DFI KT600-AL Manual de usuario

KT600-AL

Rev.A+

System Board

User’s Manual

78700345

This publication contains information that is protected by copy-

right. No part of it may be reproduced in any form or by any

means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with re-

spect to the contents or use of this manual and specifically dis-

claims any express or implied warranties of merchantability or

fitness for any particular purpose. The user will assume the entire

risk of the use or the results of the use of this document. Further,

the manufacturer reserves the right to revise this publication and

make changes to its contents at any time, without obligation to

notify any person or entity of such revisions or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM, Windows®95, Windows®98,

Windows®98 SE, Windows®ME, Windows®200 and Windows®

XP are registered trademarks of Microsoft Corporation. AMD,

AthlonTM XP, AthlonTM and DuronTM are registered trademarks of

Advanced Micro Devices, Inc.VIA is a registered trademark of VIA

Technologies, Inc. Award is a registered trademark of Award Soft-

ware, Inc. Other trademarks and registered trademarks of prod-

ucts appearing in this manual are the properties of their respec-

tive holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servic-

ing, cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

by the manufacturer.

• Dispose of used batteries according to the battery manufac-

turer’s

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses and can ra-

diate radio frequency energy and, if not installed and used in ac-

cordance with the instruction manual, may cause harmful interfer-

ence to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the re-

ceiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's author-

ity to operate the equipment.

2. Shielded interface cables must be used in order to comply

with the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.

The autorun screen (Mainboard Utility CD) will appear. Click the

“TOOLS” icon then click “Manual” on the main menu.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications.................................................................................

1.2 Package Checklist...........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ..............................................................................................

2.2 System Memory..............................................................................................................

2.3 CPU................................................................................................................................................

2.4 Jumper Settings.................................................................................................................

2.5 Rear I/O Panel..................................................................................................................

2.6 I/O Connectors...............................................................................................................

Chapter 3 - BIOS Setup

3.1 Award BIOS Setup Utility....................................................................................

3.2 VIA RAID BIOS................................................................................................................

3.3 Updating the BIOS.......................................................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface....................................................................

4.2 Drivers and Utilities Installation Notes................................................

4.3 3D Audio Configuration.........................................................................................

4.4 Installation Notes...........................................................................................................

102

104

Introduction

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function......................................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................................

B.2 Error Messages..............................................................................................................

Appendix C -Troubleshooting

C.1 Troubleshooting Checklist....................................................................................

109

105

111

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• VIA®chipset

- North bridge:VIA®KT600

- South bridge:VIA®VT8237

Processor

The system board is equipped with Socket-A for 462-pin PGA

processor. It is also equipped with a switching voltage regulator

that automatically detects 1.100V to 1.850V.

• AMD AthlonTM XP 266/333/400MHz FSB

• AMD AthlonTM 200/266MHz FSB

• AMD DuronTM 200/266MHz FSB

Important:

To ensure proper boot up and operation of your system, you

must power-off the system then turn off the power supply’s

switch or unplug the AC power cord prior to replacing the CPU.

System Memory

• Three 184-pin DDR SDRAM DIMM sockets

• Supports up to 3GB memory (unbuffered DIMM)

• Supports PC1600 (DDR200), PC2100 (DDR266), PC2700

(DDR333) and PC3200 (DDR400) DDR SDRAM DIMM, 2.5V

type

Chapter1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

Expansion Slots

• 1 AGP slot

• 5 PCI slots

AGP (Accelerated Graphics Port)

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The univer-

sal AGP slot supports AGP 8x with up to 2.13GB/sec. bandwidth

and AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics

applications. AGP in this system board will deliver faster and bet-

ter graphics to your PC.

Onboard LAN Features

• VIA 6103 LAN Phy

• Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compatible

PHY

• 32-bit PCI master interface

• Integrated power management functions

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

Onboard Audio Features

• AC’97 2.2 S/PDIF extension compliant codec

• Supports Microsoft®DirectSound / DirectSound 3D

• AC’97 supported with full duplex, independent sample rate

converter for audio recording and playback

• S/PDIF-in/out compressed digital output

• 6-channel audio output

Introduction

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital

audio signals to a device without having to be converted first to

an analog format. This prevents the quality of the audio signal

from degrading whenever it is converted to analog. S/PDIF is usu-

ally found on digital audio equipment such as a DAT machine or

audio processing device. The S/PDIF connector on the system

board sends surround sound and 3D audio signal outputs to am-

plifiers and speakers and to digital recording devices like CD re-

corders.

6-channel Audio

The 6-channel audio output function is supported by using the

surround connector, the audio jacks at the rear panel and

configuring the audio driver and utility. Please refer to chapters 2

and 4.

SATA IDE Interface with RAID

• Supports two SATA (Serial ATA) interfaces which are compli-

ant with SATA 1.0 specification (1.5Gbps interface)

• Supports RAID 0, RAID 1 and JBOD

Serial ATA (SATA) is a storage interface that is compliant with

SATA 1.0 specification. With speed of up to 1.5Gbps, it improves

hard drive performance even in data intensive environments such

as audio/video, consumer electronics and entry-level servers.

Introduction

PCI Bus Master IDE Controller

• Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

• UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

USB Ports

The system board supports USB 2.0 and USB 1.1. USB 1.1 sup-

ports 12Mb/second bandwidth while USB 2.0 supports 480Mb/

second bandwidth providing a marked improvement in device

transfer speeds between your computer and a wide range of si-

multaneously accessible external Plug and Play peripherals.

BIOS

• Award BIOS, Windows®95/98/2000/ME/XP Plug and Play

compatible

• Supports SCSI sequential boot-up

• Flash EPROM for easy BIOS upgrades

• Supports DMI 2.0 function

• 2Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS.The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in

the DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on

using the DMI utility.

Tabla de contenidos

Otros manuales de Placa madre de DFI

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario