Digital Equipment DIGITAL MultiSwitch 600 System Manual de usuario

EK-DLSSM-QS. A01

DIGITAL MultiSwitch 600 System

Quick Start

January 1997

This card explains how to install and configure a DIGITAL MultiSwitch 600 Stack System. You

need the following items to install this product:

For detailed instructions and important safety information, see the DIGITAL MultiSwitch 600

System Installation and Configuration manual.

Installing a DIGITAL MultiSwitch 600 System

This section summarizes the procedures for installing and starting the DIGITAL MultiSwitch 600

System. Follow these procedures, in order, to install and start up the DIGITAL MultiSwitch 600.

Procedure 1: Plan the Installation

Read chapter 1 of the DIGITAL MultiSwitch 600 System Installation and Configuration manual to

understand DIGITAL MultiSwitch 600 System concepts. Plan your installation according to the

following criteria:

•DIGITAL MultiSwitch 600 Stack

Station

•DIGITAL MultiSwitch 600 Stack

Director

•Setup port device (PC or terminal)

•Setup port cable and (optionally) an adapter

•IP address, subnet mask, and gateway address

(for Stack Director)

If Then

The stack will be managed You need one Stack Director. The Stack Director

must be at the bottom of the stack.

The stack will be rack mounted You must use the mounting tray.

The stack will have more than one level Using the mounting tray is recommended.

The stack will use modular options Install modular options before powering up the

stack.

Procedure 2: Install the First Module of a DIGITAL MultiSwitch 600 Stack

Note: Steps 2 through 5 apply only if the stack has more than one level. If the stack

has just one level (for example, a Stack Director and no Stack Stations), keep the dust

cap on.

Procedure 3: Install Any Additional Levels of the Stack

Step Action

1Align the holes on the underside of the Stack Director with the mounting holes on

the tray. Turn the Stack Director or Stack Station upside down and attach the

mounting tray to it using the supplied screws.

2Remove the dust cap from the vertical connector on the Stack Director.

3Insert the Stack Interconnect Card into the vertical connector. Align the notches in

the card with the corresponding key in the connector.

4Press down on the Stack Interconnect Card until it is fully seated.

5Insert and tighten wing nuts. Install alignment pylons if they are not already

installed.

6Attach a functional module to the Stack Director.

Step Action

1On the previously installed level, align the wings of the wing nuts within the wing

guide on the installed Stack Station.

2Remove the two wing nuts from the next Stack Station.

3If it is present, remove the mounting plug from the bottom of the next Stack Station

by turning it clockwise 1/4 turn.

4Seat the next Stack Station on the installed Stack Director or Stack Station while

aligning the pylons and wing nuts.

5Press down on the corner of the Stack Station until it snaps into place.

6Insert and finger tighten two wing nuts to the Stack Station. Align the wings on the

wing nuts within the wing guide on the Stack Station.

7Attach a functional module to the Stack Station.

8To continue adding levels to the stack, repeat steps 1 through 7.

Note: The top Stack Station should have the dust cap on its vertical connector.

Procedure 4: Cable the Stack Director and Stack Station

Procedure 5: Connect Power

Step Action

1Select the appropriate cable, and if necessary, an adapter to connect a setup port

device (terminal or PC) to the setup port. Normally, this is a BN24H-xx cable and

an H8571-J or H8585-A adapter. Connect the setup port device to the setup port on

the Stack Director.

2Configure the setup port device (terminal or PC) as follows: 9600 baud, 8 bits, no

parity, 1 stop bit.

3If youare using out-of-bandmanagement, connect a modem or access service tothe

Stack Director OBM port using a 9-pin D-sub connector.

4To extend the internal 10base2 LAN, connect to the Stack Director 10Base2 port

using a 10Base2 cable with a BNC connector. If you do not use this port, then you

MUST attach a 50-ohm terminator (H8225).

5If you are redirecting the Management MAC, connect to the Stack Director

Management Access Port using a straight-through cable with an 8-pin MJ port

connector.

Note: You cannot simultaneously use the 10Base2 and the Management Access

ports for in-band management. The Management Access Port has precedence for

SNMP management traffic; however the 10Base2 data network will still be active.

Step Action

1Connect the supplied AC line cord to the IEC power connector on each Stack

Station. Then, connect each AC line cord into an AC outlet or power strip.

WARNING: Always make sure this unit is adequately grounded. Do not connect

more than five Stack Stations into a single power strip unless the power strip is

protected by a GFCI device.

2Connect an AC line cord into the IEC power connector of the Stack Director (at the

bottom of the stack) and into an AC outlet or power strip.

3Make sure that the Power OK LEDs on all Stack Stations and the Stack Director are

on.

Procedure 6: Assign an IP Address to Stack Director

clearVISN, DEChub, DIGITAL, and the DIGITAL logo are trademarks of Digital Equipment Corporation.

Step Action

1Press Return on the setup port device until the Digital MultiSwitch 600

Installation Menu appears.

2Select option [4] Configure IP to display the IP CONFIGURATION MENU.

3Select [4] Set In-Band Interface IP Address to display the IN-

BAND INTERFACE IP ADDRESS CONFIGURATION menu.

4Enter the in-band interfaceIP address, subnet mask, and gateway address, and press

<Return> until the console displays the IP CONFIGURATION MENU.

5If you are using out-of-band management, select [5] Set Out-of-Band

Interface IP Address to display the Out-of-Band ADDRESS

CONFIGURATION menu.

6Enter the out-of-band address, if needed. This must not be the same address as the

in-band address.

Tabla de contenidos

Otros manuales de Cambiar de Digital Equipment

Digital Equipment

Digital Equipment DIGITAL MultiSwitch 612EX Manual de usuario

Digital Equipment

Digital Equipment DECmau 900TL Manual de usuario

Digital Equipment

Digital Equipment EtherWORKS Switch 6T/2TX Manual de usuario

Digital Equipment

Digital Equipment VNswitch 900EE Instrucciones de funcionamiento y mantenimiento

Digital Equipment

Digital Equipment GIGAswitch Manual del propietario

Digital Equipment

Digital Equipment MultiSwitch 700 Manual de usuario

Digital Equipment

Digital Equipment 624T Manual de instrucciones

Digital Equipment

Digital Equipment DEChub ONE Manual de usuario

Digital Equipment

Digital Equipment EtherWORKS Switch 8T/TX Instrucciones de funcionamiento y mantenimiento

Digital Equipment

Digital Equipment VNswitch 900EF Instrucciones de funcionamiento y mantenimiento

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario