DF ROBOT TEL0070 Manual de usuario
7/10/2014 Multi USB/RS232/RS485/TTL Converter (SKU:TEL0070) - Robot Wiki
http://www.dfrobot.com/wiki/index.php/Multi_USB/RS232/RS485/TTL_Converter_(SKU:TEL0070) 1/6
Multiplexer (SKU:TEL0070)
Multi USB/RS232/RS485/TTL Converter (SKU:TEL0070)
From Robot Wiki
Contents
1 Introduction
2 Power Supply
3 PIN Function Description
4 Usage Direction
5 Other Reference Connection
Introduction
Multiplexer is a multi protocol converter which is composed by multiple
interfaces for using controller communication. Multiplexer supports
conversion interfaces among USB, TTL, RS232, RS485, and allows to
have one input and multiple outputs. It's more convenient for many
kinds of controllers to communication.
Power Supply
Supply Voltage is 5V ，and is divided into two way.
1. via Micro USB data wire.
2. Any pin 5V .
Note：please do not plug two or more 5V to aviod to burn the chip. And, do not connect 5V if already connected
from Micro USB.
PIN Function Description
Points to note:
1. Multiplexer board is divided into Area A and Area B. Area A includes Micro USB、ATTL and A232 interfaces. Area
B includes BTTL、B232、B485 interfaces. The signal can be convertered between A and B.
2. The signal in the same area can't be convertered. For example, ATTL can't be converted to A232, but it can be
convertered to B232.
3. Only one input in the same area, but it allows to have multiple outputs.For example，if micro USB interface in A is
input，multiplexer can be allowed to have 232、485 and TTL as outputs.
Indicator：
POWER:power indicator
AR->BT: The interface in A as input，the interface in B as output
BR->AT: The interface in B as input, the interface in A as output
7/10/2014 Multi USB/RS232/RS485/TTL Converter (SKU:TEL0070) - Robot Wiki
http://www.dfrobot.com/wiki/index.php/Multi_USB/RS232/RS485/TTL_Converter_(SKU:TEL0070) 2/6
Usage Direction
Sample descripition:
The multiplexer board achieve USB to TTL, micro USB interface in A as input and the TTL interface in B as output. The
operation is same for USB to 232 and 485.Similarly, the reverse converter B to A is also feasible,such as 232 to USB,485 to
USB, TTL to USB.
STEP 1：Hardware Requirements
1. DFRduino UNO R3 (http://www.dfrobot.com/index.php?
route=product/product&filter_name=UNO&product_id=838#.UmDxA8ZpnMs)
2. USB Cable A-B for Arduino (http://www.dfrobot.com/index.php?
route=product/product&filter_name=usb&product_id=134#.UmDxVsZpnMs)
3. Micro USB Cable (http://www.dfrobot.com/index.php?
route=product/product&filter_name=usb&product_id=770#.UmDxU8ZpnMs)
4. Arduino Jumper Cables (http://www.dfrobot.com/index.php?
route=product/product&path=44_86&product_id=130#.UmDxxsZpnMs)
STEP 2：Connection
1. Plugin Micro USB cable to multiplexer board. The "POWER" LED turns on at the same time.
2. Multiplexer need to install driver before you use. Driver installed completed, please open Control Panel -- Device
Manager in your PC. You will see a new port.
driver download (http://www.ftdichip.com/Drivers/VCP.htm)
3. According to the following connection diagram，connect it.
4.Plugin the A to B USB to UNO
7/10/2014 Multi USB/RS232/RS485/TTL Converter (SKU:TEL0070) - Robot Wiki
http://www.dfrobot.com/wiki/index.php/Multi_USB/RS232/RS485/TTL_Converter_(SKU:TEL0070) 3/6
STEP 3: Program a sample code for your Arduino UNO
?
1
2
3
4
5
6
7
8
9
10
void setup()
{
Serial.begin(115200);
}
void loop()
{
if(Serial.available()){
Serial.write(Serial.read());
}
}
STEP 4： Send and Receive data
We need a serial monitor for monitoring data. There're lots of good tools like putty,CoolTerm and so on.In this case, we
choose CoolTerm (http://freeware.the-meiers.org/) to do this.
Please set the baud rate to 115200 bps and com port.Back to the main interface, click Connection--Send String, the
following dialog will open.
You can send the string in this dialog. The string received can be showed in the other port(UNO port).
7/10/2014 Multi USB/RS232/RS485/TTL Converter (SKU:TEL0070) - Robot Wiki
http://www.dfrobot.com/wiki/index.php/Multi_USB/RS232/RS485/TTL_Converter_(SKU:TEL0070) 4/6
Thus far，you achieve the function USB to TTL.
However, you can test reversed converter based on this function, being B to A converter. You only need to change the UNO
code. You will see the change that coolterm will receive data from UNO.
Refer to the test code：
?
1
2
3
4
5
6
7
8
9
10
void setup()
{
Serial.begin(115200);
}
void loop()
{
Serial.print("Hello,DFRobot！");
Serial.println();
delay(500);
}
Other Reference Connection
1.TTL to 232 converter
7/10/2014 Multi USB/RS232/RS485/TTL Converter (SKU:TEL0070) - Robot Wiki
http://www.dfrobot.com/wiki/index.php/Multi_USB/RS232/RS485/TTL_Converter_(SKU:TEL0070) 6/6
Retrieved from "http://www.dfrobot.com/wiki/index.php?
title=Multi_USB/RS232/RS485/TTL_Converter_(SKU:TEL0070)&oldid=7410"
This page was last modified on 18 October 2013, at 16:33.
This page has been accessed 1,811 times.
Tabla de contenidos
Otros manuales de Robótica de DF ROBOT
DF ROBOT
DF ROBOT Robot Beginner Kit with Arduino Manual de usuario
DF ROBOT
DF ROBOT Flamewheel Robot Manual de usuario
DF ROBOT
DF ROBOT ROB0118 Manual de usuario
DF ROBOT
DF ROBOT DEVASTATOR Manual de usuario
DF ROBOT
DF ROBOT HCR Manual de usuario
DF ROBOT
DF ROBOT Cherokey 4WD Basic Kit Manual de usuario
DF ROBOT
DF ROBOT Insectbot Hexa Manual de programación
DF ROBOT
DF ROBOT MiniQ II Manual de usuario
DF ROBOT
DF ROBOT MAX:BOT Manual de usuario
DF ROBOT
DF ROBOT MBT0021-EN Manual de usuario
Manuales populares de Robótica de otras marcas
STEMCenter USA
STEMCenter USA Pi-Bot v2.00 Manual de usuario
SunFounder
SunFounder PiDog Manual de usuario
Universal Robots
Universal Robots UR5 Manual de usuario
Universal Robots
Universal Robots E Series Manual de usuario
YASKAWA
YASKAWA MOTOMAN-MPL80 II Manual de usuario
EFORT
EFORT ECR5 Manual de instrucciones
