DFI WB72-SC Manual de usuario

WB72-SCWB72-SC

WB72-SC

Rev. A+Rev. A+

Rev. A+

System BoardSystem Board

System Board

User’s ManualUser’s Manual

User’s Manual

51300131

CopyrightCopyright

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

TrademarksTrademarks

Trademarks

Windows®98, Windows®98 SE, Windows®ME, Windows®2000

and Windows NT®4.0 are registered trademarks of Microsoft

Corporation. Intel®and Pentium®4 are registered trademarks of

Intel Corporation. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

CautionCaution

Caution

To avoid damage to the system:

• Use the correct AC input voltage range..

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class BFCC and DOC Statement on Class B

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Introduction

TableofContents

Chapter 1 - Introduction

1.1Features and Specifications..................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ..........................................................................................

2.2 System Memory...........................................................................................................

2.3 Jumper Settings for Clearing CMOS Data........................................

2.4 Jumper Settings for Wake-On-Keyboard/Mouse..................................

2.5 Jumper Settings for Wake-On-USB Keyboard................................

2.6 Jumper Settings for USB 4................................................................................

2.7 Ports and Connectors...........................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1.2 Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 CPU Frequency Control..................................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.12 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• Intel®845 chipset

- Intel®82845 Memory Controller Hub (MCH)

- Intel®82801BA I/O Controller Hub (ICH2)

Processor

The system board is equipped with Socket 423 for installing a

Pentium®4 processor.

• Intel®Pentium®4 processor

• 400MHz system data bus

System Memory

• Three 168-pin PC SDRAM DIMM sockets

• Supports 3GB system memory

- Uses 64Mbit, 128Mbit, up to 1.5GB using 256Mbit or up to

3GB using 512Mbit technology, PC-100/PC-133 PC SDRAM

DIMM

• Supports ECC function

Chapter1-Introduction

DIMMs

2MBx64/x72

4MBx64/x72

8MBx64/x72

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64/x72

32MBx64/x72

64MBx64/x72

Memory Size

128MB

256MB

512MB

Introduction

Expansion Slots

The system board is equipped with 1 AGP slot, 4

dedicated PCI slots and 1 shared PCI/CNR slot.

The AGP slot only supports 1.5V AGP 4x (1066MB/sec.

bandwidth) add-in cards. AGP is an interface designed

to support high performance 3D graphics cards for 3D

graphics applications. It handles large amounts of

graphics data with the following features:

• Pipelined memory read and write operations that hide

memory access latency.

• Demultiplexing of address and data on the bus for

nearly 100 percent efficiency.

CNR (Communication and Networking Riser) is an

interface that supports multi-channel audio, V.90

analog modem, phone-line based networking or 10/100

Ethernet based networking riser board.

Onboard Audio Features

• 18-bit stereo full-duplex codec with independent

variable sampling rate

• High quality differential CD input

• True stereo line level outputs

Compatibility

• Microsoft PC ’98 compliant

• PCI 2.2, CNR 1.0 “A” type and AC ’97 compliant

• Intel AGP version 2.0

ATX Double Deck Ports (PC 99 color-coded connectors)

• Two USB ports

• Two NS16C550A-compatible DB-9 serial ports

• One SPP/ECP/EPP DB-25 parallel port

• One mini-DIN-6 PS/2 mouse port

• One mini-DIN-6 PS/2 keyboard port

• One game/MIDI port

• Three audio jacks: line-out, line-in and mic-in

Introduction

Connectors

• One connector for 2 additional external USB ports

• One connector for IrDA interface

• Two IDE connectors

• One floppy drive interface supports up to two

2.88MB floppy drives

• Three ATX power supply connectors

• One Wake-On-LAN connector

• One Wake-On-Ring connector

• CPU, system and second fan connectors

• Two internal audio connectors (CD-in and TAD)

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE

devices

• Supports ATA/33, ATA/66 and ATA/100 hard drives

• PIO Mode 4 Enhanced IDE (data transfer rate up to

14MB/sec.)

• Bus mastering reduces CPU utilization during disk

transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector

for wireless connectivity between your computer and

peripheral devices. It supports peripheral devices that

meet the IrDA or ASKIR standard.

USB Ports

The system board supports 4 USB ports. Two onboard

USB ports are located at the ATX double deck ports of

the board. The J16 connector on the system board

allows you to connect the optional 3rd and 4th USB

ports.

Introduction

BIOS

• Award BIOS, Windows®98/2000/ME/XP Plug and Play

compatible

• Flash EPROM for easy BIOS upgrades

• Supports DMI 2.0 function

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the

BIOS. The DMI utility in the BIOS automatically records

various information about your system configuration

and stores these information in the DMI pool, which is

a part of the system board's Plug and Play BIOS. DMI,

along with the appropriately networked software, is

designed to make inventory, maintenance and

troubleshooting of computer systems easier. Refer to

chapter 4 for instructions on using the DMI utility.

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the

following “system health” conditions.

• Monitors CPU/system temperature and overheat

alarm

• Monitors 5VSB/VBAT/3.3V/5V/±12V/CPU voltages

and failure alarm

• Monitors the fan speed of the CPU fan, system fan

and second fan; and failure alarm

• Automatic system fan and second fan on/off control

• Read back capability that displays temperature,

voltage and fan speed

Introduction

1.1.3 Intelligence

Automatic System/Second Fan Off

The system and second fans will automatically turn off

once the system enters the Suspend mode.

Dual Function Power Button

Depending on the setting in the “Soft-Off By PWR-

BTTN” field of the Power Management Setup, this switch

will allow the system to enter the Soft-Off or Suspend

mode.

Wake-On-Ring

This feature allows the system that is in the Suspend

mode or Soft Power Off mode to wake-up/power-on to

respond to calls coming through an internal or external

modem. Refer to “Wake-On-Ring Connector” in chapter

2 and “Resume On Ring” in the Power Management

Setup section in chapter 3 for more information.

Important:

If you are using a modem add-in card, the 5VSB

power source of your power supply must support

≥720mA.

Wake-On-LAN

The Wake-On-LAN function allows the network to

remotely wake up a Soft Power Down (Soft-Off) PC.

Your LAN card must support the remote wakeup

function. Refer to “Wake-On-LAN Connector” in chapter

2 and “Resume On LAN” in the Power Management

Setup section in chapter 3 for more information.

Important:

The 5VSB power source of your power supply

must support ≥720mA.

Introduction

Wake-On-Keyboard/Wake-On-Mouse

This function allows you to use the keyboard or PS/2

mouse to power-on the system. Refer to “Jumper

Settings for Wake-On-Keyboard/Wake-On-Mouse” in

chapter 2 and “Keyboard/Mouse Power On” in the

Integrated Peripherals section in chapter 3 for more

information.

Important:

• The power button will not function once a

keyboard password has been set in the “KB

Power On Password” field of the Integrated

Peripherals submenu. You must type the

correct password to power-on the system. If

you forgot the password, power-off the system

and remove the battery. Wait for a few seconds

and install it back before powering-on the

system.

• The 5VSB power source of your power supply

must support ≥720mA.

Wake-On-USB Keyboard

The Wake-On-USB Keyboard function allows you to use

a USB keyboard to wake up a system that is in the S3

(STR - Suspend To RAM) state. Refer to “Jumper Settings

for Wake-On-USB Keyboard” in chapter 2 and “USB KB

Wake-Up From S3” in the Power Management Setup

section in chapter 3 for more information.

Important:

• If you are using the Wake-On-USB Keyboard

function for 2 USB ports, the 5VSB power

source of your power supply must support

≥1.5A.

• If you are using the Wake-On-USB Keyboard

function for 4 USB ports, the 5VSB power

source of your power supply must support

≥2A.

Otros manuales para WB72-SC

Tabla de contenidos

Otros manuales de Placa madre de DFI

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario