DeVilbiss GTI Manual de usuario

1 ©ITW Ltd 2000

Operation Manual

GTi – Pressure Feed Spraygun

EP 1 - 8

SB-E-2-362-C

2©ITW Ltd 2000

Declaration of Conformity

We, ITW Finishing UK, Ringwood Road Bournemouth Dorset England

declare under our sole responsibility that this product is in conformity with BS

EN 292: parts 1 and 2 :1991 and BS EN 1953:1999, following the provisions

of the Machinery Directive 89/392/EEC. This product also complies with the

requirements of the EPA guidelines, PG6/34. Transfer efficiency certificates

are available on request.

B.Holt,General Manager

Operation Manual

GTi – Pressure Feed Spraygun

Important

Read and follow all instructions and Safety Precautions before using this

equipment

Description

This product is suitable for use with both waterbased and solvent based

coating materials. The design uses EPA compliant atomising technology to

reduce overspray and improve coating efficiency.

Important: These guns are not designed for use with highly corrosive and/

or abrasive materials and if used with such materials it must be expected

that the need for cleaning and/or replacement of parts will be increased. If

there is any doubt regarding the suitability of a specific material contact

your local Distributor or ITW Finishing direct.

Model Part Number

Example: GTI-P110B-14

Aircap Fluid nozzle size

(14 = 1,4 mm)

Gunbody Finish

B= Blue Anodised

3 ©ITW Ltd 2000

SAFETY WARNINGS

Fire and explosion

Solvents and coating materials

can be highly flammable or

combustible when sprayed. ALWAYS

refer to the coating material suppliers

instructions and COSHH sheets

before using this equipment

Users must comply with all local

and national codes of practice and

insurance company requirements

governing ventilation, fire precautions,

operation and house-keeping of working

areas

This equipment, as supplied, is

NOT suitable for use with

Halogenated Hydrocarbons.

Static Electricity can be generated by

fluid and/or air passing though hoses. To

prevent such a risk, earth continuity to

the spray equipment and the object

being sprayed should be maintained.

Personal Protective

Equipment

Toxic vapours – When sprayed,

certain materials may be

poisonous, create irritation or be

otherwise harmful to health.

Always read all labels and safety data

sheets for the material before spraying

and follow any recommendations. If In

Doubt, Contact Your Material Supplier

The use of respiratory protective

equipment is recommended at all

times. The type of equipment must

be compatible with the material being

sprayed

Always wear eye protection when

spraying or cleaning the spraygun

Gloves must be worn when

spraying or cleaning the

equipment

Training – Personnel should be given

adequate training in the safe use of

spraying equipment.

Misuse

Never aim a spraygun at any part of the

body

Never exceed the max. recommended

safe working pressure for the equipment

The fitting of non-recommended or non-

original spares may create hazards

Before cleaning or maintenance, all

pressure must be isolated and relieved

from the equipment

The product should be cleaned using a

gun washing machine. However, this

equipment should not be left inside gun

washing machines for prolonged periods

of time.

Noise Levels

The A-weighted sound level of

sprayguns may exceed 85 dB

(A) depending on the set-up

being used. Details of actual

noise levels are available on

request. It is recommended that ear

protection is worn at all times when

spraying

4©ITW Ltd 2000

Parts List

Ref. No Description Part Number Qty

*1 Air Cap/Retaining ring GTI-407-* 1

1a Spring Clip JGA-156-K5 1

+2 Nozzle SEE CHART 1

3 Baffle & Seal GTI-425-K 1

Baffle Seal - Kit of 5 GTI-33-K5 1

+4 Packing GTI-439-K2 1

5 Spreader Valve GTI-405-K 1

6 Stud and Screw GTI-408-K5 1

+7 Needle SEE CHART 1

+8 Spring and Pad GTI-409-K5 1

9 Bushing GTI-402-K 1

10 Needle Adjusting Screw GTI-414-K 1

11 Valve Assembly JGK-449 1

12 Trigger GTI-108 1

13 Connector JGA-158 1

14 Airflow Valve GTI-415-K 1

15 Lock Nut JGA-51-K5 1

16 Seal 23165-001 1

17 Fluid Inlet Connector and seal JGA-159-K 1

18 Circlip 25746-007-K5 1

19 Circlip SST-8434-K5 2

20 Seal & Pin Kit ( + SST-8434-K5) GTI-428-K5 2

9a Seal kit of 5 JGS-72-K5 2

21 Air valve stem assembly JGS-431-1 1

22 Spring JGV-262-K5 1

* - * Denotes Aircap Number - Available Aircaps No’s 110, 122 and 123

+ - Parts included in service Kit (see accessories)

Nozzle Needle

GTI-213-085-K GTI-449-10-K

GTI-213-10-K GTI-449-10-K

GTI-213-11-K GTI-449-12-K

GTI-213-12-K GTI-449-12-K

GTI-213-13-K GTI-449-14-K

GTI-213-14-K GTI-449-14-K

GTI-213-15-K GTI-449-14-K

Nozzle Needle

GTI-214-16-K GTI-420-K

GTI-214-18-K GTI-420-K

GTI-214-20-K GTI-420-K

GTI-214-22-K GTI-420-K

Chart 1

5 ©ITW Ltd 2000

Specification

Air supply connection - Universa l 1/4BSP and NPS

Fluid Supply Connection - Universal 3/8BSP and NPS

Maximum static Air inlet pressure - P1= 9 bar (130 psi)

Maximum static Fluid inlet pressure - P2= 9 bar (130 psi)

Nominal gun Air inlet pressure - 2 bar (29 psi)

with gun triggered

Gun Weight - 500 g

Materials of Construction

Gun body - Anodised Aluminium

Nozzle - Stainless steel

Needle - Stainless Steel

6©ITW Ltd 2000

Installation

Important: To ensure that this

equipment reaches you in first class

condition, protective coatings have

been used. Flush the equipment

through with a suitable solvent

before use.

1. Attach air hose to connector (13).

Recommended hose size 8 mm

bore.

2. Attach fluid supply hose to Fluid

Inlet (17).

3. Air supply should be filtered and

regulated.

1. Turn off air and coating supply

and relieve pressure in the

supply lines, or if using QD

system, disconnect from airline

and fluid line.

2. Remove air cap (1) and clean. If

any of the holes in the cap are

blocked with coating material use

a toothpick to clean. Never use

metal wire which could damage

the cap and produce distorted

spray patterns

3. Ensure the tip of the nozzle (2) is

clean and free from damage.

Build up of dried paint can distort

the spray pattern.

Preventative Maintenance

Operation

1. Mix coating material to

manufacturers instructions

2. Turn needle adjusting screw (10)

clockwise to prevent movement.

3. Turn pattern valve (5) counter-

clockwise to fully open

4. Adjust inlet air pressure to give 2

bar (29psi) at the gun inlet with

the gun triggered. (pressure

gauge attachment shown under

Accessories is recommended for

this).

5. Turn needle adjusting screw

counter clockwise until first thread

shows.

6. Test spray. If the finish is too dry

reduce airflow by reducing inlet

pressure. If finish is too wet

reduce fluid flow by turning needle

screw (10) clockwise or reducing

the fluid pressure. If atomisation is

too coarse, increase inlet air

pressure. If too fine reduce inlet

pressure.

7. The pattern size can be reduced

by turning adjusting valve (5)

clockwise.

8. Hold gun perpendicular to surface

being sprayed. Arcing or tilting

may result in uneven coating.

9. The recommended spray distance

is 150-200 mm (6”-8”).

10.Spray edges first. Overlap each

stroke a minimum of 50%. Move

gun at a constant speed.

11.Always turn off air and fluid supply

and relieve pressure when gun is

not in use.

Air Flow Valve (14)

1. If the airflow valve (14) is fitted

this can be used to reduce the

inlet pressure through the gun.

Screw the Adjusting Knob in to

reduce pressure.

7 ©ITW Ltd 2000

4. Lubrication – stud/screw (6),

needle (7) and air valve (11)

should be oiled each day.

Nozzle (2) and Needle (7) –

Remove parts in the following order:

10, 8, 7, 1 and 2. Replace any worn

or damaged parts and re-assemble

in reverse order. Recommended

tightening torque for nozzle (2) 17-

20 Nm (150-180 lbf in)

Packing – Remove parts 10, 8, 7.

Unscrew cartridge (4). Fit new

cartridge finger tight. Re-assemble

parts 7, 8, and 10 and tighten

cartridge (4) with spanner sufficient

to seal but to allow free movement

of needle. Lubricate with gun oil.

Air valve (11) – Remove Trigger,

parts 6 and 12. Unscrew valve

assembly. Re-assemble, fitting

spring to valve head before fitting

valve.

Spreader valve (5) – Caution:

always ensure that the valve is in

the fully open position by turning

screw fully counter-clockwise before

fitting to body.

Air cap / Nozzle Selection

Refer to coating material

manufacturers recommendations or

ITW Finishing UK Website:

www.devilbiss-spraysite.co.uk

Replacement of Parts

Accessories

Spanner – order SPN-5

Cleaning Brush – order 4900-5-1-K3

Service Kit – For sizes 16 to 22 order GTI-416 and nozzle size as required

(i.e GTI-416-18)

For sizes 085 to 15 order GTI-426 and nozzle as required size as required

(i.e GTI-426-14)

Pressure gauge Attachment – order GA-515

Gun Mounted Regulator – order DVR-501

Lubricant - order GL-1-K10

8©ITW Ltd 2000

November 02

ITW Finishing Systems and Products

Ringwood Road,

Bournemouth,

BH11 9LH,

England.

Tel. No. (01202) 571111

Telefax No. (01202) 581940,

Website address http:\\www.itweuropeanfinishing.com

ITW Oberflächentechnik GmbH & Co. KG

Justus-von-Liebig-Straße 31

63128 Dietzenbach

Tel (060 74) 403-1

Telefax: (060 74) 403300

Website address http:\\www.itw-finishing.de

ITW Surfaces Et Finitions

163-171 avenue des Auréats B.P. 1453

26014 VALENCE CEDEX FRANCE

Tél. (33) 475-75-27-00

Télex 345 719F DVILBIS

Téléfax: (33) 475-75-27-99

Otros manuales para GTI

Tabla de contenidos

Otros manuales de Pistola pulverizadora de pintura de DeVilbiss

DeVilbiss

DeVilbiss Compact TRANS-TECH Manual de usuario

DeVilbiss

DeVilbiss JGP-503 CONVENTIONAL Manual de referencia

DeVilbiss

DeVilbiss NEPTUNE-L LVMP Manual de usuario

DeVilbiss

DeVilbiss NEPTUNE Series Manual de usuario

DeVilbiss

DeVilbiss AGXV-540 Manual de usuario

DeVilbiss

DeVilbiss MSV-531-28FF Manual de referencia

DeVilbiss

DeVilbiss MBC-ZINC-W Manual de usuario

DeVilbiss

DeVilbiss KK-5025 Manual de referencia

DeVilbiss

DeVilbiss SB-2-001-J Manual de usuario

DeVilbiss

DeVilbiss JGP-504 Manual de usuario

DeVilbiss

DeVilbiss FLG3 Manual de usuario

DeVilbiss

DeVilbiss Compact HVLP Manual de usuario

DeVilbiss

DeVilbiss FLG-691 Manual de referencia

DeVilbiss

DeVilbiss HVLP Gravity Feed Spraygun Manual de usuario

DeVilbiss

DeVilbiss LUNA MARK-II-K Manual de usuario

DeVilbiss

DeVilbiss GTi Millennium Manual de usuario

DeVilbiss

DeVilbiss KB-522 Manual de usuario

DeVilbiss

DeVilbiss SB-E2-2-252 Manual de usuario

DeVilbiss

DeVilbiss SRi Manual de usuario

DeVilbiss

DeVilbiss FLG-G5 Manual de usuario

DeVilbiss

DeVilbiss TGHV Series Manual de referencia

DeVilbiss

DeVilbiss AGB-541 Manual de usuario

DeVilbiss

DeVilbiss GFG HD Manual de servicio

DeVilbiss

DeVilbiss JGA-510 Manual de usuario

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Graco

Graco 246737 Manual de uso y cuidado

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

Graco

Graco EM 390 Manual de operación

Graco

Graco HydroShield WMBH00 Manual de lista de piezas