Digi-Sense 91428-07 Manual de usuario

Instruction Manual

Single-Input

RTD Thermometer

(Model 91428-07)

68X001350 Rev0 0717 065DGMAN_91428-07

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

TABLE OF CONTENTS

QUICK-START GUIDE............................. 1

1. INTRODUCTION................................ 2

2. SAFETY PRECAUTIONS................... 3

3. SPECIFICATIONS.............................. 4

4. BATTERY INSTALLATION AND

REPLACEMENT................................. 6

5. INSERTING AND REMOVING

OPTIONAL RUBBER ARMOR............ 7

6. ASSEMBLING OPTIONAL HANDS-

FREE ACCESORIES.......................... 8

7. CONNECTING AN RTD PROBE........ 9

8. KEY FUNCTIONS..............................10

9. DISPLAY OVERVIEW .......................11

10. MEASUREMENT MODE ...................12

11. SELECTING TEMPERATURE

SCALE ..............................................13

12. MIN AND MAX FUNCTION................14

13. AUTO OFF FUNCTION.....................14

14. CALIBRATION...................................15

15. CLEAR FIELD CALIBRATION...........16

16. FIELD CALIBRATION UNLOCK........16

17. FIELD CALIBRATION LOCKOUT......17

18. MAINTENANCE.................................18

19. CLEANING........................................18

20. TROUBLESHOOTING.......................19

21. SERVICE...........................................20

22. REPLACEMENT METER &

ACCESSORIES.................................20

23. WARRANTY......................................21

24. PRODUCT RETURN.........................21

25. INNOCAL® CALIBRATION AND

REPAIR SERVICES ..........................22

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

- 1 -

QUICK-

START

GUIDE

To ensure best results please read the

complete manual.

1. Connect probe.

2. Press the on/off key.

Press again to turn on backlight.

3. Select °C or °F display using °C/°F key.

4. Insert probe in sample.

Allow adequate time for reading to

stabilize.

Response time will vary depending on

probe.

5. Take reading.

Press hold key to freeze display.

Press min/max to display minimum or

maximum temperature.

6. Press and hold the on/off key for three

seconds to turn meter off.

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

- 2 -

1. INTRODUCTION

This versatile handheld

instrument provides highly

accurate temperature

measurements and is

designed for easy operation,

which includes the following

features:

xOperator selection of Celsius or

Fahrenheit scale

xResolution of 0.1° (auto ranging)

xFour-digit backlit LCD

xHold feature to retain a reading

temporarily

xField calibration capability

xLow-battery warning

xAuto power off with Enable/Disable

function

xMin and Max readings display

x3-pin circular connector input

xOperates with a wide selection of

probes

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

- 3 -

2. SAFETY PRECAUTIONS

Voltages present at the RTD may also be

present at the battery terminals. Always

disconnect the RTD when changing

batteries.

This instrument is designed to accept low

level signals supplied by standard 100 Ω

RTDs. Under no circumstances should the

input voltage exceed the specified 10V rms.

1. Do not use or store this instrument in

microwave ovens or any abnormally

hot or cold areas.

2. Weak batteries should not be left in the

instrument. Dead batteries can leak and

cause damage to unit.

WWARNING

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

- 4 -

3. SPECIFICATIONS

Platinum RTD Probes

100 ohm platinum: alpha = 0.003850

–200 to 850°C (–392 to 1562°F)

Out-of-range display: “Ur”, “Or”, “OPEN”

Range

Accuracy

–200.0 to –100.0°C

(–392 to –148°F)

±2.0°C

(±4.0°F)

–99.9 to 199.9°C

(–148 to 392°F)

±0.2°C

(±0.4°F)

200.0 to 850.0°C

(392 to 1562°F)

±2.0°C

(±4.0°F)

Resolution

0.1° (–200.0 to 850.0°C);

0.1° (

–392.0 to 999.9°F);

1° (1000 to 1562°F)

Display

4-digit LCD (¼ x ½" digits);

1/3x

1 ½" backlit viewing

area

Display update

rate

0.5 sec per updat

Input

One probe with 3 pin circular

connector (Switchcraft TA3F)

Input protection

10V rms

Battery

Three AA, 1.5V alkaline

Battery life

700 hours continuous

Auto

shutoff

17 minutes after last

keypress

Stated

accuracy

18 to 28°C

(64 to 82°F)

Useful

range

0 to 40°C

(32 to 104°F)

Storage

–40 to 65°C

(–40 to 149°F)

Humidity

10% to 90% RH

(noncondensing)

Dimensions

Without armor

With armor

(L x W x H )

175 mm x 97 mm x 42 mm

180 mm x 102 mm x 52 mm

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

- 5 -

Weight

Without armor

With armor

267 g

362 g

Ingress protection

(

with probe

attached)

Meets IEC-529 IP54 for

dust

and water-resistant

enclosures

compliance

EN61326-1/A1:

1998 (EU EMC Directive)

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

- 6 -

4. BATTERY INSTALLATION AND

REPLACEMENT

Voltages present at the RTD may also be

present at the battery terminals. Always

disconnect the RTD when changing

batteries.

Weak batteries should not be left in the

instrument. Dead batteries can leak and

cause damage to unit.

The typical battery life is about 700 hours.

Selected settings are stored in memory and

will remain in memory even after power is

turned off, or while batteries are being

replaced.

1. Before

changing

batter

, tur

instrume

nt off

and

disconnect probe

Loosen

screw

and

lift batter

cover

off

the

back

of case.

Remove

the t

hree

AA batteries.

4. Insert three

new

batteri

observing

pol

arit

5. Install

cover

and

tig

ten

screw

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

- 7 -

5. INSERTING AND REMOVING

OPTIONAL RUBBER ARMOR

Figure 1: Removing Optional Rubber Armor

1. To insert thermometer into the optional

rubber armor, slide in from the top of

meter before pushing the bottom edges

of meter down to set it into position. Lift

up the stand at the back of meter for

bench top applications if necessary.

2. To remove thermometer from armor,

push out from the bottom edges of meter

until it is completely out of boot.

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

- 8 -

6. ASSEMBLING OPTIONAL

HANDS-FREE

ACCESORIES

You can use the optional magnets and

strap in the Hands-Free Kit accessories for

hands-free operations.

Figure 2: Hands-Free Kit

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

Tabla de contenidos

Otros manuales de Termómetro de Digi-Sense

Digi-Sense

Digi-Sense 93210-50 Manual de usuario

Digi-Sense

Digi-Sense Traceable 90205-10 Manual de usuario

Digi-Sense

Digi-Sense 91428-03 Manual de usuario

Digi-Sense

Digi-Sense 20250-91 Manual de usuario

Digi-Sense

Digi-Sense 20250-04 Manual de usuario

Digi-Sense

Digi-Sense 20250-01 Manual de usuario

Digi-Sense

Digi-Sense 20250-92 Manual de usuario

Digi-Sense

Digi-Sense 20250-33 Manual de usuario

Digi-Sense

Digi-Sense 20250-02 Manual de usuario

Digi-Sense

Digi-Sense Type K Manual de usuario

Digi-Sense

Digi-Sense 93410-00 Manual de usuario

Digi-Sense

Digi-Sense 20250-07 Manual de usuario

Digi-Sense

Digi-Sense Dual J-T-EK 60010-40 Manual de usuario

Digi-Sense

Digi-Sense J Manual de usuario

Digi-Sense

Digi-Sense ThermoLogR 93410-50 Manual de usuario

Digi-Sense

Digi-Sense 20250-20 Manual de usuario

Digi-Sense

Digi-Sense 20250-34 Manual de usuario

Digi-Sense

Digi-Sense 20250-09 Manual de usuario

Digi-Sense

Digi-Sense 20250-05 Manual de usuario

Digi-Sense

Digi-Sense 20250-91 Manual de usuario

Digi-Sense

Digi-Sense 20250-18 Manual de usuario

Digi-Sense

Digi-Sense 20250-32 Manual de usuario

Digi-Sense

Digi-Sense 92000-01 Manual de usuario

Digi-Sense

Digi-Sense 69202-30 Manual de usuario

Manuales populares de Termómetro de otras marcas

Delton

Delton 981A Manual de usuario

Baker

Baker MM2P Manual de usuario

Tarmo

Tarmo 320281 Manual de usuario

Citizen

Citizen CTD 504 Manual de usuario

TFA

TFA 14.1500 Manual de usuario

Vive

Vive DMD1010 Manual de usuario

Gotemp

Gotemp THB4002 Manual de usuario

GREISINGER

GREISINGER G 1202 Manual de usuario

Amprobe

Amprobe TMD-53W Manual de usuario

Trotec

Trotec BP10 Manual de usuario

Radiance instruments

Radiance instruments RT616 Series Manual de usuario

Eurolec

Eurolec IR151 Manual de usuario

Scaneo

Scaneo TS42B Manual de usuario

Sper scientific

Sper scientific 800043 Manual de usuario

Microlife

Microlife NC 200 Manual de instrucciones

Motorola

Motorola MBP69SN Guía de configuración

The MeatStick

The MeatStick The MeatStick Manual de usuario

Hama

Hama TH35-A Manual de usuario