Dexter Laundry T-300 VENDED Manual de usuario

8514-296-001 REV A page 1

COMMERCIAL WASHERS

MODELS

T-300/350/400/450/600/650/750/900/950/1200/1450

VENDED C-SERIES CONTROL

OPERATOR’S MANUAL

INSTALLATION & OPERATION

INSTRUCTIONS

Please read this information and retain for reference

WARNIN - THIS WASHER IS EQUIPPED WITH DEVICES AND FEATURES RELATING TO ITS SAFE

OPERATION TO AVOID INJURY OR ELECTRICAL SHOCK, DO NOT PERFORM ANY SERVICING UNLESS

QUALIFIED TO DO SO

IT IS THE RESPONSIBILITY OF THE OWNER TO CHECK THIS EQUIPMENT ON A FREQUENT

BASIS TO ASSURE ITS SAFE OPERATION

A machine should NOT be allowed to operate if any of the following occur:

- Excessively high water level

- If machine is not connected to a properly grounded circuit

- If the door does not remain securely locked during the entire cycle

- Vibration or shaking from an inadequate mounting or foundation

WARNIN - SAFETY PRECAUTIONS

- Always shut off power and water supply before servicing

- Do not overload the washer

- Do not open door when cylinder is in motion or it contains water

- Do not bypass any safety devices of this washer

- Do not use volatile or flammable substances in or near this washer

- Keep all panels in place They protect against shock and injury and add rigidity to the washer

PREVENTIVE MAINTENANCE REQUIREMENTS

DAILY

- Check that the loading door remains securely locked and cannot be opened during an entire

cycle

- Check the water connections for leaks

- Clean the top, front, and sides of the cabinet to remove residue

- Clean the soap dispenser and lid and check that all dispenser mounting screws are in-place and

tight

- Check the drain valve for leaking and that it opens properly

- Check the loading door for leaks Clean the door seal of all foreign matter

- Leave the loading door open to aerate the washer when not in use

QUARTERLY

- Make sure the washer is inoperative by switching off the main power supply

- Check the V-belts for wear and proper tension

- Clean lint and other foreign matter from around motor

- Check all water connections for leaks

- Wipe and clean the inside of the washer and check that all electrical components are free of

moisture and dust

- Remove and clean water inlet hose filters Replace if necessary

- Check anchor bolts Retighten if necessary

IMPORTANT: Replace any and all panels that were removed to perform daily and/or quarterly

maintenance

8514-296-001 REV A page 2

TABLE OF CONTENTS

WASHER SPECIFICATION SHEET 4

1 1

Standard Washers 4

1 2

Express Washers 5

INSTALLATION INSTRUCTIONS 6

2 1

FOUNDATION REQUIREMENTS 6

2 2

MOUNTING 6

2 2 1

T-300 Machine Mounting Detail 8

2 2 2

T-300 Commercial Washer Dimensions 9

2 2 3

T-350 Machine Mounting Detail 10

2 2 4

T-350 Commercial Washer Dimensions 11

2 2 5

T-400 Machine Mounting Detail 12

2 2 6

T-400 Commercial Washer Dimensions 13

2 2 7

T-450 Machine Mounting Detail 14

2 2 8

T-450 Commercial Washer Dimensions 15

2 2 9

T-600 Machine Mounting Detail 16

2 2 10

T-600 Commercial Washer Dimensions 17

2 2 11

T-650 Machine Mounting Detail 18

2 2 12

T-650 Commercial Washer Dimensions 19

2 2 13

T-750 Machine Mounting Detail 20

2 2 14

T-750 Commercial Washer Dimensions 21

2 2 15

T-900/950 Machine Mounting Detail 22

2 2 16

T-900/950 Commercial Washer Dimensions 23

2 2 17

T-1200 Machine Mounting Detail 24

2 2 18

T-1200 Commercial Washer Dimensions 25

2 2 19

T-1450 Machine Mounting Detail 26

2 2 20

T-1450 Commercial Washer Dimensions 27

2 3

PLUMBING 28

2 4

DRAIN 28

2 5

PROTECTIVE FILM 28

2 6

ELECTRICAL 28

2 6 1

INSTALLING THE ELECTRICAL CONNECTION 30

2 6 2

FUSING REQUIREMENTS 30

2 6 3

CONTROLS TRANSFORMER (208-240V 60 Hz models only) 31

2 6 4

CONTROLS TRANSFORMER (230V 50 Hz models only) 31

2 7

OPERATION CHECK 32

OPERATING INSTRUCTIONS 33

8514-296-001 REV A page 3

3 1

STARTING THE WASHER 33

3 2

END OF CYCLE 34

3 3

EMERGENCY STOP / SAFETY DOOR LOCK 34

3 4

VARIABLE FREQUENCY DRIVE INDICATORS 35

MACHINE PROGRAMMING INSTRUCTIONS 36

4 1

MANUAL PROGRAMMING: 36

4 2

Optional Cycles Option: 39

4 3

Error Code Historical Log: 40

4 4

Prices Option: 40

4 5

Temp Pricing Option: 41

4 6

Cycles Option: 41

4 7

Plus Cycle Options: 44

4 8

Settings: 47

4 9

Usage Menu: 50

4 10

Control Menu: 52

4 11

COIN WASHER DEFAULT CYCLE 53

4 12

WASHERS WITHOUT COIN ACCEPTORS 53

4 13

RAPID ADVANCE MODE 53

4 14

WATER LEVEL ADJUSTMENT 54

DISPLAYED WASHER MESSAGES 55

TROUBLESHOOTING 63

TRANSIENT VOLTAGE SURGE SUPPRESSORS 67

SERVICE AND PARTS 68

8514-296-001 REV A page 4

1 WASHER SPECIFICATION SHEET

1 1 Standard Washers

Capacity Dry Weight Capacity - lb (kg) 20 (9.1) 30 (13.6) 40 (18.1) 60 (27.2) 80 (36.3)

Cylin er Volume - cu ft (L) 2.7 (76.5) 4 (113.3) 6 (170) 9 (254.9) 11.5 (325.6)

Spee High Extract Spee - g (RPM) 100 (579) 100 (532) 100 (532) 100 (485) 100 (485)

Interme iate Extract Spee - g (RPM) 60 (449) 60 (412) 60 (412) 60 (375) 60 (375)

Washing Spee - g (RPM) 0.9 (55) 0.9 (50) 0.9 (50) 0.9 (43) 0.9 (43)

Motor Size - hp (kW) 1 (0.75) 2 (1.5) 2 (1.5) 3 (2.2) 3 (2.2)

Dimensions Cabinet Height - in (cm) 43 7/8 (111.4) 48 3/16 (122.4) 49 11/16 (126.2) 55 3/8 (140.7) 57 7/8 (147)

Cabinet Wi th - in (cm) 26 (66) 29 7/8 (75.9) 29 7/8 (75.9) 34 3/8 (87.3) 34 3/8 (87.3)

Cabinet Depth - in (cm) 25 (63.5) 27 3/8 (69.5) 36 (91.4) 38 7/8 (98.8) 45 3/8 (115.3)

Door Opening - in (cm) 12 1/4 (31.1) 15 1/4 (38.7) 15 1/4 (38.7) 19 1/4 (48.9) 19 1/4 (48.9)

Floor to Door Bottom - in (cm) 14 7/8 (37.8) 16 1/4 (41.3) 16 1/4 (41.3) 16 (40.6) 18 1/2 (47)

Cylin er Diameter - in (cm) 21 (53.3) 25 (63.5) 25 (63.5) 30 (76.2) 30 (76.2)

Cylin er Depth - in (cm) 13 1/2 (34.3) 14 1/8 (35.9) 21 1/8 (53.7) 22 (55.9) 28 (71.1)

Weight Net Weight - lb (kg) 317 (143.8) 432 (196) 558 (253.1) 964 (437.3) 1022 (463.6)

Shipping Shipping Weight - lb (kg) 340 (154.2) 450 (204.1) 580 (263.1) 980 (444.5) 1063 (482.2)

Shipping Height - in (cm) 50 (127) 53 1/4 (135.3) 54 3/4 (139.1) 61 1/2 (156.2) 63 3/4 (161.9)

Shipping Wi th - in (cm) 27 1/4 (69.2) 31 1/2 (80) 31 1/2 (80) 36 (91.4) 36 (91.4)

Shipping Depth - in (cm) 30 1/2 (77.5) 33 1/2 (85.1) 41 (104.1) 44 1/4 (112.4) 52 3/16 (132.6)

Water Water Inlet Size - in (mm) 3/4 (19) 3/4 (19) 3/4 (19) 3/4 (19) 3/4 (19)

Pressure (min-max) - psi (kPa) 30-120 (207-827) 30-120 (207-827) 30-120 (207-827) 30-120 (207-827) 30-120 (207-827)

Flow Rate - gal/min (L/min) 9 (34) 9 (34) 9 (34) 9 (34) 9 & 12 (34 & 45)

Approx. Water Usage Per Cycle - gal (L)

15.8

(59.8)

23.5

(89)

35.1

(132.9)

52.6

(199.1)

(253.6)

Drain Diameter (O.D.) - in (cm)

2 1/4

(5.7)

(7.6)

Floor to Center of Drain - in (cm)

(15.2)

4 11/16

(11.9)

(12.7)

6 5/8

(16.8)

8 5/8

(21.8)

Electrical

Mo el

Volts / Hz / Phase / Wiring

-10

120 / 60 / 1 / Provi e

208-240 / 60 / 1 / 2 wire + groun

208-240 / 60 / 3 / 3 wire + groun

-39 230 / 50 / 1 / 2 wire + groun

Installation

Min. Clearance Between Machines - in (cm)

1/2

(1.3)

1/2

(1.3)

1/2

(1.3)

1/2

(1.3)

1/2

(1.3)

Min. Clearance Behin Machines - in (cm

(61)

Min. Concrete Thickness - in (cm) 6 (15.2) 6 (15.2) 6 (15.2) 8 (20.3) 8 (20.3)

15 / 6.2 / 3.5 mm²

---

20 / 8.4 / 3.5 mm²

---

20 / 8.4 / 3.5 mm²

15 / 6.2 amp / #12 20 / 8.4 / #12 20 / 8.4 / #12

15 / 4 / 3.5 mm²

---

15 / 6.2 / 3.5 mm²

15 / 4 / #12 15 / 6.2 / #12-12

Circuit Breaker Amps / Running Amps / Wire Size

T-300

T-400

T-600

T-900

T-1200

20 / 13 / Provi e

---

8514-296-001 REV A page 5

1 2 Express Washers

Capacity Dry Weight Capacity - lb (kg) 20 (9.1) 30 (13.6) 40 (18.1) 50 (22.7) 60 (27.2) 90 (40.8)

Cylin er Volume - cu ft (L) 2.7 (76.5) 3.8 (107.6) 6 (170) 6.5 (184.1) 9 (254.9) 13.7 (388)

Spee High Extract Spee - g (RPM) 200 (819) 200 (750) 200 (750) 200 (685) 200 (685) 200 (617)

Interme iate Extract Spee - g (RPM) 60 (449) 60 (411) 60 (411) 60 (375) 60 (375) 60 (338)

Washing Spee - g (RPM) 0.9 (55) 0.9 (50) 0.9 (50) 0.9 (43) 0.9 (43) 0.9 (39)

Motor Size - hp (kW) 1 (0.75) 2 (1.5) 2 (1.5) 3 (2.2) 3 (2.2) 6.7 (5)

Dimensions Cabinet Height - in (cm) 43 7/8 (111.4) 48 3/16 (122.4) 53 (134.6) 53 7/8 (136.9) 55 3/8 (140.7) 62 3/8 (158.4)

Cabinet Wi th - in (cm) 26 (66) 29 7/8 (75.9) 29 7/8 (75.9) 34 3/8 (87.3) 34 3/8 (87.3) 41 1/2 (105.4)

Cabinet Depth - in (cm) 28 (71.1) 28 1/4 (71.8) 38 1/8 (96.8) 32 7/8 (83.5) 38 7/8 (98.7) 42 1/4 (107.3)

Door Opening - in (cm) 12 1/4 (31.1) 15 1/4 (38.7) 15 1/4 (38.7) 19 1/4 (48.9) 19 1/4 (48.9) 19 1/4 (48.9)

Floor to Door Bottom - in (cm) 14 7/8 (37.8) 16 1/4 (41.3) 16 1/4 (41.3) 16 (40.6) 16 (40.6) 19 5/16 (49.1)

Cylin er Diameter - in (cm) 21 (53.3) 25 (63.5) 25 (63.5) 30 (76.2) 30 (76.2) 37 (94)

Cylin er Depth - in (cm) 13 1/2 (34.3) 13 3/8 (34) 21 1/8 (53.7) 16 (40.6) 22 (55.9) 22 (55.9)

Weight Net Weight - lb (kg) 383 (173.7) 526 (238.6) 744 (337.5) 920 (417.3) 1000 (453.6) 1322 (599.6)

Shipping Shipping Weight - lb (kg) 407 (184.6) 544 (246.8) 766 (347.5) 947 (429.6) 1016 (460.8) 1364 (618.7)

Shipping Height - in (cm) 49 1/4 (125.1) 53 1/4 (135.3) 58 3/4 (149.2) 60 (152.4) 61 1/2 (156.2) 69 1/4 (175.9)

Shipping Wi th - in (cm) 28 1/4 (71.8) 31 1/2 (80) 31 1/2 (80) 36 (91.4) 36 (91.4) 43 1/8 (109.5)

Shipping Depth - in (cm) 33 1/2 (85.1) 33 1/2 (85.1) 43 3/4 (111.1) 38 (96.5) 45 1/4 (114.9) 48 (121.9)

Water Water Inlet Size - in (mm) 3/4 (19) 3/4 (19) 3/4 (19) 3/4 (19) 3/4 (19) 3/4 (19)

Pressure (min-max) - psi (kPa) 30-120 (207-827) 30-120 (207-827) 30-120 (207-827) 30-120 (207-827) 30-120 (207-827) 30-120 (207-827)

Flow Rate - gal/min (L/min) 9 (34) 9 (34) 9 (34) 9 (34) 9 & 12 (34 & 45) 9 & 12 (34 & 45)

Approx. Water Usage Per - gal (L)

15.8

(59.8)

22.2

(84)

35.1

(132.9)

38.4

(145.4)

52.6

(199.1)

80.1

(303.2)

Drain Diameter (O.D.) - in (cm)

2 1/4

(5.7)

(7.6)

Floor to Center of Drain - in (cm)

(15.2)

(12.7)

6 7/8

(17.5)

6 5/8

(16.8)

6 5/8

(16.8)

5/16

(21.1)

Electrical

Mo el

Volts / Hz / Phase / Wiring

-10

120 / 60 / 1 / Provi e

208-240 / 60 / 1 / 2 wire + groun

208-240 / 60 / 3 / 3 wire + groun

-39 230 / 50 / 1 / 2 wire + groun

Installation

Min. Clearance Between Machines - in (cm)

1/2

(1.3)

1/2

(1.3)

1/2

(1.3)

1/2

(1.3)

1/2

(1.3)

1/2

(1.3)

Min. Clearance Behin Machines - in (cm

(61)

Min. Concrete Thickness - in (cm)

(15.2)

(20.3)

(30.5)

Circuit Breaker Amps / Running Amps / Wire Size

T-750

T-350

T-450

T-650

T-950

T-1450

15 / 6.2 / #12

---

15 / 6.2 / 3.5 mm

---

15 / 6.2 / 3.5 mm²

15 / 6.2 / #12 15 / 6.2 / #12-12 30 / 15 / #10

---

20 / 8.4 / 3.5 mm²

---

30 / 15 / 5.3 mm²

20/ 8.4 / #12 20/ 12 / #12

---

15 / 6.2 / 3.5 mm²

---

20 / 12 / 3.5 mm²

8514-296-001 REV A page 6

2 INSTALLATION INSTRUCTIONS

All washers must be installed in accordance with all local, state and national

building, electrical, plumbing and other codes in effect in the area

WARNIN :

THESE INSTALLATION AND SERVICIN INSTRUCTIONS ARE FOR USE

BY QUALIFIED PERSONNEL ONLY. TO AVOID INJURY AND ELECTRICAL

SHOCK, DO NOT PERFORM ANY SERVICIN OTHER THAN THAT

CONTAINED IN THE OPERATIN INSTRUCTIONS, UNLESS QUALIFIED.

2 1 FOUNDATION REQUIREMENTS

T-300, 400, 600:

This machine is designed for use on or over bare concrete floor - not to be

used above combustible flooring, such as carpet or wood The washer

must be securely bolted to a substantial concrete floor, or mounted upon

a suitable base that is securely bolted to a substantial concrete floor

T-350, 450, 650, 750, 900, 950, 1200, 1450:

This machine is designed for use on or over bare concrete floor - not to be

used above combustible flooring, such as carpet or wood The washer

must be securely bolted and grouted to a substantial concrete floor, or

mounted and grouted upon a suitable base that is securely bolted and

grouted to a substantial concrete floor

CARE MUST BE TAKEN WITH ALL FOUNDATION WORK TO ENSURE A

STABLE UNIT INSTALLATION, ELIMINATING POSSIBILITIES OF

EXCESSIVE VIBRATION

All installations require concrete floors and quality grade anchor bolts or

expansion anchors Mounting hardware is not provided with the

machines Refer to appropriate model Machine Mounting Detail Figures 1-

1, 1-2 and 1-3 for floor thickness and bolt sizes See mounting diagram

for overall washer dimensions

2 2 MOUNTING

A concrete pedestal or steel-mounting base that elevates the machine

above the floor level is recommended to provide easy access to the

loading door

Recommended height:

T-300/350: approximately 8 inches (200 mm)

T-400/450/600: approximately 6 inches (152 mm)

T-650/750/900/950/1200/1450: approximately 4 inches (102 mm)

Allow a minimum 24 inches (610 mm) of clearance behind the rear of the

machine to provide access for motor service Contact a Dexter laundry

equipment distributor for recommended steel mounting bases

8514-296-001 REV A page 7

If an elevated concrete pedestal is desired, it should be embedded and

tied into the existing floor (cut through existing floor as shown) See

Machine Mounting Detail Figures for floor thickness and bolt sizes

EXPANSION ANCHORS ARE NOT RECOMMENDED FOR USE IN CONCRETE

PEDESTALS BECAUSE THE ANCHORS ARE TOO CLOSE TO AN EDGE,

CAUSING IT TO BREAK OUT

8514-296-001 REV A page 8

2 2 1

T-300 Machine Mounting Detail

8514-296-001 REV A page 9

2 2 2

T-300 Commercial Washer Dimensions

8514-296-001 REV A page 10

2 2 3

T-350 Machine Mounting Detail

Otros manuales para T-300 VENDED

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Arandela de Dexter Laundry

Dexter Laundry

Dexter Laundry T-1450 Manual de instalación

Dexter Laundry

Dexter Laundry HIGH SPEED 25LB WASHER Instrucciones de instalación

Dexter Laundry

Dexter Laundry T-300 VENDED Manual

Dexter Laundry

Dexter Laundry T450 Express Manual de usuario

Dexter Laundry

Dexter Laundry C Series Manual de usuario

Dexter Laundry

Dexter Laundry WCVD Series Guía de inicio rápido

Dexter Laundry

Dexter Laundry T-350SWD Manual de usuario

Dexter Laundry

Dexter Laundry T-400 On-Premise Manual de usuario

Dexter Laundry

Dexter Laundry T-300 VENDED Guía de inicio rápido

Dexter Laundry

Dexter Laundry Wn0600xa-12en2x-sskcs-usx Guía de inicio rápido

Dexter Laundry

Dexter Laundry T350 Manual de usuario

Dexter Laundry

Dexter Laundry T-1800 Manual de usuario

Dexter Laundry

Dexter Laundry WCVD-WN Series Manual de usuario

Dexter Laundry

Dexter Laundry WN0675 Guía de inicio rápido

Dexter Laundry

Dexter Laundry 400 EXPRESS Manual de usuario

Dexter Laundry

Dexter Laundry T-300 VENDED Manual de usuario

Dexter Laundry

Dexter Laundry WCN Series Manual de usuario

Dexter Laundry

Dexter Laundry T-900 Guía de inicio rápido

Dexter Laundry

Dexter Laundry T-450SWD Manual de usuario

Dexter Laundry

Dexter Laundry WCAD Series Guía de inicio rápido

Dexter Laundry

Dexter Laundry V-Series Manual de usuario

Dexter Laundry

Dexter Laundry OPL 30 Cycle 200G Express Guía de inicio rápido

Dexter Laundry

Dexter Laundry T-675 EXPRESS PLUS Manual de usuario

Dexter Laundry

Dexter Laundry WC 00XA-12EC X Series Manual de usuario

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Daewoo

Daewoo DWD-F1222 Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario