DFI AD73 Pro Manual de usuario

AD73 Pro/B

Rev. B1

System Board

Users Manual

935-AD73P2-100

70800308

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft® MS-DOS®, WindowsTM, Windows® 95, Windows® 98,

Windows® 98 SE, Windows® ME, Windows® 000, Windows NT®

4.0 and Windows® XP are registered trademarks of Microsoft

Corporation. AMD, AthlonTM and DuronTM are registered trademarks

of Advanced Micro Devices, Inc. VIA is a registered trademark of

VIA Technologies, Inc. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

 Use the correct AC input voltage range.

To reduce the risk of electric shock:

 Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

 Danger of explosion if battery incorrectly replaced.

 Replace only with the same or equivalent type recommend by

the manufacturer.

 Dispose of used batteries according to the battery

manufacturers instructions.

Joystick or MIDI port:

 Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This users manual contains detailed information about the system

board. If, in some cases, some information doesnt match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the users manual, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click Users

Manual.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1. Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

.1 System Board Layout .............................................................................................

. System Memory.............................................................................................................

.3 Jumper Settings for Clearing CMOS Data..........................................

.4 Jumper Settings for the Onboard Audio Codec .........................

.5 Jumper Settings for Selecting the CPUs Front Side

Bus..............................................................................................................................................

.6 Jumper Settings for Selecting the USB Power...................................

.7 Jumper Settings for Selecting the PS/ Power..................................

.8 Ports and Connectors............................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1. Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 Frequency/Voltage Control............................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.1 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

3. Updating the BIOS.....................................................................................................

Introduction

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4. Drivers, Utilities and Software Application............................................

4.3 Installation Notes...........................................................................................................

Appendi A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function........................................................

Appendi B - System Error Messages

B.1 POST Beep.......................................................................................................................

B. Error Messages..............................................................................................................

Appendi C - Troubleshooting

C.1 Troubleshooting Checklist....................................................................................

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

 VIA® KT- 66A and VT8 35

Processor

The system board is equipped with Socket-A for PGA processor. It

is also equipped with a switching voltage regulator that automatically

detects 1.100V to 1.850V.

 AMD AthlonTM XP 66MHz FSB

 AMD AthlonTM 00/ 66MHz FSB

 AMD DuronTM 00MHz FSB

Important:

To ensure proper boot up and operation of your system, you

must power-off the system then turn off the power supplys

switch or unplug the AC power cord prior to replacing the CPU.

System Memory

 Supports up to 3GB memory

 Uses .5V PC1600 (DDR 00) / PC 100 (DDR 66) DDR

SDRAM DIMM

 Three 184-pin DDR SDRAM DIMM sockets

 L cache memory

- DuronTM processor: built-in 64KB Level pipelined burst

cache

- AthlonTM XP / AthlonTM processor: built-in 56KB Level

pipelined burst cache

Chapter 1 - Introduction

Introduction

xpansion Slots

The system board is equipped with 1 universal AGP slot and 5 PCI

slots.

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The universal

AGP slot supports AGP x with up to 533MB/sec. bandwidth and

AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics

applications. AGP in this system board will deliver faster and better

graphics to your PC.

Onboard Audio Features

 Supports Microsoft® DirectSound/DirectSound 3D

 AC97 supported with full duplex, independent sample rate con-

verter for audio recording and playback

Rear Panel I/O Ports (PC 99 color-coded connectors)

 Two USB ports

 Two NS16C550A-compatible DB-9 serial ports

 One SPP/ECP/EPP DB- 5 parallel port

 One mini-DIN-6 PS/ mouse port

 One mini-DIN-6 PS/ keyboard port

 One game/MIDI port

 Three audio jacks: line-out, line-in and mic-in

I/O Connectors

 Two connectors for 4 additional external USB ports

 One connector for IR and CIR interface

 Two IDE connectors

 One floppy drive interface supports up to two .88MB floppy

drives

 One ATX power supply connector

 One Wake-On-LAN connector

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

 One Wake-On-Ring connector

 CPU, chassis and second chassis fan connectors

 One internal audio (CD-in) connector

 One connector for external line-out and mic-in jacks

PCI Bus Master ID Controller

 Two PCI IDE interfaces support up to four IDE devices

 Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

 UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-1 0 and ZIP

IrDA Interface

The system board is equipped with IR and CIR connectors for wire-

less connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the IrDA and ASKIR standard.

USB Ports

The system board supports 6 USB (USB .0/1.1 compliant) ports.

Two onboard USB ports are located at the ATX double deck ports

of the board. The J 7 and J 8 connectors on the system board

allows you to connect 4 more optional USB ports. These optional

USB ports, which are mounted on a card-edge bracket, will be pro-

vided as an option. USB allows data exchange between your com-

puter and a wide range of simultaneously accessible external Plug

and Play peripherals.

BIOS

 Award BIOS, Windows® 95/98/ 000/ME/XP Plug and Play

compatible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades

 Supports DMI .0 function

 Mbit flash memory

 Vcore and CPU external bus clock selectable in the BIOS

Introduction

Desktop Management Interface (DMI)

The system board comes with a DMI .0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following system

health conditions.

 Monitors CPU/system temperature

 Monitors ±1 V/±5V/3.3V/CPU/VBAT(V)/5VSB(V) voltages

 Monitors CPU/chassis fan speed

 Automatic chassis fan on/off control

 Read back capability that displays temperature, voltage and fan

speed

Refer to the PC Health Status section in chapter 3 and the

Hardware Monitor section in chapter 4 for more information.

1.1.3 Intelligence

CPU Temperature Protection

The CPU Temperature Protection function has the capability of

monitoring the CPUs temperature during system boot-up. Once it

has detected that the CPUs temperature exceeded the CPU

temperature limit defined in the BIOS, the system will automatically

power-off after 5 warning beeps. Refer to CPU Temp. Prot. Function

and CPU Temp. Prot. Alarm in the PC Health Status section in

chapter 3 for more information.

Otros manuales para AD73 Pro

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de DFI

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario