Dexter Laundry T-300 VENDED Manual de usuario
8514-223-001 REV B page 1
COMMERCIAL WASHER
MODEL T-300 VENDED
C-SERIES CONTROL
OPERATOR’S MANUAL
INSTALLATION & OPERATION
INSTRUCTIONS
Please read this information and retain for reference.
WARNING - HIS WASHER IS EQUIPPED WI H DEVICES AND FEA URES RELA ING O I S SAFE
OPERA ION. O AVOID INJURY OR ELEC RICAL SHOCK, DO NO PERFORM ANY SERVICING UNLESS
QUALIFIED O DO SO.
I IS HE RESPONSIBILI Y OF HE OWNER O CHECK HIS EQUIPMEN ON A FREQUEN
BASIS O ASSURE I S SAFE OPERA ION.
A machine should not be allowed to operate if any of the following occur:
- Excessively high water level.
- If machine is not connected to a properly grounded circuit.
- If the door does not remain securely locked during the entire cycle.
- Vibration or shaking from an inadequate mounting or foundation.
WARNING - FOR SAFETY
1. Always shut off power and water supply before servicing.
2. Do not overload the washer.
3. Do not open door when cylinder is in motion or it contains water.
4. Do not bypass any safety devices of this washer.
5. Do not use volatile or flammable substances in or near this washer.
6. Keep all panels in place. hey protect against shock and injury and add rigidity to the washer.
PREVENTIVE MAINTENANCE REQUIREMENTS
DAILY
- Check that the loading door remains securely locked and cannot be opened during the entire cycle.
- Check the water connections for leaks.
- Clean the top and sides of the cabinet to remove residue.
- Clean the soap dispenser and lid and check that all dispenser mounting screws are in-place and tight.
- Check the drain valve for leaking and that it opens properly.
- Check the loading door for leaks. Clean the door seal of all foreign matter.
- Leave the loading door open to aerate the washer when not in use.
QUAR ERLY
- Make sure the washer is inoperative by switching off the main power supply.
- Check the V-belts for wear and proper tension.
- Clean lint and other foreign matter from around motor.
- Check all water connections for leaks.
- Wipe and clean the inside of the washer and check that all electrical components are free of moisture
and dust.
- Remove and clean water inlet hose filters. Replace if necessary.
- Check anchor bolts - retighten if necessary
IMPORTANT: Replace any and all panels that were removed to perform daily and/or quarterly
maintenance.
8514-223-001 REV B page 2
TABLE OF CONTENTS
Page No.
Washer Specifications 2
Mounting Dimensions 3
Installation Instructions 4
Operating Instructions 8
Programming the Washer Control 10
Displayed Washer Faults 24
Servicing and roubleshooting 30
Accessories and Contact Information 34
WASHER SPECIFICATIONS
MODEL -300 20 LB. WASHER
CAPACI Y
CYLINDER SIZE
ELEC RICAL
DRIVE SYS EM
WASH SPEED
IN ERMEDIA E
EX RAC
FINAL EX RAC
MACHINE CON ROL
WA ER INLE
DRAIN VALVE
20 LBS/2.7 CUBIC F . (9.1 kg/76.5L)
21” DIA X 13 1/2” DEEP (53cm X 34cm)
208-240 VAC, 60 HZ, 1 OR 3 PHASE or 120 VAC, 60 HZ, 1 PH
SOF S AR REVERSING INVER ER DRIVE, 1 HP MO OR
55 RPM
449 RPM (60 G’S)
579 RPM (100 G’S)
PROGRAMMABLE COMPU ER
2 SOLENOID OPERA ED VALVES
FLOW RA E: 9 GAL/MIN EACH, 30-120 PSI
2 1/4” DIAME ER (5.7 cm)
8514-223-001 REV B page 3
8514-223-001 REV B page 4
INSTALLATION INSTRUCTIONS
All washers must be installed in accordance with all local, state and national
building, electrical, plumbing and other codes in effect in the area.
WARNING - THESE INSTALLATION AND SERVICING
INSTRUCTIONS ARE FOR USE BY QUALIFIED PERSONNEL ONLY.
TO AVOID INJURY AND ELECTRICAL SHOC DO NOT PERFORM
ANY SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS, UNLESS QUALIFIED.
FOUNDA ION REQUIREMEN S
his machine is designed for use on or over bare concrete floor - not to be used above
combustible flooring. he washer must be securely bolted to a substantial concrete
floor, or mounted upon a suitable base that is securely bolted to a substantial concrete
floor. CARE MUS BE S RESSED WI H ALL FOUNDA ION WORK O INSURE A S ABLE
UNI INS ALLA ION, ELIMINA ING POSSIBILI IES OF EXCESSIVE VIBRA ION. All
installations must be made on sound concrete floors, 6 inches (150mm) or thicker.
Anchor bolts or expansion anchors must be of a quality grade and a minimum of ½ inch
(14 mm) diameter.
MOUN ING
A concrete pedestal or steel-mounting base that elevates the machine approximately 8
inches (200 mm) above the floor level is recommended to provide easy access to the
loading door. Allow a minimum of 24 inches (600mm) of clearance behind the rear of
the machine, to provide access for motor removal. Refer to Fig. 1-1 and 1-2 for
machine bolt-down dimensions.
If an elevated concrete pedestal is desired, it should be embedded into the existing
floor. Anchor bolts should be 1/2" x 8" (14 mm x 200 mm), grade 5 or better, headed
by a 4 inch (10 cm) square fish plate and should protrude 1 7/8” (48 mm) above the
finished surface of the pedestal. EXPANSION ANCHORS ARE NO RECOMMENDED FOR
USE IN CONCRE E PEDES ALS, BECAUSE HE ANCHORS ARE OO CLOSE O AN
EDGE, CAUSING I O BREAK OU . (See Fig. 1-1 and 1-3.)
8514-223-001 REV B page 5
8514-223-001 REV B page 6
PLUMBING
Water supply hoses are furnished with each machine. he threaded connections on the
hoses are ¾-11 ½ NH .
Separate hot and cold water lines must be provided, maintaining 30 psi to 120 psi (207 kPa
to 827 kPa) water flow pressure. A 140F (60C) degree hot water supply is recommended
for best washing results. Do not exceed 180F (82C) degree water temperature.
DRAIN
he drain outlet tube at the rear of the machine is 2 ¼ inches (57 mm) in diameter. Any
drain hose used must be lower than the drain valve to assure proper draining.
ELEC RICAL
WARNING
SHUT OFF POWER AND WATER BEFORE OPENING ANY SERVICE PANELS.
he Dexter -300 single-phase 115VAC 60Hz washing machines are provided with a
grounding (three-prong) power cord. A grounding receptacle must be used to provide a
good external ground to the machine.
he Dexter -300 single/three-phase 208-240VAC 60 Hz washing machines are intended to
be permanently installed appliances. No power cord is provided. he machine should be
connected to an individual branch circuit not shared by lighting or other equipment. he
connection should be sheathed in liquid tight flexible conduit, or equivalent, with
conductors of the proper size and insulation. A qualified technician should make such
connections in accordance with the wiring diagram. (Suggest a minimum wire size of 12
ga.)
Individual circuit breakers for each unit are recommended. Do not use ground-fault circuit
breakers or ground-fault circuit interrupter outlets.
O MAKE ELEC RICAL CONNEC IONS: Disconnect all power to the washer. Remove the
top panel of the washer and locate the power terminal block near the back of the control
compartment.
If power is 208-240-3PH-60Hz, connect L1, L2, L3 and ground. If there is a high leg it
must be connected to L3.
If power is 208-240-1PH-60Hz, connect L1, L2 and Ground.
NO E: It is important that the grounding screw next to the power terminal block B-
1 be connected to a good external ground.
8514-223-001 REV B page 7
FUSING REQUIREMEN S:
SINGLE-PHASE 115VAC MODELS - 20 AMP IME-DELAY (DUAL ELEMEN ) FUSE
(or equivalent circuit breaker)
SINGLE- and HREE -PHASE 208-240VAC MODELS - 15 AMP IME-DELAY (DUAL
ELEMEN ) FUSE (or equivalent circuit breaker)
CON ROLS RANSFORMER (208-240V models only)
he controls transformer is located inside the control trough and steps a range of 208 to
240 volts down to 115 volts. here are two terminals on the controls transformer for the
primary (incoming) power. Use the terminal marked “208V” for power supplies between
208 and 219 volts. Use the terminal marked “240V” for power supplies between 220 and
240 volts.
CHECKOU
After all mounting, plumbing and electrical work is completed; the washer should be run
through a cycle and checked for water leaks and proper functioning.
he cylinder should turn in a counterclockwise direction (viewed from the front of the
machine) during intermediate spin and final spin. If spin is clockwise, the 1 and 2
motor wires going to 1 and 2 on the variable frequency drive should be swapped.
Remove power to the machine before swapping wires.
8514-223-001 REV B page 8
OPERATING INSTRUCTIONS - STARTING THE WASHER
A. Load the clothes into the cylinder and latch the door securely. Be sure
clothing does not get caught between the door gasket and tub front when
closing the door. Maximum load is 20 pounds clothes, dry weight. Do not load
the washer with more than 20 lbs.
B. Select the appropriate cycle temperatures for the load being washed.
C. Add low sudsing powdered detergent into the “detergent” compartment of
the automatic dispenser on the top of the washer. If desired add fabric softener
to the “fabric softener” compartment. Use the amount of fabric softener as
recommended by the manufacturer.
If liquid wash products are used in the “detergent” compartment, they must be
added at the beginning of the wash cycle.
If the machine is set for pre-wash, washing products can be added to the round
opening of the dispenser or put in with the clothes when loading the washing
machine.
D. Insert coins, tokens or debit card to meet the displayed vend price. he
display will count down the amount needed to meet the vend price. Once the
vend price is met, the display will read “PRESS S AR ” and the start button LED
will blink. If the door is not closed and latched, the display will read “CLOSE
DOOR” and the control will wait until the door is latched to continue. Pressing the
start button will begin the cycle and activate the ON light. he display will show
the remaining cycle time in minutes. he clothes door will lock and remain
locked until the end of the cycle.
END OF CYCLE
When the cycle is complete a 3-second tone will sound and the display will read “CYCLE
DONE HANK YOU” until the door is opened. he door can now be opened. Leave the
clothes door open when the machine is not in use.
8514-223-001 REV B page 9
EMERGENCY S OP / SAFE Y DOOR LOCK
his machine is equipped with a Safety Door Lock that locks the door closed from when
the cycle is started until the cycle is complete. he door lock prevents opening the door
for up to 3 minutes if the power is interrupted during the cycle.
he Emergency Stop button pauses the washer and allows the door to be opened
during the cycle after the Safety Door Lock releases. When the Emergency Stop button
is pressed an alarm will sound and the display will begin counting down and read “S OP
3”, “S OP 2”, “S OP 1”. If the button is released before 3 seconds elapse, the alarm
will stop and the cycle will continue normally. If the Emergency Stop is held down for 3
seconds, the display will count down and the washer will begin stopping movement and
water flow and begin draining water from inside the washer. hough the machine may
stop wash movement quickly, it may take up to 3 minutes for the door to unlock.
During that time the alarm will continue to sound and the display will read “S OPPING”.
When the alarm stops, the door may be opened. he washer may be restarted by
closing and latching the door, and pressing the Start button. If the washer was stopped
more than once before the final extract, the cycle will be cancelled. If the washer was
stopped during final extract, the cycle will be ended. If the washer is stopped for more
than 1 hour, the cycle will be terminated.
8514-223-001 REV B page 10
PROGRAMMING THE WASHER CONTROL
he washer control can be programmed to prompt the user for alternate vend prices,
change washer cycle times, temperatures and many other options. his can be
accomplished in two ways:
1. Manual programming utilizing the “Start”, “Hot”, “Warm” and “Cold” buttons
2. USB download of a customizable User File. For instructions on using the USB
download feature, please contact your local Dexter distributor or visit
DexterLive.com.
MANUAL PROGRAMMING:
he washer must be in idle mode for the manual programming menus to be accessed.
Idle mode is when the washer is not actively running a wash cycle and the vend price is
displayed on the screen.
o enter the manual programming mode, the top of the washer must be unlocked and
lifted slightly (it may be necessary to remove the screws for the soap box). he
programming button is then pressed for 1 second. he control should display
“PROGRAMMING”.
See the figure below for the location of the programming button in relation to the USB
port ( he USB port is exposed when the washer top is lifted).
Otros manuales para T-300 VENDED
6
Tabla de contenidos
Otros manuales de Arandela de Dexter Laundry
Dexter Laundry
Dexter Laundry WCN Series Manual de usuario
Dexter Laundry
Dexter Laundry N-Series Manual de usuario
Dexter Laundry
Dexter Laundry T-300 VENDED Manual de usuario
Dexter Laundry
Dexter Laundry WC0300XA-10EC4X Manual de usuario
Dexter Laundry
Dexter Laundry V-Series Manual de usuario
Dexter Laundry
Dexter Laundry T-650 Guía de inicio rápido
Dexter Laundry
Dexter Laundry T-450SWD Manual de usuario
Dexter Laundry
Dexter Laundry 75LB CAPACITY COMPUTER CONTROL OPL WASHER Manual de usuario
Dexter Laundry
Dexter Laundry T-400 On-Premise Manual de usuario
Dexter Laundry
Dexter Laundry T-1800 Manual de usuario
Dexter Laundry
Dexter Laundry WCVD-WN Series Instrucciones de funcionamiento
Dexter Laundry
Dexter Laundry WCVD Series Guía del administrador
Dexter Laundry
Dexter Laundry OPL Series Guía de inicio rápido
Dexter Laundry
Dexter Laundry OPL 30 Cycle 200G Express Guía de inicio rápido
Dexter Laundry
Dexter Laundry 400 EXPRESS Manual de usuario
Dexter Laundry
Dexter Laundry WC Series Guía de inicio rápido
Dexter Laundry
Dexter Laundry T-300 VENDED Guía de inicio rápido
Dexter Laundry
Dexter Laundry WCVD-WN Series Guía de inicio rápido
Dexter Laundry
Dexter Laundry T350 Manual de usuario
Dexter Laundry
Dexter Laundry T-300 VENDED Guía de inicio rápido
