Digital Equipment DECmpp 12000/Sx 100 Manual de usuario

DECmpp12000/SxModel100

HardwareServiceManual

Part Number: EK–DECAC–SM. C01

September 1992

This document provides service and diagnostic procedures for DECmpp

12000/Sx and DECmpp 12000–LC/Sx Series systems.

Revision/Update Information: This document has been revised for

DECmpp Version 1.1.

Operating System and Version: ULTRIX Version 4.2A.

Future releases may require higher

versions.

Software Version: DECmpp 12000/Sx Version 1.1.

Digital Equipment Corporation

Maynard, Massachusetts

First Printing, January 1992

Revised, September 1992

The information in this document is subject to change without notice and should not be construed

as a commitment by Digital Equipment Corporation. Digital Equipment Corporation assumes no

responsibility for any errors that may appear in this document.

The software described in this document is furnished under a license and may be used or copied

only in accordance with the terms of such license.

NOTICE—Class A Computing Device:

This equipment generates, uses, and may emit radio frequency energy. The equipment has been

type tested and found to comply with the limits for a Class A computing device pursuant to Subpart

J or Part 15 of FCC rules, which are designed to provide reasonable protection against such radio

frequency interference when operated in a commercial environment. Operation of this equipment in

a residential area may cause interference; in which case, measures taken to correct the interference

are at the user’s expense.

Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions

as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software

clause at DFARS 252.227-7013.

The postpaid Reader’s Comments forms at the end of this document request your critical evaluation

to assist in preparing future documentation.

The following are trademarks of Digital Equipment Corporation: DECnet, DECstation, DECsupport,

DECsystem, DECwindows, Rdb/VMS, ThinWire, TURBOchannel, ULTRIX, VAX, VAX DOCUMENT,

VMS, and the DIGITAL logo.

The following are registered trademarks of the MasPar Computer Corporation: MasPar and

the MasPar logo. The following are trademarks of the MasPar Computer Corporation: MasPar

Data Display Library (MPDDL), MasPar FORTRAN (MPF), MasPar Input/Output Channel,

MasPar Parallel Application Language (MPL), MasPar Parallel Disk Array (MPDA), and MasPar

Programming Environment (MPPE). UNIX is a registered trademark of UNIX System Laboratories,

Inc.

This document was prepared using VAX DOCUMENT, Version 2.0.

Contents

Preface ............................................................ vii

1 System Overview

1.1 Turning the System On and Off . ................................ 1–4

1.1.1 Powerup Sequence ........................................ 1–6

1.1.2 Powerdown Sequence ...................................... 1–6

2 DPU Controls and Indicators

2.1 Overview of Controls and Indicators ............................. 2–5

2.2 DPU Power System . . ........................................ 2–5

2.3 Indicators . . ................................................ 2–7

2.3.1 Front Panel Indicators ..................................... 2–7

2.3.2 Service Indicators ........................................ 2–7

2.3.2.1 Power Tray Indicators . . ................................ 2–9

2.3.2.2 Array Control Unit PCB Indicators . ....................... 2–10

2.3.2.3 PE Array and Router PCB Indicators ...................... 2–12

2.3.2.4 PVME Indicators ...................................... 2–13

3 Checking and Adjusting DPU Power Supply

3.1 Voltage Measurements and Adjustments . . . ....................... 3–3

4 Cables, Connectors, and Auxiliary PCBs

4.1 Cables and Connectors ........................................ 4–1

4.2 Auxiliary PCBs ............................................. 4–2

5 Using Diagnostic Software

5.1 Diagnostic Environment....................................... 5–2

5.1.1 Running the Diagnostics . . . ................................ 5–2

5.1.2 Suspending a Diagnostic Program ............................ 5–2

5.2 Types of Tests............................................... 5–3

5.2.1 Test Suites .............................................. 5–3

5.2.1.1 The acu_diag Test Suite . ................................ 5–3

5.2.1.2 The pe_diag Test Suite . . ................................ 5–3

5.2.2 Test Descriptions . ........................................ 5–4

5.3 Interpreting Log File Messages . ................................ 5–7

5.3.1 The ./LOG File . . . ........................................ 5–8

5.3.2 The /usr/adm/dpujobmgr.log File ............................. 5–10

5.3.3 The /etc/uerf File . ........................................ 5–12

iii

6 Removal and Replacement Procedures

6.1 Card Cage Access ............................................ 6–1

6.2 DPU Card Cage Slots......................................... 6–4

6.2.1 I/O Slots ................................................ 6–4

6.2.2 PE Array PCB Slots . . . .................................... 6–4

6.3 Replacing DPU Card Cage PCBs ................................ 6–6

6.3.1 Replacing the Array Control Unit PCB ........................ 6–6

6.3.2 Replacing Front-End VME Interface PCB . . . ................... 6–9

6.3.3 Replacing PE Array and Router PCBs ......................... 6–10

6.4 Replacing DPU Power Trays ................................... 6–11

6.4.1 Removing the DECmpp 12000/Sx Power Tray ................... 6–11

6.4.2 Installing the DECmpp 12000/Sx Power Tray ................... 6–13

6.4.3 Removing the DECmpp 12000–LC/Sx Power Tray ................ 6–14

6.4.4 Installing the DECmpp 12000–LC/Sx Power Tray ................ 6–15

6.5 Replacing the DECmpp 12000/Sx DPU Fan Tray. ................... 6–18

6.6 Replacing the DECmpp 12000–LC/Sx DPU Fan Tray ................ 6–19

6.7 Removing and Replacing the Lightpipe PCB ....................... 6–20

6.7.1 DECmpp 12000/Sx Lightpipe ................................ 6–20

6.7.2 DECmpp 12000–LC/Sx Lightpipe. ............................ 6–21

7 Backplane Jumpers and Upgrading PE Arrays

7.1 DPU Backplane Jumpers . . .................................... 7–1

7.1.1 Backplane Access ......................................... 7–3

7.1.2 ACU, VMEbus, and I/O Jumpers . ............................ 7–4

7.1.3 X-Net Jumpers ........................................... 7–5

7.2 System Issues for Upgrades .................................... 7–7

7.3 Adding Processor Element Array PCBs ........................... 7–8

7.4 Reconﬁguring Processor Element Array PCBs . . . ................... 7–9

A Recommended Spares List

B Data Parallel Unit Reference Pages

acu_ppdma(1) . . . ............................................ B–2

mpconﬁg(1)................................................. B–3

mpi(1). .................................................... B–4

mpq(1) .................................................... B–5

mpstat(1) .................................................. B–6

pe_arith(1) ................................................. B–8

pe_ckonet(1) ................................................ B–9

pe_diag(1).................................................. B–10

pe_func(1).................................................. B–12

pe_macro(1) ................................................ B–13

pe_memdiag(1) . . ............................................ B–59

pe_rtbp(1).................................................. B–60

pe_rtdiag(1) ................................................ B–62

pe_rtr(1) ................................................... B–63

pe_scan(1) ................................................. B–64

dpumanager(8) . . ............................................ B–65

mpshutdown(8) . ............................................ B–68

Index

Figures

1–1 Typical DECmpp 12000/Sx Installation with DECsystem 5900

Server . ................................................ 1–2

1–2 Typical DECmpp 12000/Sx Installation with DECstation 5000/240

Server . ................................................ 1–2

1–3 Typical DECmpp 12000–LC/Sx Installation ..................... 1–3

1–4 DECsystem 5900 Power Switch .............................. 1–5

1–5 DECstation 5000 Power Switch .............................. 1–5

2–1 DECmpp 12000/Sx DPU Front Controls and Indicators ............ 2–2

2–2 DECmpp 12000-LC/Sx DPU Front Controls and Indicators . . ....... 2–3

2–3 DPU Front Controls ....................................... 2–3

2–4 DPU Rear Controls and Indicators ........................... 2–4

2–5 PCB Service Indicator Locations ............................. 2–8

2–6 Power Tray Service Indicators ............................... 2–9

2–7 Array Control Unit PCB Indicators ........................... 2–10

2–8 PE and Router PCB Indicators .............................. 2–12

2–9 PVME Signal Indicators.................................... 2–13

3–1 DPU Backplane Voltage Test Points ........................... 3–2

3–2 DECmpp 12000 Power Supply Wiring and Voltage Adjustments .... 3–4

3–3 DECmpp 12000–LC HC Power Supply and Voltage Adjustments .... 3–5

3–4 DECmpp 12000–LC Powertec Power Supply and Voltage Adjustments

....................................................... 3–5

4–1 DPU-Server Cables ....................................... 4–2

6–1 DECmpp 12000/Sx Card Cage Access . . ....................... 6–2

6–2 DECmpp 12000–LC/Sx Card Cage Access ...................... 6–3

6–3 DPU Card Cage Slots...................................... 6–5

6–4 PCB Ejector Levers ....................................... 6–7

6–5 ACU Jumpers . . . ........................................ 6–8

6–6 DECmpp 12000 DPU Power Tray Rear . ....................... 6–12

6–7 DECmpp 12000 DPU Power Tray Front ....................... 6–12

6–8 Powertec Power Supply .................................... 6–16

6–9 HC Power Supply. ........................................ 6–17

6–10 Removing the DECmpp 12000–LC Enclosure Top . ............... 6–22

6–11 Replacing the Lightpipe PCB ................................ 6–22

7–1 DPU Card Cage Slots...................................... 7–2

7–2 DECmpp 12000–LC/Sx Front Doors ........................... 7–3

7–3 DPU Backplane Jumpers . . . ................................ 7–4

7–4 DECmpp 12000–LC/Sx X-Net Jumper Conﬁgurations ............. 7–5

7–5 DECmpp 12000/Sx X-Net Jumper Conﬁgurations . ............... 7–6

Tables

1Related Documents . . . .................................... viii

1–1 DPU Power Settings . . .................................... 1–4

2–1 Front Panel Indicators . .................................... 2–7

2–2 Power Tray Service Indicators . . . ............................ 2–9

2–3 ACU Indicators .......................................... 2–11

2–4 PE Array and Router Indicators . ............................ 2–12

2–5 PVME Indicator Descriptions................................ 2–14

5–1 FLTCOD Values .......................................... 5–7

6–1 ACU Jumper Settings . .................................... 6–8

6–2 Powertec Power Supply Wiring . . ............................ 6–16

6–3 HC Power Supply Wiring ................................... 6–17

A–1 DECmpp 12000/Sx Data Parallel Unit RSL . . ................... A–1

Preface

This manual provides service and diagnostic procedures for DECmpp 12000/Sx

systems. Anyone who services DECmpp 12000/Sx Series systems or needs to

replace any items should read this manual and be familiar with the procedures.

Intended Audience

This guide is for use by Digital Services personnel and by self-maintenance

customers who will be servicing the DECmpp 12000 and DECmpp 12000–LC

systems.

Document Structure

The DECmpp 12000/Sx Hardware Service Manual contains seven chapters and

two appendixes.

• Chapter 1 is a system overview and contains the power-up and power-down

routines for both the data parallel unit (DPU) and the front-end server.

• Chapter 2 describes the DPU switches, controls, indicators, and the DPU

power system.

• Chapter 3 describes the DPU power supply settings and how to adjust them,

if necessary.

• Chapter 4 describes the DECmpp 12000/Sx system cables, connectors, and the

printed circuit boards (PCBs) outside the DPU card cage.

• Chapter 5 describes the diagnostic software provided, how to use it, and how

to interpret the results.

• Chapter 6 explains the procedures for removing and replacing the DPU

components.

• Chapter 7 explains the procedures for upgrading the DECmpp 12000/Sx

Series systems by adding more processor element (PE) array PCBs.

• Appendix A lists all of the recommended spare parts for the DPU.

• Appendix B is a collection of Reference Pages that apply to the DPU.

vii

Related Documents

Table 1 lists documents that provide additional information about the DECmpp

12000/Sx system.

Table 1 Related Documents

Document Title Order Number

DECmpp 12000/Sx System Overview Manual AA-PMAPB-TE

DECmpp 12000/Sx System Administration Guide AA-PKU3C-TE

DECmpp 12000/Sx Architecture Speciﬁcation AA-PMASB-TE

DECmpp 12000/Sx Parallel Disk Array Reference Manual EK-DECAB-RM

DECmpp 12000/Sx Parallel VME Reference Manual EK-DECAB-PM

DECmpp 12000/Sx Hardware Installation Guide EK-DECAC-IG

DECstation 5000/240 User Documentation Kit EK-PM380-DK

DECstation 5000/240 Maintenance Guide EK-PM38C-MG

DECstation 5000/240 Pocket Service Guide EK-PM38D-PG

DECsystem 5900 Site Preparation Guide EK-D590A-SP

DECsystem 5900 Installation Guide EK-D590A-IN

DECsystem 5900 Owner’s Guide EK-D590A-OG

DECsystem 5900 Pocket Service Guide EK-D590A-PS

DECsystem 5900 Enclosure Maintenance Manual EK-D590A-EN

DWTVX-Ax VME I/O Subsystem Pocket Service Guide EK-DWTVX-PS

T6000 Module Installation/Owner’s Card EK-T6000-IN

viii

Conventions

The following conventions are used throughout the DECmpp 12000/Sx

documentation set:

Convention Meaning

Return In examples, a key name shown within a box indicates that

you press a key on the keyboard. In text, a key name is not

enclosed in a box but is printed with an initial capital letter,

like Return.

Ctrl/xA key combination, shown with a slash separating the two key

names, indicates that you hold down the ﬁrst key while you

press the second key.

MB1, MB2, MB3 The buttons on a mouse. MB1 is the left button, MB2 is the

center button, and MB3 is the right button of a mouse whose

button arrangement is right-handed. It is possible to redeﬁne

the mouse buttons.

% A percent sign (%) represents the default user prompt for your

system.

# A number sign (#) represents the default superuser (root)

prompt for your system.

...

In examples, a horizontal series of dots, or ellipsis, indicates

that additional parameters, values, or other information can be

entered.

.In examples, a vertical series of dots, or vertical ellipsis,

indicates that a portion of the example is intentionally omitted.

[] In syntax descriptions and functional descriptions, brackets

indicate optional items.

dpumanager(6)

Cross-references to the ULTRIX Reference Pages, which include

the appropriate section number in parentheses.

italicized text In examples, italicized text denotes parameters, values, or

other information that will change from either session to

session or user to user. In text, italicized words or phrases are

used to add emphasis to important words, concepts, or titles of

manuals.

ULTRIX keywords

This typeface is used to indicate system output or the exact

name of a command, option, partition, pathname, directory, or

ﬁle.

Code examples

This typeface is used to display program coding examples.

UPPERCASE and

lowercase strings The ULTRIX system differentiates between lowercase and

uppercase characters. Literal strings that appear in text,

examples, syntax descriptions, and function descriptions must

be entered exactly as shown.

Both the DECmpp 12000/Sx and DECmpp 12000–LC/Sx Series hardware systems

are described in this manual. However, because the two systems are very similar,

references to the DECmpp 12000 system also apply to the DECmpp 12000–LC

system, unless speciﬁc differences between the two systems are noted.

Three types of notes are used in this manual:

•Note

Gives additional information or information particularly important to the

procedure.

•Caution

Indicates potential damage to equipment or data.

•Warning

Indicates potential injury to a person.

Tabla de contenidos

Otros manuales de Servidor de Digital Equipment

Digital Equipment

Digital Equipment AlphaServer 4000 Manual de usuario

Digital Equipment

Digital Equipment DECserver 900MC Instrucciones de funcionamiento y mantenimiento

Digital Equipment

Digital Equipment MicroVAX 3500 Manual de usuario

Digital Equipment

Digital Equipment Prioris Series Manual de usuario

Digital Equipment

Digital Equipment PRIORIS MTE Manual de usuario

Digital Equipment

Digital Equipment MicroVAX 3600 Manual de instrucciones

Digital Equipment

Digital Equipment MUXserver 100 Manual de usuario

Digital Equipment

Digital Equipment Server 3100 series Manual de usuario

Digital Equipment

Digital Equipment 5220 Series Manual de usuario

Digital Equipment

Digital Equipment 5300 Manual de lista de piezas

Digital Equipment

Digital Equipment DEC 3000 Instrucciones de funcionamiento e instalación

Digital Equipment

Digital Equipment VAX 6000-400 Manual de usuario

Digital Equipment

Digital Equipment DECserver 200 Manual de usuario

Digital Equipment

Digital Equipment PRIORIS XL Manual de usuario

Digital Equipment

Digital Equipment AlphaServer 1000 Manual de usuario

Digital Equipment

Digital Equipment PRIORIS ZX MP5 Manual de usuario

Digital Equipment

Digital Equipment Prioris XL 5166 Manual de usuario

Digital Equipment

Digital Equipment DECserver 300 Manual

Digital Equipment

Digital Equipment PRIORIS ZX 5000 MP Manual de usuario

Digital Equipment

Digital Equipment 3100R Series Manual de usuario

Digital Equipment

Digital Equipment AlphaServer 2000 Manual de usuario

Digital Equipment

Digital Equipment DECserver 300 Hoja de instrucciones

Digital Equipment

Digital Equipment 3300R Manual de usuario

Digital Equipment

Digital Equipment VAX 4000 300 Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario