Connection and Adjustment
Lens Installation
Manual / Fixed Lens Connection
1. If using a C-mount lens, attach the C-mount before installaing the lens.
2. Movet the back focus adjustment fully to the left with the lens facing towards you
(see Back Focus Adjustment).
3. Install the lens on to the camera.
4. Adjust the Back Focus to the proper positon then secure the screw.
5. Adjust the Zoom and Focus levers of the lens to acquire the clear image.
Direct Drive (D.C.)Lens Connection
1. If using a C-mount lens, attach the C-mount before installaing the lens.
2. Movet the back focus adjustment fully to the left with the lens facing towards you
(see Back Focus Adjustment).
3. Install the lens on to the camera.
4. For Direct Drive Lens application, Connect the DC Lens Connector to the side of the
camera. Fit the lens to the camera according to the following connection assignments.
5. Adjust the Back Focus to the proper positon then secure the screw.
6. Adjust the Zoom and Focus levers of the lens to acquire the clear image.
Video Drive Lens Connection
1. If using a C-mount lens, attach the C-mount before installaing the lens.
2. Movet the back focus adjustment fully to the left with the lens facing
towards you (see Back Focus Adjustment).
3. Install the lens on to the camera.
4. For Video Drive Lens application, connect the wires to the rear panel of the
camera. Fit the lens to the camera according to the following
connection assignments.
5. Adjust the Back Focus to the proper positon then secure the screw.
6. Adjust the Zoom and Focus levers of the lens to acquire the clear image.
Protective
Cover
Back Focus
Adjustment
Lens
(Optional)
CS Mount
(for C-type Lens)
Zoom and Focus
Adjustment
Back Focus
Adjustment
Lens (Optional)
Zoom and Focus
Adjustment
DC Lens
Pin Assignments
Back Focus
Adjustment
Lens (Optional)
Zoom and Focus
Adjustment
Lens
Connector
Pin Number DC Drive
Pin 1 Damp-
Pin 2 Damp +
Pin 3 Drive +
Pin 4 Drive -
2
1
4
3
Back Focus
Adjustment
Lens (Optional)
Zoom and Focus
Adjustment
Installing the Lens
Before installing a lens, you must first
remove the protective cover from the
camera. If mounting a C-Mount lens,
attach the CS mount to the camera.
Adjust the Back Focus to acquire a
sharp image
(see Back Focus Adjustment).
Back Focus Adjustment
There is a mechanism for back focus adjustment.
Unscrew (loosen) the back focus screw.
Move the adjustment to the proper position
so as to make the better camera image.
Tighten the screw to lock the back focus
adjustment in place. Back Focus Adjustment
Video Lens
Connector
Camera Setup
Camera Configuration
There is a bank of DIP switches in the rear of the camera.
The DIP Switches allow the settings as follows:
LL / INT
In LL Mode, the V-Phase may be adjusted to compensate for connected supply phase differences.
Only applicable for AC supply – otherwise the camera should be operates
with INT (internal) sync.
SDN / ON
This feature enables the camera operates in monochrome mode in reduced lighting. Switch to ON to
activate.
BLC / ON
The Backlight Compensation feature eliminates the effect of strong background lighting, maintaining the
correct exposure.
Switch to ON to activate. When switched to BLC, the feature is off.
AGC / TURBO
The Automatic Gain Control feature can improve picture quality in low lighting conditions. Select TURBO for
most applications.
Setting to AGC will remove 'noise' from the image, but it will also limit the camera's sensitivity
AES/ ON
Selecting ON enables Electronic Iris mode, which compensates for excessive light levels by automatically
adjusting the camera shutter speed. This mode should only be used with fixed or manual iris lenses.
F.L. / ON
When this switch is set to ON, the camera reduces flicker in the
image under fluorescent lighting.
