Detecto IB Series Manual de usuario

0046-M570-O1 Rev A •IBFL500 ASSEMBLY INSTRUCTIONS 1

IB Series

Model IBFL500

Assembly Instructions

Technical Support: Ph: 866-254-8261

•

[email protected]Technical Support: Ph: 866-254-8261

•

[email protected]

0046-M570-O1 Rev A •IBFL500 ASSEMBLY INSTRUCTIONS2

0046-M570-O1 Rev A •IBFL500 ASSEMBLY INSTRUCTIONS 1

INTRODUCTION

Thank you for purchasing our DETECTO™ IB Series Model IBFL500 in-bed scale. It has been

manufactured with quality and reliability at our factory in Webb City, MO USA. This scale has

been assembled and tested before leaving our factory to insure accuracy and dependability for

years to come.

This manual is provided to guide you through the assembly of your scale. Please read it

thoroughly before attempting to assemble your scale and keep it handy for future reference.

pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to

the use of the information contained herein.

DISCLAIMER

While every precaution has been taken in the preparation of this manual, the Seller assumes

no responsibility for errors or omissions. Neither is any liability assumed for damages resulting

from use of the information contained herein. All instructions and diagrams have been

checked for accuracy and ease of application; however, success and safety in working with

tools depend to a great extent upon the individual accuracy, skill and caution. For this reason

the Seller is not able to guarantee the result of any procedure contained herein. Nor can they

assume responsibility for any damage to property or injury to persons occasioned from the

procedures. Persons engaging the procedures do so entirely at their own risk.

DANGER! NOT A PATIENT TRANSPORT DEVICE!

This scale is NOT intended for use in transporting patients! It is to be

used ONLY for weighing a patient. Failure to observe this warning may

result in serious injury to the patient and/or the scale operator.

PRECAUTIONS

Before beginning assembly of this scale, read this manual and

pay special attention to all "NOTIFICATION" symbols:

IMPORTANT:

0046-M570-O1 Rev A •IBFL500 ASSEMBLY INSTRUCTIONS2

ASSEMBLY INSTRUCTIONS

The IB Series Model IBFL500 in-bed scale is shipped disassembled in two (2) separate

cartons. Carefully inspect all cartons for damage that may have taken place during shipment.

It is the responsibility of the purchaser to file all claims with the shipping company for damages

or loss incurred during transit.

Packing Checklist

NOTE: All nuts, bolts or screws are already in position on the scale and “finger tight”. No

hardware is package separately. Contents of cartons should include:

Item Description Part Number Qty

Carton 1

Base Assembly 0046-D533-1A 1

Column Weldment 0046-D547-0A 1

Carton 1 – Inner Upper Section

Boom Assembly 0046-C279-0A 1

Hydraulic Cylinder 6540-1119 1

Indicator / Handle Assembly 0046-B549-1A 1

Stretcher Cup 0046-B005-08 1

Anti-Swing Bar 0046-B518-08 2

¾0.5 ml Capsule, Loctite® 6560-1046 1

Indicator Model 750 1

Carton 1 – Inner Lower Section

Stretcher Hoop 0046-D261-08 2

Carton 2

Stretcher Support Bars 0046-C248-08 2

Stretcher 0046-C247-08 1

¾The capsule of Loctite® is in a plastic bag taped to the Boom Assembly.

Tools Required

The following tools are required to assemble the IB Series Model IBFL500 in-bed scale:

1/2" drive ratchet wrench

1/2” drive 15/16” and 3/4” standard socket

15/16”, 1/2" and 7/16" wrench (open end, box end, or combination)

5/16” and 3/16” Allen wrench

Small Flat Blade Screwdriver

0046-M570-O1 Rev A •IBFL500 ASSEMBLY INSTRUCTIONS 3

Unpacking

IMPORTANT: UNPACKING AND ASSEMBLY OF THIS PRODUCT REQUIRES

TWO PEOPLE. PLEASE READ THROUGH THE INSTRUCTIONS CAREFULLY

BEFORE STARTING TO ASSEMBLE THE SCALE.

Remove the shipping straps and packing material to unpack the IB Series Model IBFL500

in-bed scale. Check the parts against the PACKING CHECKLIST. If any are damaged or

missing, please contact our Parts Department at 1-800-641-2045 or by email at

[email protected].

NOTE: Leave the shipping straps and packing material on the Boom Assembly

until instructed to remove it in Step 7.

Carton 1 – Inner Upper Section

Carton 1

Carton 2

Carton 1 – Inner Lower Section

0046-M570-O1 Rev A •IBFL500 ASSEMBLY INSTRUCTIONS4

Step 1 – Prepare the Base Assembly

1. With the help of an assistant, remove the

Column Assembly from Carton 1.

Remove Column Assembly

2. Next, remove the plastic bag and packing

from the Base Assembly in Carton 1.

Remove Plastic Bag and Packing

3. Again, with the help of an assistant, remove

the Base Assembly from the Carton 1.

Remove Base Assembly

4. Set the brakes on the rear wheels.

Set Brakes on Rear Wheels

Push

Down

Brake

0046-M570-O1 Rev A •IBFL500 ASSEMBLY INSTRUCTIONS 5

Step 2 – Install Column Assembly

1. Remove¾the 5/8-11 elastic stop nut and 5/8-11 x 3 1/2” hex head bolt in the top of the

base assembly.

2. Next, then turn the base over (upside down) and remove¾the 5/8-11 elastic stop nut and

5/8-11 x 3 1/2” hex head bolt in the bottom of the base assembly.

¾Use the 1/2” drive ratchet with the 15/16 socket and 15/16” wrench if needed.

Remove Top Bolt from Base, then turn over to remove Bottom Bolt from Base

3. Place the Column Assembly into the rectangular opening of the base assembly until it

stops. NOTE: The opening in the base assembly is angled back away from the leg

assemblies of the base. The column assembly must be inserted at an angle and then

slid into the opening.

4. Install¾¾ the 5/8-11 x 3 1/2” hex head bolt and 5/8-11 elastic stop removed in step 1 in

the top hole of the base assembly.

5. Next, turn the base on its side and install¾¾ the 5/8-11 x 3 1/2” hex head bolt and 5/8-11

elastic stop removed in step 2 in the bottom hole of the base assembly.

¾¾Use the 1/2” drive ratchet with the 15/16 socket and 15/16” wrench to tighten.

Rectangular opening in Base

Install Top Bolt and Nut

Insert Column at an angle

Turn base on its side and

install Bottom Bolt and Nut

0046-M570-O1 Rev A •IBFL500 ASSEMBLY INSTRUCTIONS6

Step 3 – Install Stretcher Cup

1. Remove the 1/4-20 x 1/2” hex head bolt from the Stretcher Cup mounting bracket. Use

the 7/16 wrench if needed.

2. Place the Stretcher Cup on the mounting bracket, align the center hole in the cup with

the hole in the mounting bracket and secure with the 1/4-20 x 1/2” hex head bolt. Use

the 7/16 wrench to tighten.

Remove mounting bolt Use center mounting hole Stretcher Cup Installed

Step 4 – Install Boom Assembly

1. Remove the 1/2-13 elastic stop nut and 5/8” split lock washer from the 5/8 x 2 1/2”

shoulder bolt in the column assembly and then slide the bolt out of the column assembly.

Use the 1/2” drive ratchet with the 3/4” socket and 5/16” Allen wrench if needed.

2. With the help of an assistant, place the Boom Assembly between the mounting plates of

the column assembly and align the hole in the boom assembly with the holes in the

column assembly mounting plates.

3. Insert the 5/8 x 2 1/2” shoulder bolt removed in step 1 through the hole in the mounting

plate of the column assembly. Next, install the 5/8” split lock washer and 1/2-13

elastic stop nuts removed in step 1 and tighten. Use the 1/2” drive ratchet with the

3/4” socket and 5/16” Allen wrench to tighten.

Remove Bolt from Column Have an assistant hold the Boom

Assembly while inserting the bolt

0046-M570-O1 Rev A •IBFL500 ASSEMBLY INSTRUCTIONS 7

Step 5 – Install Hydraulic Cylinder

1. Lower the boom assembly and remove the 5/16-18 elastic stop nut and 3/8” split lock

washer from the 5/16-18 x 1/2” socket head shoulder bolt in the boom assembly, then

slide the bolt out of the boom assembly. IMPORTANT: Note the location of the bolt in

the cylinder mounting plate; it must be re-installed in the same location. Use the 1/2”

wrench and 3/16” Allen wrench if needed.

2. While the assistant is holding the boom assembly up, place the shaft end of the hydraulic

cylinder (end with the hole) between the cylinder mounting plates in the boom assembly

and then align the hole in the shaft with the holes in the mounting plates.

3. Insert the 5/16-18 x 1/2” socket head shoulder bolt into the hole (where it was removed

in step 1) in the mounting plate, through the cylinder shaft and out the mounting plate.

Next, install the 3/8” split lock washer and 5/16-18 elastic stop nut removed in step 1

and tighten. Use the 1/2” wrench and 3/16” Allen wrench to tighten.

4. Next, align the ball end of the hydraulic cylinder with the ball socket on the column

assembly and insert the ball into the socket. Tighten the cylinder nut to hold in place.

Hand-tighten only.

Note

original

location of Bolt

Remove Bolt, Washer & Nut

Bolt installed in

correct location

Align ball end with ball socket

and

tighten

only

0046-M570-O1 Rev A •IBFL500 ASSEMBLY INSTRUCTIONS8

Step 6 – Install Push Handle

1. Remove the (4) 1/4-20 x 1/2” hex head bolts

(two on each side) from the column assembly.

Use the 7/16” wrench if needed.

Remove Push Handle Bolts

2. Place the Push Handle on the column

assembly (the opposite direction of the legs)

and align the top hole in the handle mounting

bracket with the top hole in the column

assembly. Insert a 1/4-20 x 1/2” hex head bolt

through the hole and finger tighten.

3. Align the bottom hole in the handle bracket

with the bottom hole in the column assembly

and insert a 1/4-20 x 1/2” hex head bolt

through the hole and finger tighten.

4. Repeat steps 2 and 3 for the push handle bolts

on the other side of the column assembly.

5. Completely tighten all bolts to secure the push

handle to the column assembly. Use the 7/16”

wrench to tighten.

Tighten all Push Handle Bolts

Install top Bolt and finger tighten.

Next, install bottom Bolt and finger

tighten. Repeat for other side.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo médico de Detecto

Detecto

Detecto Solace ID-3636S-855RMP Manual de usuario

Detecto

Detecto Detecto 8432-CH Manual de usuario

Detecto

Detecto HealthySole Plus Manual de usuario

Detecto

Detecto 6800 Manual de usuario

Detecto

Detecto DLM Manual de usuario

Detecto

Detecto IB800 Manual de usuario

Manuales populares de Equipo médico de otras marcas

TekTone

TekTone Tek-CARE160 Manual de usuario

NeuroMetrix

NeuroMetrix Quell 2.0 Manual de usuario

AMT

AMT XLR8 Manual de usuario

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Manual de usuario

EDAN

EDAN SONOTRAX Pro Manual de usuario

Restorative Therapies

Restorative Therapies RT300 Manual de usuario

Gendex

Gendex Expert DC Manual de usuario

Dexcowin

Dexcowin ADX4000W Manual de usuario

Libelium

Libelium MySignals Manual de usuario

Acelity

Acelity V.A.C.ULTA 4 Manual de usuario

Caputron

Caputron ActivaDose II tDCS Manual de usuario

FujiFilm

FujiFilm Sonart Manual del propietario

Plinth 2000

Plinth 2000 93CDT Manual de usuario

GE SENOGRAPHE 800T Manual de usuario

GE Definium 5000 Manual de usuario

Kanmed

Kanmed GE-1380 Manual de usuario

Huntleigh

Huntleigh FD1 Manual de usuario

Stryker

Stryker SPR Plus Manual de usuario