Digikeijs DR5033 Manual de usuario

DR5033 DIGIBOOST

P 1

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

DR5033

DIGIBOOST

instrucon manual

(2021-07-06)

rights reserved. No informaon, images or any part of

this document may be copied without the prior wrien

permission of Digikeijs.

DR5033 DIGIBOOST

P 2

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

1Index

1.0 General informaon 2

1.1 Index 2

1.2 Warranty and warranty condions 3

1.3 Legal informaon 3

2.0 Product overview 4

2.1 General product informaon 4

2.2 Technical Specicaons 4

2.3 Hardware Overview 5

3.0 Adjusng the DR5033 Conguraon 6

3.1 LocoNet® Variables (LNCV) Table 7

3.2 Descripon Conguraon LNCV 3 7

4.0 Connecon examples 8

4.1 Important instrucons for using the DR5033. 8

4.2 Tested central units and connecon types 9

4.3 DR5000, DR5033 Boosters and Feedback

DR4088 modules 11

4.4 DR5000, DR5033 Boosters and Feedback Modules

DR5088RC 12

4.5 DR5000, DR5033 Booster and feedback modules

DR4088xx 13

4.6 Roco® z21®, z21Start®, DR5033 Connecon via

the R-Bus® 14

4.7 Roco® Z21®, DR5033 Connecon via R-Bus® 15

4.8 Lenz Central®, DR5033 via CDE connecon 16

4.9 Uhlenbrock Intellibox®, DR5033 Connecon via

LocoNet® B 17

4.10 Various control panels and snier input of the

DR5033 18

1.0 General Informaon

DR5033 DIGIBOOST

P 3

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

1.2 Warranty and warranty condions

All our products have a 24-month manufacturer's warranty. Please read this manual carefully.

Damage to the product caused by non-compliance with these instrucons will void the warranty.

ATTENTION: The warranty is void if the housing of the product is opened.

1.3 Legal informaon

Prinng errors and mistakes, technical or other changes as well as changes in the availability of individual products are expressly reserved.

Data and illustraons are non-binding. All changes to hardware, rmware and soware are reserved.

We reserve the right to change the design of the product, the soware and / or the rmware without prior noce.

All Digikeijs manuals and other wrien instrucons supplied and/or downloadable are copyrighted.

Reproducon is not permied without the wrien permission of Digikeijs.

DR5033 DIGIBOOST

P 4

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

2.0 product overview

2.1 General product informaon

The DR5033 is a pure DCC booster capable of Railcom®. All other protocols (e.g. Märklin® Mfx®) are not supported!

The DR5033 is an H-bridge booster with various connecon opons (CDE booster connecon, LocoNet® B, Roco® booster bus, track snier) to connect the

DR5033 to an exisng central. The conguraon of the DR5033 can be customized via LNCV programming. The DR5033 can be congured to switch the polarity

of the track output automacally or by magnec command. The DR5033 can be switched on and o separately via a magnec command and the current status

can be queried by the control panel.

Important! The DR5033 must not be used in systems that operate according to the common ground principle. This can lead to the destrucon of the booster

and/or the central unit.

2.2 Technical specicaons

The terminals are designed for a cross-secon of 0.75mm².

outputs loading capacity inputs power supply

DR5033 Track Out

3A LocoNet® B

Track Snier

Roco® Booster Bus

15-19V DC

DR5033 DIGIBOOST

P 5

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

2.3 Hardware Overview

1CDE Booster connecon

(Please check whether the CDE connecon of your control panel com-

plies with the requirements specied by Lenz®).

2LocoNet® B Connector 1

3LocoNet® B Connector 2

4Tack Snier Input

By connecng the Track Snier input to the track output of the central unit, the track

signal is recognized even if none of the other input opons are available.

(CDE Booster connecon, LocoNet® B, Roco® B Bus) can be used on the DR5033.

5Roco® Booster Bus Connector 1

6Roco® Booster Bus Connector 2

7power supply

DC 15-19V 3,5A

8Track Output

9Booster Status LED

Track signal present (normal operaon)

No track signal present.

(Loconet® B, B-Bus, CDE, Track Snier Input)

Booster load under 90%.

(LED becomes brighter under load)

Booster load greater than 90%.

Short circuit detected

Stop command detected (e.g. by the control unit)

Track Out reversed polarity.

Note: If the blue LED lights up when driving over the booster separaon

points, the track output of the DR5033 is connected with reversed polarity.

DR5033 DIGIBOOST

P 6

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

3.0 Adjusng the DR5033 Conguraon

The DR5033 is a DCC booster whose sengs (LocoNet® module address, magnec arcle address, etc.) can be easily adjusted via LNCV programming. With the

LNCV 3, the behaviour (short-circuit behaviour, start behaviour, automac polarity reversal, etc.) of the booster can be adapted.

1. Connect the DR5033 to the LocoNet B port on the DR5000.

(Important! if LocoNet® module addresses are idencal or if the LocoNet® module address is un-

known, only one DR5033 may be plugged into the LocoNet®.)

2. Connect the DR5033 to the power supply.

3. Call the "LNCV Programming" programming menu of the DR5000 under Loconet B.

4. Select the DR5033 from the list or enter its product number numerically.

5. Read out or enter the module address via the buon. (Delivery State =1)

6. If necessary, assign a free module address. (Delivery State =1)

7. If a new address has been assigned, the newly assigned address must of course also be entered in

the "Module address" selecon eld, otherwise further programming of the DR5033 is not possible.

8. Enter the CV number to be changed or read in the input eld.

9. Enter the desired value or select the bits to be set.

10. Use the "Read value" or "Write LNCV value" buons to read out the LNCV or write it to the booster.

11. This bar indicates the progress of the read or write process.

Message display of the read/write operaon.

TIMEOUT No module detected (possibly wrong module address entered?!)

OKAY Read/write operaon performed correctly. 4

10 11

DR5033 DIGIBOOST

P 7

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

3.1 LocoNet® Variables (LNCV) Table

LNCV Descripon range Default LNCV Descripon range Default

0Loconet module address 1-9999 112

Waing me aer automac polarity reversal of the track

out before a short circuit is reported to the control unit.

(Seng in 3 millisecond steps.)

32-250 48

1Firmware version (1000 = 1,000)

(Value can only be read) - - 13 Waing me before polarity reversal or short-circuit signal.

(Seng in 3 millisecond steps.) 16-250 32

3Conguraon LNCV siehe unten 92 14 Oponal switching address for polarity reversal of the out-

put 0-2048 0

6Temperature of the H-bridge in degrees °C

(Value can only be read) 0-150 - 15 Polarity reversal ON for feedback A 0-2048 0

7Current load in %

(Value can only be read) 0-100 - 16 Polarity reversal ON for feedback B 0-2048 0

8Turnout address for booster Individual switch-o 0-2048 017 Polarity reversal OFF for feedback D 0-2048 0

Waing me unl restart aer short circuit.

The default value corresponds to approx. one 3/4 second

(750 ms). (Seng is done in three millisecond steps.)

64-30000 244 18 Polarity reversal OFF for feedback E 0-2048 0

Bit Wert Descripon Default Bit Wert Descripon Default

0Not used

0Booster does not send a special LocoNet® message in case of

short-circuit shutdown.

1Not used 16

Booster sends a LocoNet® message in case of a short circuit so

that the central unit can display which booster has been

switched o.

0Track Out acve as soon as an input signal is detected.

0Track Out acve without output polarity reversal (blue LED o)

Track Out acve as soon as the GO/Stop buon of the control

unit is pressed or the connected switching address (LNCV 8) is

switched to green.

32 Track Out acve Output reversed polarity (blue LED on)

0Booster does not send 'GPON/GPOFF' L.NET report on short

circuit. Automac short-circuit repair is enabled. 46

0Automac polarity reversal o

4Booster sends 'GPON/GPOFF' L.NET report to headquarters. The

central determines when the track out is switched on again. 64 Automac polarity reversal on

30Not used 870Not used 0

8Not used 128 Not used

3.2 Descripon Conguraon LNCV

With the LNCV 3 the behaviour (short-circuit behaviour, start behaviour, automac reverse polarity, etc.) of the booster can be adapted.

DR5033 DIGIBOOST

P 8

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

4.0 Connecon examples

The connecon examples shown here represent only a small part of the possibilies for connecng the DR5033 to dierent control panels. Please note that

there are of course further possibilies and special cases which cannot be shown here!

4.1 Important notes on using the DR5033.

• The conguraon is done via LocoNet®.

• The DR5033 can be used with control panels that use an H-bridge to generate track signals.

• The same voltage must be set on the power supply units of the boosters and control panels.

• When using the CDE booster connecon on the DR5033, it must be ensured that the CDE connecon of the central unit meets the specicaons of Fa. Lenz®.

• Operaon of the DR5033 in conjuncon with control panels (e.g. Uhlenbrock®, Piko® Smart ControllerLigth®, etc.) which operate according to the "common

ground principle" is not possible on the same circuit. This can lead to damage to components. Even a busbar separaon on both sides is not sucient! Please

note connecon example 4.9.

• The tracks must always be separated on both sides between the booster and central areas.

• The maximum number of boosters on the Roco® B-Bus® is limited to four.

• The transion voltage between the booster ranges must always be less than 0.8 Volt. This can easily be checked with a mulmeter (seng the measuring

range to AC alternang voltage). Both rail separaons must always be checked. If the value of 0.8 Volt is exceeded, the input voltage of the booster or the

voltage seng of the central unit must be adjusted.

Central Booster

DR50333

The displayed measured value must not

exceed 0.8 Volt!

Always check both track separaons!

DR5033 DIGIBOOST

P 9

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

4.2 Tested central units and connecon types

Central Connecon Possibil-

ies Central

special features

DR5000

B-Bus® No Railcom®, max. 4 boosters possible.

LocoNet® „B“Our recommendaon! Full booster connecon.

Railcom® is generated by the DR5000 and passed on to the booster. The status of

the DR5033, for example, can be queried via LocoNet®. In addion, the booster can

be individually switched o and on again via a magnec arcle address.

Roco®/Fleischmann®

Z 21®

B-Bus® Our recommendaon!

(if the number of 4

Booster is sucient)

No Railcom®, max. 4 boosters possible.

Snier Input Our recommendaon! Railcom® is recognized and passed on by the booster.

LocoNet® Since the Z 21® has no LocoNet® "B" connecon, the DR5033 can only be cong-

ured. Operaon via LocoNet® „B“ on the Z 21 is therefore not possible.

Roco®/Fleischmann®

z21®/z21®Start

B-Bus® Our recommendaon!

(if the number of 4

Booster is sucient)

No Railcom®, max. 4 boosters possible.

Snier Eingang Our recommendaon! Railcom® is recognized and passed on by the booster.

DR5033 DIGIBOOST

P 10

www.digikeijs.com ® R-Bus, B-Bus are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2021-07-06

Central Connecon Possibil-

ies Central

special features

Lenz®

CDE Our recommendaon!

Snier Input

Uhlenbrock®

Intellibox, Intellibox 2,

Intellibox Basis, etc.

LocoNet® „B“Our recommendaon! Full booster connecon.

Railcom® is generated by the central unit and passed on to the booster. The status

of the DR5033, for example, can be queried via LocoNet®. In addion, the booster

can be individually switched o and on again via a magnec arcle address.

Important! As Uhlenbrock® works according to the Common Ground principle, the

track output DR5033 must never be used with the track output of the central unit

on the same circuit. Even a track separaon on both sides is not sucient!

Piko®

Smartcontrol light®

Uhlenbrock® Daisy®

LocoNet® „B“Our recommendaon! Full booster connecon.

Important! AS Piko®/Uhlenbrock® works according to the Common Ground princi-

ple, the track output DR5033 must never be used with the track output of the cen-

tral unit on the same circuit. Even a track separaon on both sides is not sucient!

Please note that it is not possible for us to test all central/booster combinaons available on the market.

Otros manuales para DR5033

Tabla de contenidos

Otros manuales de Extensor de Digikeijs

Digikeijs

Digikeijs DR5033 Manual de usuario

Digikeijs

Digikeijs DR5033 Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario