Denver CR-416 Manual de usuario
CR-416
INSTRUCTION MANUAL
BRUKSANVISNING
BETJENINGSVEJLEDNING
BEDIENUNGSANLEITUNG
MANUAL DE INSTRUÇÕES
INSTRUCCIONES DE USO
KÄYTTÖOHJEET
GEBRUIKERSHANDLEIDING
INSTRUKCJA OBSLUGI
www.denver-electronics.com
www.facebook.com/denverelectronics
English
FUNCTION AND CONTROLS
1. MEMORY.SET / MEMORY+ / DISPLAY LIGHT AUTO ON/OFF /
NAP
2. ALARM 1 ON / OFF SET
3. ALARM 2 ON / OFF SET
4. SNOOZE / SLEEP / DIMMER
5. CLK.ADJ. (TIME SET) / TEMP
6. << / TUNE -/ YEAR/MONTH/DAY
7. >> / TUNE + / DST/C-F
8. VOLUME UP / DISPLAY AUTO CHANGE ON/OFF
9. ON/OFF
10. VOLUME DOWN
11. DISPLAY
12. BATTERY COMPARTMENT (REAR OF UNIT)
13. RESET
14. RATING LABEL (REAR OF UNIT)
15. SPEAKER
16. TEMPERATURE SENSOR (IN DOOR)
17. FM ANTENNA
18. AC POWER CORD
POWER CONNECTION
Plug the AC power cord to a household outlet AC source. This unit
is equipped with a battery back up system, it requires a 3V CR2032
at lithium battery (not included). Insert the battery in the battery
compartment, making certain that the positive and negative (+ and -)
battery terminals are attached to the corresponding terminals on the
plate in the battery compartment. If an AC power failure occurs, the
clock automatically switches to the battery power supply, the clock and
timer memory continue running. When the AC power resumes, the clock
switches back to AC again.
GETTING STARTED
Press the RESET button (13) locates on the back of unit after AC plug
in.
- The unit will display full segment for 2 seconds, then it will enter the
normal mode.
1. TIME AND CALENDAR MANUAL SETTING
A. Setting Time and Calendar – Press Time set button (5) in normal
mode and keep depress over 2 seconds to enter time set mode,
after enter the setting mode, press Time set button (5) to change the
mode cycle as follows :
Normal → Year → Month → Day → 12/24 H → Real time Hour → Real
time Min → Normal
Action (during data adjustment):
- Press << / Tune -button (6) to adjust data backward.
- Press >> / Tune + button (7) to adjust data forward.
- Keep depress << or >> button for 2 seconds to enable auto forward.
LED DISPLAY
TIME Indicator
MHz Indicator
ALARM 2 Indicator
PM Indicator
SANDBYIndicator
ALARM 1Indicator
B. Setting Alarm 1 and Alarm 2 – Press alarm set button (2/3) during
normal mode and keep depress over 2 seconds to enter alarm set
mode, after enter the setting mode, press alarm set button (2/3) to
change the mode cycle as follows :
Normal → AL 1 Hour → AL1 Min → AL 1 weekday Alarm → AL 1 wake
beep → AL 1 wake radio → AL 1 wake radio volume → Normal
Normal → AL 2 Hour → AL2 Min → AL 2 weekday Alarm → AL 2 wake
beep → AL 2 wake radio → AL 2 wake radio volume → Normal
Select alarm weekday mode as follows
1-5 : Monday to Friday
1-7 : Whole week
6-7 : Saturday & Sunday
1-1 : One day of week
Action (during data adjustment) :
- Press << / Tune -button (6) to adjust data backward.
- Press >> / Tune + button (7) to adjust data forward.
- Keep depress << or >> button for 2 seconds to enable auto forward.
2. SETTING ALARM OUTPUT ON/OFF
Press MEMORY.SET / MEMORY+ / DISPLAY LIGHT AUTO ON/OFF
/ NAP button (1) to the Auto off mode, alarm wake up the display is
auto turn on.
Press alarm 1 on/off set button (2) to toggle on and off alarm output
function.
Press alarm 2 on/off set button (3) to toggle on and off alarm output
function.
3. ALARM DURATION AND SNOOZE FUNCTION
Alarm Duration – Beep alarm or radio alarm will continue output for
30 minutes if no key press, then it will stop automatically and wait for
same alarm time on next day.
Action for Snooze :
- During alarming, press Snooze button (4) will enable snooze
function, Beep alarm or Radio alarm will stop.
- Snooze interval is 9 minute (not include second offset)
- Snooze will continue unless press ON/OFF button (12) to alarm off
of Buzzer alarm or Radio Alarm stop automatically after 30 minutes.
Press MEMORY.SET / MEMORY+ / DISPLAY LIGHT AUTO ON/OFF
/ NAP button (1) to the Auto off mode, during alarming display auto
turn on, press snooze / sleep button (4) will enable snooze function,
buzzer alarm or radio / display will stop & off.
4. CHANGE DISPLAY CONTENT Press << / Tune -/ YEAR/MONTH/
DAY button (6) during normal can switch to display Year / Month /
Day, after 5 seconds timeout and return back to display time.
Listening to Radio
Press the ON/OFF button (9) to turn the unit on. Use the Tune + or
Tune – button to select the desired FM station. If you press and hold
the Tune + or Tune – button for one second, the release, the unit will
automatically scan to the next broadcasting station. Press the ON/OFF
button (9) to turn the radio OFF.
To set / recall the radio presets
Press the ON/OFF button (9) to turn the unit ON.
Use the Tune + or Tune -button to select the desired FM station.
Press the memory / memory + button; “P01” will blink in the display.
Press the memory / memory + button again to set the preset.
Repeat steps 2 through 4 to set more presets.
The unit can preset 10 stations totally for FM.
When “P01-P10” is blinking, press the Tune+ or Tune-button to select
YEAR Indicator
MONTH Indicator DAY Indicator
the preset number.
When recalling preset stations, press memory / memory + to select the
preset number.
Sleep operation
When listening to radio, press Snooze / Sleep button (4) to enter sleep
mode. You can just adjust the sleep timer from 90 mins to 15 mins by
pressing the Snooze / Sleep button (4). The unit will automatically turn
off after the selected time.
NAP timer function (count down timer)
During radio off mode, press MEMORY.SET / MEMORY+ / DISPLAY
LIGHT AUTO ON/OFF / NAP button (1) to turn on NAP mode, the NAP
time will keep by 5 seconds, within 5 seconds and press MEMORY.
SET / MEMORY+ / DISPLAY LIGHT AUTO ON/OFF / NAP button (1)
button can change the duration from 90 min – 10 min. The alarm buzzer
will sound for 30 min and then shut off automatically. To stop the alarm
buzzer, press the ON/OFF button (9).
Press the MEMORY.SET / MEMORY+ / DISPLAY LIGHT AUTO ON/
OFF / NAP button (1) has no effect during alram operation. Press ON/
OFF button (9) to cancel NAP function.
SPECIFICATIONS
Frequency range : FM 87.5 – 108 MHz
Battery backup : 3V (CR2032 Flat Lithium battery x 1) not included
Power supply : AC230V 50Hz
RESET
The reset button is located on the back of unit. Use a ballpoint pen to
press it whenever you change the batteries, or unit is not performing as
expected. This will return all settings to default value, and you will lose
any stored data (alarm and clock settings).
Note :
- Ensure that the FM antenna is completely unrolled and extended for
best FM reception.
WARNING
1 No naked ame sources, such as lighted candles, should be placed
on the apparatus.
2 Do not place the product in closed bookcases or racks without
proper ventilation.
3 Where the mains plug is used as the disconnect device, the
disconnect device shall remain readily operable.
4 The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, table-cloths, curtains,
etc.
5 It shall not be exposed to dripping or splashing and that no objects
lled with liquids, such as vases, shall be placed on the apparatus.
6 Do not connect FM antenna to outside antenna.
7 The unit should not be exposed to direct sunlight, very high or low
temperature, moisture, vibrations or placed in dusty environment.
8 Do not use abrasive, benzene, thinner or other solvents to clean the
surface of the unit. To clean, wipe it will mild non-abrasive detergent
solution and clean soft cloth.
9 Never attempt to insert wires, pins or other such objects into the
vents or opening of the unit.
10. Disconnect device warning : Mains plug is used as the connection,
so it should always remain ready operate.
11.Batteries shall not be exposed to excessive heat such as sunshine,
re or the like.
12.Class 1LED product.
CAUTION
Danger of explosion if battery is incorrectly replaced Replace only with
the same or equivalent type
Electric and electronic equipment contains materials, components and
substances that can be hazardous to your health and the environment,
if the waste material (discarded electric and electronic equipment) is
not handled correctly.
Electric and electronic equipment is marked with the crossed out trash
can symbol, seen below. This symbol signies that electric and
electronic equipment should not be disposed of with other household
waste, but should be disposed of separately.
All cities have established collection points, where electric and
electronic equipment can either be submitted free of charge at recycling
stations and other collection sites, or be collected from the households.
Additional information is available at the technical department of your
city.
ALL RIGHTS RESERVED
DENVER ELECTRONICS A/S
www.denver-electronics.com
www.facebook.com/denverelectronics
Swedish
FUNKTIONER OCH KONTROLLER
1. Minne/Minne Upp/Display ljus auto på/av/NAP
2. Alarm 1 På / Av / inställt
3. Alarm 2 På / Av / Inställt
4. Snooze / Sleep / DIMMER
5. Tid inst/temp Radio frekvens
6. « / Inställning - / ÅR / DAG
7. » / Inställning + /C-F/ DST
8. Volym Up / Display auto ändring på/av
9. PÅ/AV
10. Minska Volym
11. Display
12. Batterfack (bak på enheten)
13. ÅTERSTÄLL
14. Klassiceringsetikett (bak på enheten)
15. HÖGTALARE
16. TEMPERATURGIVARE (INOMHUS)
17. FM Antenn
18. AC STRÖMSLADD
STRÖMANSLUTNING
Anslut strömsladden till ett vägguttag för växelström. Denna apparat
är försedd med ett uppbackningssystem, det kräver ett 3V CR2032
platt litiumbatteri (ingår inte). Lägg i batteriet i batterifacket, se till
att batteriets positiva och negativa (+ och -) batteripolerna ansluts
till motsvarande poler på plattan i batterfacket. Uppstår ett fel på
växelströmförsörjningen, kopplar klockan automatiskt till batterkraft,
klockan och tidminnet fortsätter att gå. När växelströmmen återkommer,
kopplar klockaan automatiskt tillbaka till huvudströmmen.
KOMMA IGÅNG
Efter att kontakten anslutits tryck återställningsknappen (13) placerad
på enhetens baksida.
- Enheten visar helt segment i 2 sekunder, därefter normalt läge.
1. MANUELL INSTÄLLNING AV TID OCH DATUM
A. Ställa in tid och datum - Tryck tidknappen (5) i normalt läge och
håll nedtryckt i 2 sekunder för att öppna inställningsläge tid, efter att
inställningsläget öppnats tryck tidknappen (5) för att ändra
lägescykeln som följer :
Normal → År → Månad → Dag → 12/24 tim → RTC tim → RTC Min →
Normal
Aktivitet (vid datajustering)
- Tryck << / Inställning- knappen (6) för att justera data bakåt
- Tryck << / Inställning + (7) för att justera data framåt
- Håll nedtryckt « eller» knappen i 2 sekunder för att aktivera auto
fram.
B. Ställa in Alarm 1 och Alarm 2 - Tryck alarmknappen (2/3) i normalt
läge och håll nedtryckt i 2 sekunder för att öppna inställningsläge
alarm, efter att inställningsläget öppnats tryck alarmknappen (2/3) för
LED DISPLAY
Tidsindikering
MHz Indikering
ALARM 2 indikering
PM indikering
STANDBY Indikering
ALARM 1 indikering
Tabla de contenidos
Idiomas:
Otros manuales de Radio reloj de Denver
Denver
Denver CRP-618 Manual de usuario
Denver
Denver CRP-717 Manual de usuario
Denver
Denver CRL-330 Manual de usuario
Denver
Denver CRL-290 Manual de usuario
Denver
Denver CRP-617 Manual de usuario
Denver
Denver CRP-512 Guía de inicio rápido
Denver
Denver DAB-36 Manual de usuario
Denver
Denver CR-26 DABPLUS Manual de usuario
Denver
Denver CR-419 MK2 Manual de usuario
Denver
Denver CR-215 Manual de usuario
Denver
Denver CR-421 Manual de usuario
Denver
Denver CRB-618 Manual de usuario
Denver
Denver CRL-330 Manual de usuario
Denver
Denver IFM-90 Manual de usuario
Denver
Denver CRL-330 Manual de usuario
Denver
Denver CR-213 Manual de usuario
Denver
Denver CRI-812 Manual de usuario
Denver
Denver CR-323 Manual de usuario
Denver
Denver CRP-112 Manual de usuario
Denver
Denver CRQ-110 Manual de usuario
