DFI ES220F-CS Manual de usuario

© May 12, 2023 DFI Inc.

www.dfi.com

ES220F-CS

Compact Fanless Embedded System

Quick Installation Guide

Package Contents

• 1 ES220F-CS system unit with wallmount

• Adapter 12V 60W (optional)

• Power Cord 1830mm (optional)

• VESA mounting kit (optional)

Quick Reference | ES220F-CS 1

Product Overview

Front View - 1 storage

Front View - 3 storage

1

2

3

4

5

Power Button

Status LED, Reset Button

HDMI 2.0

USB 3.1

LAN 1 & LAN 2

2

1345

2

1345

Quick Reference | ES220F-CS 2

Rear View - 1 storage

Rear View - 3 storage

6

78910

6

78910

8

9

10

Grounding Hole

COM 1

COM 2

USB 2.0

DC-in

6

7

Removing the Chassis Cover

Please observe the following guidelines and follow the instructions to open the system.

1.

Make sure the system and all other peripheral devices connected to it have been

powered off.

2. Disconnect all power cords and cables.

Step 1:

To remove the top cover - The 8 screws on the top of the system

are used to secure the

cover

to

the

chassis. Remove the screws and put them in a safe place for later use. And then lift up

the cover to remove it.

To remove the bottom cover - The 2 screws on the bottom of the system

are used to secure

the

cover

to

the

chassis. Remove the screws and put them in a safe place for later use. And

then tilt up the cover to remove it.

Bottom ViewTop View

Step 2:

Lift the cover to open the system.

Quick Reference | ES220F-CS 3

Step 3:

The board can be easily accessed after the chassis cover is removed.

Bottom View

Top View

Quick Reference | ES220F-CS 4

Installing an M.2 Card

Please observe the following guidelines and follow the instructions to open the system.

1.

Make sure the system and all other peripheral devices connected to it have been

powered off.

2. Disconnect all power cords and cables.

Step 1:

The 2 screws on the bottom of the system

are used to secure the

cover

to

the

chassis.

Remove the screws and put them in a safe place for later use.

Lift the cover to open the system. M.2 card slots can be easily accessed after the chassis

cover is removed.

M.2-M

M.2-E

Quick Reference | ES220F-CS 5

M.2 Module M.2 Socket

Key

Stand-off

Notch

Step 4:

Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap

between the card and the stand-off closes up. The card should be lying parallel to the board

when it’s correctly mounted.

Step 3:

Press the end of the card far from the socket down until against the stand-off.

M.2 Module M.2 Socket

Key

Stand-off

Notch

M.2 Module M.2 Socket

Key

Stand-off

Notch

Step 2:

Please follow the steps below to install the card into the socket.

Insert the card into the socket at an angle while making sure the notch and key are perfectly

aligned.

Quick Reference | ES220F-CS 6

Before installing the antenna, please make sure that the following safety cautions are

wellattended

.

1. Make sure the PC and all other peripheral devices connected to it have been

powered

down

.

2. Disconnect all power cords and cables.

Step 1:

There are antenna holes reserved on the front and back side of the system and covered by 4

knockout tabs. Please remove the knockout tabs prior to installing an antenna.

Knockout tabs for Antenna Hole

Knockout tabs for Antenna Hole

Installing an Antenna

Quick Reference | ES220F-CS 7

Step 2:

Use a flathead screwdriver and apply a little extra force to detach a knockout tab until it breaks

off from the system.

Once the knockout tab is mostly detached, it will pretty quickly snap off, leaving you a nice hole

for installing an antenna.

Step 3:

Connect the internal cable to the board's antenna connector, screw the antenna connector

through the antenna hole with washers and nuts, and screw on the antenna as illustrated

below.

Antenna ConnectorCableModule Connector NutWasher

Chassis Wall Antenna

Quick Reference | ES220F-CS 8

Wall Mount

The wall mount kit containing two mounting brackets — purchased as optional items — can

be attached to the bottom of the system for mounting onto desired locations, such as walls,

stands, or shelves. Locate the mounting holes on the bottom of the system as shown in the

photo. Screw on the two brackets onto the system with four screws as illustrated below.

Wall Mount Bracket

Wall Mount Bracket

ES220F-CS 1 storage as an example:

Quick Reference | ES220F-CS 9

Otros manuales para ES220F-CS

1

Tabla de contenidos

Otros manuales de PC industrial de DFI

Manuales populares de PC industrial de otras marcas

Chipsee

Chipsee PPC-A72-101 Manual de usuario

Advantech

Advantech UNO-2184G Manual de usuario

MSI

MSI MS-9A76 Manual de usuario

Stackrack

Stackrack THOR200 Manual de usuario

Moxa Technologies

Moxa Technologies DA-682C Series Manual de usuario

Nodka

Nodka eBOX-3000-ETC Manual de usuario

Siemens

Siemens SIMATIC IPC627E Manual de usuario

MSI

MSI MS-9A89 Manual de usuario

Artila

Artila Matrix-516 Manual de usuario

Siemens

Siemens SIMATIC Rack PC 840 V2 Manual de usuario

Advantech

Advantech IPPC-6152A Manual de usuario

Beckhoff

Beckhoff CX9020 Manual de usuario

Dell

Dell Embedded Box PC 5000 Manual de usuario

IBASE Technology

IBASE Technology ASB200-918 Series Manual de usuario

Lenovo

Lenovo ThinkCentre M90q Manual del propietario

IXXAT

IXXAT Econ 100 Manual de usuario

Kontron

Kontron KBox A-151-TGL Manual de usuario

AXIOMTEK

AXIOMTEK ICO500-518 Series Manual de usuario