DESi KC2 Manual de usuario
Wireless
Touch Keypad
USER MANUAL
KC2
1. PARTS and INSTALLATION
2
Display
Mounting
Holes
Touch
Buttons
Settings
Button
Lock
Button Screw for Changing Batteries
You can install the device by using two
screw holes shown on the below. If the
device will be used in a secure place like
an office in a secured building, it can be
placed easily by using 2-way stickers
provided with the product.
3
2. GENERAL INFORMATION and WARNINGS
-If there is any problem with door or locking mechanism, first of
all, those problems need to be solved. Otherwise, there would be
problems during operating the device.
-If there is a problem with the device, contact with your dealer.
-Replace the batteries, if there is a battery warning.
-It needs to be protected from water and direct sunlight.
-Do not touch to electronic parts of the device with a
conducting metal or sharp object.
-Do not use water or corrosive chemicals to clean the device.
2.1. KEYPAD MENU NAMES
1- Door handling direction
2- Number of turns adjusting
3- Buzzer
4- Auto lock (Utopic-R) /
Semi auto lock (Utopic-2)
5- Delayed lock (Utopic-R) /
Night mode (Utopic-2)
6- Pairing new device
7- Password create/change
8- Latch period
9- Device type
0- OTP
Lock Buton- Language
4
3. ADMINISTRATION ACTIONS / SETTINGS FOR KEYPAD
Two different 5 digit passwords may be defined to the keypad;
1 master, 1 user. Both of the passwords can be use to unlock and
open. For settings, the master password need to be entered.
Default master password is “12345". User password is not set.
WARNING: First of all, change the default master password.
3.1. Changing Default Master Password
-Tap with your palm to wake up the device. Then touch the
“SETTINGS” button. "MASTER" will be displayed on the screen.
-Enter “12345” as the default password. “≡≡” symbol will appear
on the screen.
-Touch the "7" button. "PASSWORD" will appear on the screen.
Touch the "SETTINGS" button to enter menu.
-When the "MASTER" appears, touch the "SETTINGS" button again.
-Enter your new 5-digit master password when “NEW PASS” is
displayed on the screen. When “REPEAT” is displayed, re-enter the
5 digit password. Thus, your master password will be changed.
5
3.2. Set / Change User Password
-Tap with your palm to wake up the device. Then touch the
“SETTINGS” button. "MASTER" will be displayed on the screen.
-Enter 5 digit master password. “≡≡” symbol will appear on
the screen.
-Touch the "7" button. "PASSWORD" will appear on the screen.
Touch the "SETTINGS" to enter menu.
-When the "MASTER" appears, touch the "LOCK" button .
-When the "USER" appears on the screen, touch the
"SETTINGS" button.
- Enter your new 5-digit user password when “NEW PASS” is
displayed on the screen. When “REPEAT” is displayed, re-enter
the 5 digit password. Thus, your user password will be set/
changed.
You can change the user password by following the same steps.
6
4. SMART LOCK SETTINGS
IMPORTANT NOTE: You can change the settings through keypad if
it is paired as master controller to smart lock.
4.1. Pairing Wireless Controllers to the Smart Lock
-Tap with your palm to wake up the device. Then touch the
“SETTINGS” button. "MASTER" will be displayed on the screen.
-Enter 5 digit master password. “≡≡” symbol will appear on the
screen.
-Touch the "6" button. "U.ENROLL" will appear on the screen.
Touch the "SETTINGS" to start pairing.
-A long tone will be heard first, then a short tone. Send an RF
signal from the device you want to pair with after the short tone.
(Please refer to the next page to send RF signal from controllers)
The new controller will be paired to the smart lock when 2 sequential
warning tones are heard.
7
How to Send a RF Signal from Controllers
Remote Controllers: Press 1st button.
Open Button: Press the button.
Fingerprint Reader: Wake up and touch to locking button.
Keypad: Wake up and touch to lock button.
Auto-Closer: Bring the magnet closer to the device and than
seperate it from device.
Home-Automation Interface: Short-circuit red and white cables
and than open-circuit.
4.1.1 Changing the Keypad Language
- Tap with your palm to wake up the device. Then touch the
“SETTINGS” button. "MASTER" will be displayed on the screen.
- Enter 5 digit master password. “≡≡” symbol will appear on
the screen.
- Touch the "LOCK" button. "LANGUAGE" will appear on the
screen. Touch the "SETTINGS" to enter menu.
- Touch the "LOCK" to change language and touch "SETTINGS"
to confirm.
8
4.2. Adjusting Direction of Locking
-Tap with your palm to wake up the device. Then touch the
“SETTINGS” button. "MASTER" will be displayed on the screen.
-Enter 5 digit master password. “≡≡” symbol will appear on the
screen.
-Touch the "1" button. "D.HANDING" will appear on the screen.
Touch the "SETTINGS" to enter menu.
-"RIGHT" will appear on the screen. Touch the 'LOCK' to change to
“LEFT”. Touch the “SETTINGS” to save your choice.
IMPORTANT NOTE: After the first lock or unlock command sent from
keypad, the selected settings will be transferred to the smart lock.
9
4.3. Adjusting The Number of Turns
-First of all, close your door. Make sure that the door is not locked.
-Tap with your palm to wake up the device. Then touch the
“SETTINGS” button. "MASTER" will be displayed on the screen.
-Enter 5 digit master password. “≡≡” symbol will appear on the
screen.
-Touch the "2" button. "TURN COUNT" will appear on the screen.
Touch the "SETTINGS" to adjust automatically.
-The smart lock will give a long (3 sec) warning tone and it will lock
and unlock the door.
When the sequential warning tone sounds, your smart lock learn
how many turns it needs to be fully lock / unlock.
10
4.4. Adjusting Buzzer Sound of Smart Lock
-Tap with your palm to wake up the device. Then touch the
“SETTINGS” button. "MASTER" will be displayed on the screen.
-Enter 5 digit master password. “≡≡” symbol will appear on the
screen.
-Touch the "3" button. "BUZZER" will appear on the screen. Touch
the "SETTINGS" to adjust automatically.
-Touch the 'LOCK' to cycle through the selections; "ON" means
audible warning is on, "OFF" means audible warning is off.
-Touch the “SETTINGS” to save your choice.
IMPORTANT NOTE: After the first lock or unlock command sent from
keypad, the selected settings will be transferred to the smart lock.
Tabla de contenidos
Otros manuales de Teclado de DESi
