Digicom VoiceGate ATA Manual de usuario

VoiceGate ATA

User’s Guide

rev. 1.0 10/2007

VoIP Gateway Ethernet

2 VoIP lines

VoIP Gateway Configuration

1.0 Features

Network Protocol

Tone

SIP v1 (RFC2543), v2(RFC3261)

IP/TCP/UDP/RTP/RTCP

IP/ICMP/ARP/RARP/SNTP

TFTP Client/DHCP

Client/ PPPoE Client

Telnet/HTTP Server

DNS Client

NAT/DHCP Server

Ring Tong

Ring Back Tone

Dial Tone

Busy Tone

Programming Tone

Codec

Phone Function

G.711: 64k bit/s (PCM)

G.723.1: 6.3k / 5.3k bit/s

G.726: 16k / 24k / 32k / 40k bit/s (ADPCM)

G.729A: 8k bit/s (CS-ACELP)

G.729B: adds VAD & CNG to G.729

Volume Adjustment

Speed dial key

Phone book

Flash

Voice Quality

IP Assignment

VAD: Voice activity detection

CNG: Comfortable noise generator

LEC: Line echo canceller

Packet Loss Compensation

Adaptive Jitter Buffer

Static IP

DHCP

PPPoE

Call Function

Security

Call Hold

Call Waiting

Call Forward

Caller ID

3-way conference

HTTP 1.1 basic/digest authentication for Web setup

MD5 for SIP authentication (RFC2069/ RFC 2617)

DTMF Function

NAT Traversal

In-Band DTMF

Out-of Band DTMF

SIP Info

STUN

SIP Server

Configuration

Registrar Server, Outbound Proxy

Web Browser , Console/Telnet,IVR/Keypad

Firmware Upgrade

Auto Provisioning

TFTP, Console, HTTP

HTTP, FTP, TFTP

Interface

Modem & Fax modes

1 WAN port interface

1 LAN port interface

2 VOIP port interface (FXS)

G.711 fax/modem pass-through with fax/modem

detection

T.38 support

ARAMETERS THAT YOU NEED TO CONFIGURE THE VOIP GATEWAY

Following table is the parameters that you need to configure the VoIP Gateway.

If you cannot get the Internet/WAN access of your own network and VoIP Configuration of your VoIP Service

Provider, it’s difficult to configure the VoIP Gateway correctly and have it work properly.

Parameters that you need to configure the VoIP Gateway

Internet/WAN Access of your own Network

DHCP Client

PPPoE Client

Static IP

Obtain an IP Address automatically

N/A

Username

N/A

1234

N/A

Password

N/A

1234

N/A

IP Address

N/A

192.168.10.110

Subnet Mask

N/A

255.255.255.0

Gateway

N/A

192.168.10.100

DNS Server IP

N/A

192.168.10.100

VoIP Configuration of Your VoIP Service Provider

Domain Server Address

192.168.10.100

Domain Server Port

5060

Proxy Server Address

192.168.10.100

Proxy Server Port

5060

Outbound Proxy Address

192.168.10.100

Outbound Proxy Port

5060

Note:

* Username / Password which was given by Telecom or by your Internet Service Provider

(ISP).

* IP Address / Subnet Mask / Gateway / DNS Server IP which was given by your network

administrator or by Telecom or by your Internet Service Provider (ISP).

* Domain Server Address and Port / Proxy Server Address and Port / Outbound Proxy

Address and Port / User Name / Register Name / Register Password which was given by

Telecom or by your Internet Service Provider (ISP) or by your VoIP Service Provider.

2. VoIP Gateway Overview

VoIP Gateway has many ports, switches and LEDs. VoIP Gateway may have some or all of the features listed

below

2.1 Ports and Buttons

POWER: Connect the power adapter that came with the VoIP Gateway. Using a power supply with a

different voltage rating will damage this product. Make sure to observe the proper power requirements. The

power requirement is DC12 volts/0.6 A.

POWER Switch: Power on/off the VoIP Gateway.

WAN Port: Connect to Broadband devices, such as a ADSL or Cable modem.

LAN Port: Connect to Ethernet network devices, such as a PC, hub, switch, or router. Depending on the

connection, you may need a cross over cable or a strait through cable.

RESET: The RESET button will set the VoIP Gateway to its factory default setting and reset the VoIP

Gateway. You may need to place the VoIP Gateway into its factory defaults if the configuration is changed,

you loose the ability to enter the VoIP Gateway via the web interface, or following a software upgrade, and

you loose the ability to enter the VoIP Gateway. To reset the VoIP Gateway, simply press the reset button for

more than 10 seconds. The VoIP Gateway will be reset to its factory defaults and after about 30 seconds the

VoIP Gateway will become operational again.

PHONE Jack: Connect a standard telephone handset to the VoIP Gateway phone jack using a telephone

cable.

2.2 LED Description

PWR LED: The LED stays lighted to indicate the system is power on properly.

SIP LED: This LED is lighted when the VoIP Gateway is REGISTERED successfully to the SIP Server.

ETH LED: The LED is lighted when a connection is established to WAN/LAN port and flashes when

WAN/LAN port is sending/receiving data.

3. Installing VoIP Gateway

3.1 Hardware Installation

1. Locate an optimum location for the VoIP Gateway.

2. For connections to all interfaces, refer to figure below.

3. Connect the AC Power Adapter. Depending upon the type of network, you may want to put the power

supply on an uninterruptible supply. Only use the power adapter supplied with the VoIP Gateway. A different

adapter may damage the product.

Now that the hardware installation is complete, proceed to reset Chapters to set up VoIP Gateway.

3.2 Basic VoIP Configuration

3.2.1 Access to the web configuration of VoIP Gateway

Step 1:

1. Launch the Web browser (Internet Explorer, Netscape, etc.).

2. Enter the LAN port default IP address (default gateway) http://10.0.0.2 in the address bar.

3. Entry of the username and password will be prompted. Enter the default login User Name and Password:

The default login User Name of the administrator is admin, and the default login Password is

administrator.

Remember my password checkbox: By default, this box is not checked. Users can check this box so that

Internet Explorer will remember the User name and Password for future logins. It is recommended to leave

this box unchecked for security purposes.

Step 2:

Now you could configure the VoIP Gateway in detail.

3.2.2 VoIP Configuration

Step 1:

Click " Configuration -> VoIP -> SIP Service Provider "

Step 2:

Click On ratio in Active, enter the information of "Domain Server / Proxy Server / OutboundProxy /

Display Name / User Name / Register Name / Register Password " , which was provided by your

VoIP Service Provider and then click "Submit ".

Step 3:

You have to save and reboot the SIP VoIP Gateway to effect those changes.

Tabla de contenidos

Otros manuales de Puerta de Digicom

Digicom

Digicom 3G Industrial Manual de usuario

Digicom

Digicom 8D5824 Manual de usuario

Digicom

Digicom 3G Gateway HSDPA 7.2M Manual de usuario

Digicom

Digicom GSM 2G WLL Manual del propietario

Digicom

Digicom 2G Lift Dialer Manual de usuario

Digicom

Digicom VoiceGATE 8E4137 Manual de usuario

Digicom

Digicom 2G GSM Gateway Fax Manual de usuario

Digicom

Digicom 8D5799 Manual de usuario

Digicom

Digicom Michaelangelo Gateway 8E4088 Manual de usuario

Digicom

Digicom 3G Gateway HSDPA 7.2M Manual de usuario

Digicom

Digicom 3G SOHO 8D5634 Manual de usuario

Digicom

Digicom 3G CORPORATE 8D5633 Manual de usuario

Digicom

Digicom GPRS Card S Manual de usuario

Digicom

Digicom VoiceGATE 8D5499 Manual de usuario

Digicom

Digicom Michelangelo Gateway Manual de usuario

Digicom

Digicom 2G GSM Gateway Lift Manual de usuario

Digicom

Digicom 3G SoHo Manual de usuario

Digicom

Digicom 2G GSM Gateway Voce Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario