAT5e/6 LAN cable

Advanced laser phosphor light engine for superior brightness and color uniformity

Laser design deliveries up to 20,000 hours of operational time

About this Manual

This manual is intended for end users and describes how to install and operate the DLP projector.

Wherever possible, relevant information—such as an illustration and its description—has been kept on

one page. This printer-friendly format is both for your convenience and to help save paper, thereby

protecting the environment. It is suggested that you only print sections that are relevant to your needs.

Tabla de contenidos

Otros manuales de Proyector de Digital Projection

Digital Projection

Digital Projection E-Vision Laser 13000 WU Series Hoja de datos

Digital Projection

Digital Projection E-Vision Laser 15000 Series Hoja de datos

Digital Projection

Digital Projection Titan 800 Manual de usuario

Digital Projection

Digital Projection HIGHlite Laser 3D Series Manual de usuario

Digital Projection

Digital Projection Titan series Instrucciones de instalación y funcionamiento

Digital Projection

Digital Projection SHOWlite 6000gv Manual de usuario

Digital Projection

Digital Projection TITAN sx+600 Manual de usuario

Digital Projection

Digital Projection LIGHTNING 35HD Manual de usuario

Digital Projection

Digital Projection LIGHTNING 30-1080p Manual de usuario

Digital Projection

Digital Projection Insight Laser 4K Manual de usuario

Digital Projection

Digital Projection TheaterScope System Manual de usuario

Digital Projection

Digital Projection HIGHlite Laser 3D Series Manual de usuario

Digital Projection

Digital Projection TITAN Quad 1080p-3D Manual de usuario

Digital Projection

Digital Projection HIGHlite 4100gv Manual de usuario

Digital Projection

Digital Projection 40HD-T Manual de usuario

Digital Projection

Digital Projection E-Vision 6900 Series Manual de usuario

Digital Projection

Digital Projection HIGHlite 740 Series Manual de usuario

Digital Projection

Digital Projection Titan 930 Manual de usuario

Digital Projection

Digital Projection LIGHTNING 30sx+c Manual de usuario

Digital Projection

Digital Projection INSIGHT 4K Dual LED Series Manual de funcionamiento

Digital Projection

Digital Projection THUNDER 10000Dsx Manual de usuario

Digital Projection

Digital Projection HIGHlite 660 3D Series Manual de funcionamiento

Digital Projection

Digital Projection 119-712B Manual de usuario

Digital Projection

Digital Projection TITAN sx+-330-3D L or P Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario