DFI KS156-AL Manual de usuario

KS156-AL Installation Guide

DFI reserves the right to change the specications at any time prior to

the product's release. For the latest revision and more details of the

installation procedure, please refer to the user's manual on the website.

www.d.com

• 15.6" 1366x768 TFT LCD Panel with Touch Screen

• 1x 2.5" SATA drive bay

• IP65 Front Panel Protection

• VESA/Panel Mount

• Rich I/O: 2 LAN, 2 COM, and 4 USB 3.0

Features

Panel

Rear View

Bottom View

Power Button HDMI

COM 1

(RS232/RS422/RS485)

COM 2

(RS232/RS422/RS485)

USB 3.0

VGA LAN1 LAN2

Removing the Chassis Cover

1. Make sure the system and all other peripheral devices connected to it

have been powered off.

2. Disconnect all power cords and cables.

3. The 6 mounting screws on the rear chassis are used to secure the cover

to the system. Remove these screws and put them in a safe place for

later use.

4. Lift the cover up to open the system.

5. The

SODIMM,

Mini PCIe and the M.2 sockets are readily accessible

after removing the chassis cover.

Screws

SODIMM Slot

Mini PCIe Slot

M.2 Socket

Installing a SATA drive

1. Uninstall the SATA mount bracket from the system. Align the mounting

holes of the SATA drive with the mounting holes on the SATA mount

bracket and use the provided mounting screws to attach the SATA drive

to the bracket.

2. Connect one end of the SATA cable to the SATA power and data

connectors on the SATA drive and the other end of the SATA cable to

the SATA power and data connectors on the system board.

3. Align the mounting holes of the SATA mount bracket with the mounting

holes on the system and use the provided mounting screws to secure

the SATA mount bracket in place.

The system can accommondate one 2.5-inch SATA drive. Please use the

following procedure to install a SATA drive.

Mounting screw

SATA connectors

SATA power/data cable

Note:

The SATA Port 1 shares the bandwidth with the M.2 slot. To assign the SATA bandwidth to

the SATA Port 1 or the M.2 slot, refer to "Board Layout and Jumper Settings."

SATA mount screws

Installing an M.2 Card

The system is equipped with one M.2 socket, supporting both the M.2

22x42mm and 22x80mm (key B) form factors. Use the following procedure

to install an M.2 card:

1. To install an M.2 type 2242 card, please install the standoff at the 42mm

mounting position rst.

M.2 card

M.2 Type 2242 Socket

2. Align the notch at the edge of the M.2 card with the key in the

connector.

3. Insert the M.2 card into the connector.

M.2 mount standoff

M.2 Type 2280 Socket

Note:

The M.2 socket supports PCIe, USB, and SATA signals and can accommodate common

mobile broadband and storage modules. For jumper settings on switching the signal

betwen SATA and PCIe, refer to "Board Layout and Jumper Settings."

3. Push down on the other end of the M.2 card and secure the card on the

mainboard with the provided mounting screw.

M.2 card

Mounting screw

Installing a Mini PCIe Card

The system board is equipped with one Mini PCIe slot that supports PCIe

and USB signals. Use the following procedure to install a Mini PCIe card:

1. Grasp the Mini PCIe card by its edges and align the notch in the

connector of the PCIe card with the key in the connector on the

system board.

2. Push the Mini PCIe card down and use the provided mounting screws

to secure the card on the system board. Route the antenna cable

underneaqth the SATA bracket.

Mini PCIe card

Mounting screw

Antenna Hole

The VESA mount kit includes the following:

• 2 VESA mount brackets

• Bracket screws

Please use the following procedure to mount your system:

1. Select a place on the wall where you will mount the Panel PC.

2. Use the provided mounting screws to attach “VESA mount bracket 1” to

the wall.

Mounting Options

VESA mount

VESA mount bracket 1

Mounting screw

VESA mount bracket 2

VESA mount bracket 1

3. Attach the other bracket (VESA mount bracket 2) to the rear of

the Panel PC.

4. Slide the Panel PC to "VESA mount bracket 1" to attach the two brackets

with the hooks. Then tighten the screw to secure the assembly in place.

Screw

VESA mount bracket 2

Mounting screw

Hooks

Please use the following procedure to mount your system:

1. Select a place on the panel (or wall) where you will mount the Panel PC.

2. Cut out a shape on the panel that corresponds to the Panel PC’s rear

dimensions (396.2mm x 246.5mm) and ensure that the Panel PC can be

tted into the panel properly.

3. Insert the Panel PC from the outside surface of the panel into the

mounting hole until it is properly tted against the panel.

4. Position the mounting clamps along the rear edges of the Panel PC and

insert them into the slits around the Panel PC.

Panel mount

The panel mounting kit includes the following:

• 10 mounting clamps

Panel

Mounting hole

396.20

246.50

R10.90

272.30

422

16 (x10)

4 (Max)

Front view

Otros manuales para KS156-AL

Tabla de contenidos

Otros manuales de PC industrial de DFI

Manuales populares de PC industrial de otras marcas

Chipsee

Chipsee PPC-A72-101 Manual de usuario

Advantech

Advantech UNO-2184G Manual de usuario

MSI

MSI MS-9A76 Manual de usuario

Stackrack

Stackrack THOR200 Manual de usuario

Moxa Technologies

Moxa Technologies DA-682C Series Manual de usuario

Nodka

Nodka eBOX-3000-ETC Manual de usuario

Siemens

Siemens SIMATIC IPC627E Manual de usuario

MSI

MSI MS-9A89 Manual de usuario

Artila

Artila Matrix-516 Manual de usuario

Siemens

Siemens SIMATIC Rack PC 840 V2 Manual de usuario

Advantech

Advantech IPPC-6152A Manual de usuario

Beckhoff

Beckhoff CX9020 Manual de usuario

Dell

Dell Embedded Box PC 5000 Manual de usuario

IBASE Technology

IBASE Technology ASB200-918 Series Manual de usuario

Lenovo

Lenovo ThinkCentre M90q Manual del propietario

IXXAT

IXXAT Econ 100 Manual de usuario

Kontron

Kontron KBox A-151-TGL Manual de usuario

AXIOMTEK

AXIOMTEK ICO500-518 Series Manual de usuario