Di-soric ID-08 Manual de usuario

ID-08 / ID-09 Handheld Reader

User’s Manual

ID-08 / ID-09 User´s Manual

ii ID-08 / ID-09 High Performance Imager – User´s Manual

ISO 9001 Certified

Issued by TüV USA

of allowing customers to operate and/or service di-soric manufactured equipment and is not to be

released, reproduced, or used for any other purpose without written permission of di-soric.

Throughout this manual, trademarked names might be used. Rather than place a trademark (™) symbol

at every occurrence of a trademarked name, we state herein that we are using the names only in an editorial

fashion, and to the benefit of the trademark owner, with no intention of infringement.

Disclaimer

The information and specifications described in this manual are subject to change without notice.

Latest Manual Version

For the latest version of this manual, see the Download Center on our web site at:

www.di-soric.com.

Technical Support

For technical support, e-mail: [email protected].

Warranty and Terms of Sale

For Standard Warranty information contact:

di-soric GmbH & Co. KG

Steinbeisstraße 6

DE-73660 Urbach

Fon: +49 (0) 71 81 / 98 79 - 0

Fax: +49 (0) 71 81 / 98 79 - 179

[email protected]

www.di-soric.com

ID-08 / ID-09 High Performance Imager – User´s Manual

Introduction

Table of Contents

Chapter 1 Quick Start

Check Required Hardware ......................................................................1-2

USB Interface ..........................................................................................1-3

RS-232 Interface......................................................................................1-4

Install ID-Software ...................................................................................1-5

Select Model............................................................................................1-6

Select Interface and Connect to Reader..................................................1-7

Configure the Reader ..............................................................................1-9

Save Changes in ID-Software ...............................................................1-10

Chapter 2 Using ID-Software

EZ Mode..................................................................................................2-2

Application Mode.....................................................................................2-3

Tree Controls...........................................................................................2-4

Menu Toolbar...........................................................................................2-5

Send/Receive ....................................................................................... 2-15

Chapter 3 Basic Operations

Practice Targeting....................................................................................3-2

Motion Detect Mode.................................................................................3-3

Dual Optics..............................................................................................3-4

Operational Feedback .............................................................................3-6

Chapter 4 Communications

Communications by ID-Software.............................................................4-2

Communications Overview......................................................................4-3

USB Interface ..........................................................................................4-4

RS-232 Interface......................................................................................4-5

Preamble .................................................................................................4-7

Postamble................................................................................................4-8

Preamble and Postamble by ID-Software................................................4-9

Keyboard Mapping.................................................................................4-10

Communications Mode..........................................................................4-11

USB Keyboard Rate ..............................................................................4-13

RS-232...................................................................................................4-14

Text Command Timeout........................................................................4-15

Chapter 5 Read Cycle

Read Cycle by ID-Software .....................................................................5-2

External Trigger.......................................................................................5-3

Default Continuous Event........................................................................5-4

Maximum Decodes per Read..................................................................5-5

Read Cycle Timeout................................................................................5-6

Ignore Duplicate Symbol Timeout............................................................5-7

Targeting Zone Tolerance .......................................................................5-8

Morphological Preprocessing ..................................................................5-9

Camera Settings....................................................................................5-10

iv ID-08 / ID-09 High Performance Imager – User´s Manual

Table of Contents

Chapter 6 Symbologies

Symbologies by ID-Software...................................................................6-2

Data Matrix..............................................................................................6-3

QR Code..................................................................................................6-4

Aztec........................................................................................................6-5

Code 39...................................................................................................6-6

Code 128.................................................................................................6-7

BC412......................................................................................................6-8

Code 93...................................................................................................6-9

Codabar.................................................................................................6-10

Interleaved 2 of 5...................................................................................6-11

UPC.......................................................................................................6-12

Postal.....................................................................................................6-13

Pharmacode..........................................................................................6-14

GS1 DataBar.........................................................................................6-16

PDF417 .................................................................................................6-17

MicroPDF417.........................................................................................6-18

Composite .............................................................................................6-19

Symbology Identifier..............................................................................6-20

Chapter 7 I/O Parameters

I/O Parameters by ID-Software ...............................................................7-2

No Read Notification................................................................................7-3

Targeting .................................................................................................7-4

Beeper.....................................................................................................7-5

Vibrate.....................................................................................................7-6

Button Stay-Down Time...........................................................................7-7

Motion Detect Event................................................................................7-8

Image Quality ..........................................................................................7-9

Chapter 8 Advanced Operations

Continuous Read.....................................................................................8-2

Mirroring ..................................................................................................8-3

Motion Detection......................................................................................8-4

Window of Interest...................................................................................8-5

Chapter 9 Terminal

Terminal View..........................................................................................9-2

Find..........................................................................................................9-3

Send........................................................................................................9-4

Macros.....................................................................................................9-5

Terminal Right-Click Menu......................................................................9-6

Terminal Dropdown Menu.......................................................................9-7

Chapter 10 Utilities

Device Control.......................................................................................10-2

Differences from Default........................................................................10-3

Firmware................................................................................................10-4

Advanced...............................................................................................10-6

ID-08 / ID-09 High Performance Imager – User´s Manual

Introduction

Appendices

Appendix A General Specifications ........................................................ A-2

Appendix B Electrical Specifications....................................................... A-5

Appendix C Configuration Symbols........................................................ A-6

Appendix D Serial Commands.............................................................. A-17

Appendix E Communications Protocol ................................................. A-48

Appendix F ASCII Table....................................................................... A-49

Appendix G Maintenance ..................................................................... A-50

Appendix H Glossary of Terms............................................................. A-51

vi ID-08 / ID-09 High Performance Imager – User´s Manual

About the ID-08 and ID-09 Handheld Readers

The ID-08 is a general-purpose 2D reader. Its many features include dual field optics for

both high density and wide angle performance, a ruggedized design, IP54 sealing against

dust and water, and compact size.

The ID-09 is a special-purpose 2D reader for decoding direct part marks (DPM).

di-soric’s X-

Mode decode algorithms make the ID-09 an ideal solution for reading difficult

marks on many

surfaces, including PCBs, electrical components, castings, and sheet metal.

Its tough design

makes it a good choice for manufacturing and light industrial applications.

Both readers can be configured and tested easily using the intuitive tree controls and user

interface of di-soric’s ID-Software.

Note: The ID-08 and ID-09 have unique algorithm licenses, and the ID-08 cannot be field-

upgraded to an ID-09.

About This Manual

This manual provides complete information on setting up, installing, and configuring the

ID-08 and ID-09. The chapters are presented in the order in which the reader would be

assembled, configured, and optimized.

Highlighting

Cross-references and web addresses are highlighted in blue bold.

References to ID-Software, its toolbar headings, and menu headings are highlighted in Bold Ini-

tial Caps.

ID-08 / ID-09 High Performance Imager – User´s Manual

Introduction

Statement of Agency Compliance

The ID-08 and ID-09 have been tested for compliance with FCC regulations and were

found to be compliant with all applicable FCC Rules and Regulations.

IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, this

device must not be co-located or operate in conjunction with any other antenna or transmitter.

CAUTION: Changes or modifications not expressly approved by the party rID-Softwareon-

sible for compliance could void the user’s authority to operate the equipment.

The ID-08 and ID-09 have been tested for compliance to CE (Conformité Européenne)

standards and guidelines and were found to conform to applicable CE standards, specifically

the EMC requirements EN 55024, ESD EN 61000-4-2, Radiated RF Immunity EN 61000-4-3,

ENV 50204, EFT EN 61000-4-4, Conducted RF Immunity EN 61000-4-6, EN 55022, Class

B Radiated Emissions, and Class B Conducted Emissions.

viii ID-08 / ID-09 High Performance Imager – User´s Manual

Statement of RoHS Compliance

All compliant readers were converted prior to March 1, 2007. All standard accessories in

the di-soric Product Pricing Catalog are RoHS-Compliant except 20-500013-01 and 98-

000039-02. These products meet all the requirements of “Directive 2002/95/EC” European

Parliament and the Council of the European Union for RoHS compliance. In accordance

with the latest requirements, our RoHS-Compliant products and packaging do not contain

intentionally added Deca-BDE, Perfluorooctanes (PFOS), or Perfluorooctanic Acid

(PFOA) compounds above the maximum trace levels. To view the document stating these

requirements, please visit:

http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=CELEX:32002L0095:EN:HTML

and

http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=OJ:L:2006:372:0032:0034:EN:PDF

Please contact your sales manager for a complete list of di-soric’s RoHS-Compliant products.

This declaration is based upon information obtained from sources which di-soric believes to be reliable, and from

random sample testing; however, the information is provided without any representation of warranty, expressed

or implied, regarding accuracy or correctness. di-soric does not specifically run any analysis on our raw materials

or end product to measure for these substances.

The information provided in this certification notice is correct to the best of di-soric’s knowledge at the date of

publication. This notice is not to be considered a warranty or quality specification. Users are rID-Softwareonsible

for determining the applicability of any RoHS legislation or regulations based on their individual use of the prod-

uct.

Regarding “RoHS Directive 2011_65_EU” di-soric produces Monitoring and Control Instruments as well as Indus-

trial Monitoring and Control Instruments as defined within the directive. di-soric has developed and is implement-

ing a RoHS2 compliance plan with the intention of bringing all active products listed in our current marketing

literature within full compliance as per the directive deadlines.

Key milestones for the transition plan are as follows:

• Complete internal product audit and supplier transition by July 2013.

• Initial “Monitoring and Control Instruments” RoHS2-compliant products available by July 2014.

• Initial “Industrial Monitoring and Control Instruments” RoHS2-compliant products available by July 2015.

• All new products introduced in 2014 are expected to be WEEE and RoHS2 compliant.

di-soric will mark the products with the ‘CE’ marking that complies with the RoHS2 process to acquire ‘CE’ certification

per the example given: Example 1 >> Machinery directive + EMC directive + RoHS2 = Declaration of Conformity.

ID-08 / ID-09 High Performance Imager – User´s Manual 1-1

1 Quick Start

Contents

This section is designed to get your ID-08 or ID-09 Handheld Reader up and running

quickly using di-soric’s ID-Software so you can get a sense of its capabilities and test sam-

ple symbols. Detailed setup information for configuring the reader for your specific appli-

cation can be obtained in the subsequent sections.

Your interface type will determine how data is received by the host. When sending data by

USB, you must open a text editor in your host computer. When sending data by RS-232, you

must use a terminal program such as ID-Software Terminal view.

Check Required Hardware...........................................................................................................1-2

USB Interface...............................................................................................................................1-3

RS-232 Interface ..........................................................................................................................1-4

Install ID-Software........................................................................................................................1-5

Select Model.................................................................................................................................1-6

Select Interface and Connect to Reader ......................................................................................1-7

Configure the Reader...................................................................................................................1-9

Save Changes in ID-Software....................................................................................................1-10

1-2 ID-08 / ID-09 High Performance Imager – User´s Manual

Check Required Hardware

The ID-08 / ID-09 is shipped with one of the following cables:

USB Hardware

• ID-08 / ID-09 Handheld Reader

• USB Cable

RS-232 Hardware

• ID-08 / ID-09 Handheld Reader

• RS-232 Cable

• RS-232 Power Supply

Changing Cable and Communications Interface

The reader can be converted from USB to RS-232 or from RS-232 to USB by changing

the cable and scanning the appropriate communications programming symbol below. To

detach the USB or RS-232 cable from the reader, press a paper clip into the hole on the

side of the handle and gently pull the cable out of the connector.

6’ USB Straight Cable 8’ RS-232 Coiled Cable

USB Interface RS-232 Interface Save

Settings

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lector de código de barras de Di-soric

Di-soric

Di-soric ID-200 Manual de usuario

Di-soric

Di-soric ID-100 Manual de usuario

Di-soric

Di-soric ID-110 Manual de usuario

Di-soric

Di-soric ID-09 Manual de usuario

Di-soric

Di-soric ID-100 Manual de usuario

Di-soric

Di-soric ID-200 Manual de usuario

Di-soric

Di-soric ID-10 Manual de usuario

Di-soric

Di-soric ID-80 Manual de usuario

Di-soric

Di-soric ID-80 Manual de usuario

Di-soric

Di-soric ID-110 Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario