Denon AVR-2312CI Manual de usuario

- 1 -

DENON AVR control protocol

Ver.7.5.0

Application model :AVR-2312CI/AVR-2312

Application terminal: RS-232C

Ethernet



Connector specification

Ⅰ. RS-232C

Connector type: DB-9pin female type, slave straight connection (DCE type)

( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )

Communication format:

Synchronous system : Tone step synchronization

Communication system : A half duplex

Communication speed : 9600bps

Character length : 8 bits

Parity control : None

Start bit : 1 bit

Stop bit : 1 bit

Communication procedure : Non procedural

Communication data length : 135 bytes (maximum)



Version Date Contents Page

7.5.0 15.Apr.’11 Original

- 2 -

Ⅱ. Ethernet

Connector type ：RJ-45(10BASE-T/100BASE-TX)

Communication format ：

Communication system : A half duplex

Communication speed : 10Mbps/100Mbps

Communication port : TCP port 23 (telnet)

Communication data length : 135bytes (maximum)

AVR

Ethernet

Cross cable

AVR

HUB

Ethernet

Straight

cable

Ethernet

Straight

cable

Example ①

Example ②

- 3 -

NETWORK SETUP of AVR-2312

>Procedure of Network Setup mode.

(1)Press MENU button, then Menu appears on FL-display(and GUI)

(2)Select “Manual Setup > Network Setup > Network Connecting > Detail” .

(3)Set parameters described below.

<DHCP> "ON"---Use this setting when DHCP server is on the local network.

"OFF"---Use this setting when DHCP server is not on the local network.

<IP Address> When <DHCP> sets "OFF”, please set IP address.

When <DHCP> sets "ON”, you can confirm the IP address that is set by server.

<Subnet Mask> When <DHCP> sets "OFF”, please set Subnet Mask.

When <DHCP> sets "ON”, you can confirm the Subnet Mask that is set by server.

<Gateway> Set the address of Gateway when Gateway is on the local network.

Do not set this parameter when Gateway is not on the local network.

<Primary DNS> Do not set this parameter.

<Second DNS> Do not set this parameter.

<Proxy> Set this parameter "OFF".

(1)Press MENU button, then Menu appears on FL-display (and GUI)

(2)Select “Manual Setup > Network Setup>Other > Network Standby”

(3)Set parameters described below.

“ON”---Use this setting when using the AVR-2312 Connected in a network.

“OFF”--- Use this setting when not using the AVR-2312 connected in a network.

This setting is reducing the power consumption in the standby mode.

- 4 -

Protocol specification

The following three data forms are defined.

COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.)

A command to a system is given from a controller.

EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR)

The result is sent, when a system is operated directly and a state changes.

*The form of EVENT presupposes that it is the same as that of COMMAND.

**Refer to the following table for the contents of COMMAND and EVENT.

RESPONSE : The message sent to a controller (Touch Panel etc.) from a system (AVR)

if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.

The RESPONSE should be sent within 200ms of receiving the COMMAND.

*The form of RESPONSE presupposes that it is the same as that of EVENT.

Basic specification: The command by ASCII CODE, parameter expression

*ASCII CODE which can be used is from 0x20 to 0x7F: the alphabet and the number of 0-9, and space (0x20), some signs,

AND carriage return (0x0D) --- It is used only as a pause sign.

Command structure: COMMAND + PARAMETER + CR (0x0D)

COMMAND: ASCII CODE of 2 characters

Ex. SI : Select Input source

MS : surround Mode Setting

MV : Master Volume setting

PW : system PoWer setting

PARAMETER : ASCII CODE ( up to 25 characters)

ex. DVD : function name

SUPER STADIUM : surround mode name

*Special Parameter--- ? : for request command

- 5 -

The example of a command * <CR> is the meaning of 0x0D.

SIDVD<CR> : Select Input source DVD

MSSTEREO<CR> : surround Mode Set to STEREO

MVUP<CR> : Master Volume UP

PWON<CR> : system PoWer ON

PWSTANDBY<CR> : system PoWer STANDBY

SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’

- 6 -

Others

A) COMMAND is receivable also during transmission of EVENT.

B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels

returns as EVENT.

C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,

the data of an intact channel is set to "50".

D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (andalso the value of the channel

volume of all channels , It described in B) ) returns as EVENT.

E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME

does NOT return.

F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.

G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.

H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to

the another request commands(ex. SV command).

I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”.

J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three

ASCII characters as bellows.

Ex. MASTER VOLUME = +1.0dB : MV81<CR>

+0.5dB : MV805<CR>

0dB : MV80<CR>

-0.5dB : MV795<CR>

-1.0dB : MV79<CR>

| |

-79.5dB : MV005<CR>

-80.0dB : MV00<CR>

-80.5dB : MV995<CR>

--- : MV99<CR>

* At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual.

K) 1 seconds later, please transmit the next COMMAND after transmitting a power on COMMAND（PWON）.

- 7 -

COMMAND and PARAMETER list

COMMAND PARAMETER function example

PW ON POWER ON/STANDBY change PWON<CR>

STANDBY PWSTANDBY<CR>

? Return PW Status PW?<CR>

MV UP MASTER VOLUME UP/DOWN , direct change to **dB MVUP<CR>

DOWN MVDOWN<CR>

** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) 995=-80.5dB MV80<CR>

? Return MV Status MV?<CR>

CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP<CR>

FL DOWN ---FRONT Lch CVFL DOWN<CR>

FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50<CR>

FR UP CVFR UP<CR>

FR DOWN ---FRONT Rch CVFR DOWN<CR>

FR ** **:38 to 62 by ASCII , 50=0dB CVFR 50<CR>

C UP CVC UP<CR>

C DOWN ---CENTERch CVC DOWN<CR>

C ** **:38 to 62 by ASCII , 50=0dB CVC 50<CR>

SW UP CVSW UP<CR>

SW DOWN ---SUBWOOFERch CVSW DOWN<CR>

SW ** **:38 to 62 by ASCII , 50=0dB,00=OFF CVSW 50<CR>

SL UP CVSL UP<CR>

SL DOWN ---SURROUND Lch CVSL DOWN<CR>

SL ** **:38 to 62 by ASCII , 50=0dB CVSL 50<CR>

SR UP CVSR UP<CR>

SR DOWN ---SURROUND Rch CVSR DOWN<CR>

SR ** **:38 to 62 by ASCII , 50=0dB CVSR 50<CR>

SBL UP ---SURROUND BACK Lch (SBch 2SP) CVSBL UP<CR>

SBL DOWN CVSBL DOWN<CR>

SBL ** **:38 to 62 by ASCII , 50=0dB CVSBL 50<CR>

SBR UP ---SURROUND BACK Rch (SBch 2SP) CVSBR UP<CR>

SBR DOWN CVSBR DOWN<CR>

SBR ** **:38 to 62 by ASCII , 50=0dB CVSBR 50<CR>

MV, CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)

- 8 -

COMMAND PARAMETER function example

CV SB UP ---SURROUND BACKch (SBch 1SP) CVSB UP<CR>

SB DOWN CVSB DOWN<CR>

SB ** **:38 to 62 by ASCII , 50=0dB CVSB 50<CR>

FHL UP CVFHL UP<CR>

FHL DOWN ---FRONT HEIGHT Lch CVFHL DOWN<CR>

FHL ** **:38 to 62 by ASCII , 50=0dB CVFHL 50<CR>

FHR UP CVFHR UP<CR>

FHR DOWN ---FRONT HEIGHT Rch CVFHR DOWN<CR>

FHR ** **:38 to 62 by ASCII , 50=0dB CVFHR 50<CR>

? Return CV Status CV?<CR>

MU ON OUTPUT MUTE ON/OFF change MUON<CR>

OFF MUOFF<CR>

? Return MU Status MU?<CR>

SI CD Select INPUT source SICD<CR>

TUNER SITUNER<CR>

DVD SIDVD<CR>

BD SIBD<CR>

TV SITV<CR>

SAT/CBL SISAT/CBL<CR>

DVR SIDVR<CR>

GAME SIGAME<CR>

GAME2 SIGAME2<CR>

V.AUX SIV.AUX<CR>

DOCK SIDOCK<CR>

IPOD Select iPod (dock or USB) and PLAY SIIPOD<CR>

CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)

- 9 -

COMMAND PARAMETER function example

SI NET/USB SINET/USB<CR>

RHAPSODY (North America model Only) SIRHAPSODY<CR>

NAPSTER (North America & Europe model Only) SINAPSTER<CR>

PANDORA (North America model Only) SIPANDORA<CR>

LASTFM (Europe model Only) SILASTFM<CR>

FLICKR SIFLICKR<CR>

FAVORITES SIFAVORITES<CR>

IRADIO SIIRADIO<CR>

SERVER SISERVER<CR>

USB/IPOD Select USB or iPod Direct SIUSB/IPOD<CR>

USB Select INPUT source NET/USB and USB Start Playback SIUSB<CR>

IPD Select INPUT source NET/USB and iPod Direct Start Playback SIIPD<CR>

IRP Select INPUT source NET/USB and Internet Radio Start Playback SIIRP<CR>

FVP Select INPUT source NET/USB and Favorites Start Playback SIFVP<CR>

? Return SI Status SI?<CR>

ZM ON MAIN ZONE ON/OFF change ZMON<CR>

OFF ZMOFF<CR>

? Return ZM Status ZM?<CR>

SR CD REC SELECT mode set , and select source SRCD<CR>

| ---The name of PARAMETER is |

USB/IPOD the same as that of the time of SI COMMAND. SRUSB/IPOD<CR>

SOURCE REC SELECT mode cancel SRSOURCE<CR>

? Return SR Status SR?<CR>

- 10 -

COMMAND PARAMETER function example

SD AUTO set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) SDAUTO<CR>

HDMI set force HDMI INPUT mode SDHDMI<CR>

DIGITAL set force DIGITAL INPUT (Optical,Coaxial)mode SDDIGITAL<CR>

ANALOG set force ANALOG INPUT mode SDANALOG<CR>

? Return SD Status SD?<CR>

DC AUTO set DIGITAL INPUT AUTO mode DCAUTO<CR>

PCM set DIGITAL INPUT force PCM mode DCPCM<CR>

DTS set DIGITAL INPUT force DTS mode DCDTS<CR>

? Return DC Status DC?<CR>

SV DVD VIDEO SELECT mode set , and select source SVDVD<CR>

BD SVBD<CR>

TV SVTV<CR>

SAT/CBL SVSAT/CBL<CR>

DVR SVDVR<CR>

GAME SVGAME<CR>

GAME2 SVGAME2<CR>

V.AUX SVV.AUX<CR>

DOCK SVDOCK<CR>

SOURCE VIDEO SELECT mode cancel SVSOURCE<CR>

? Return SV Status SV?<CR>

SLP OFF MAIN ZONE SLEEPTIMER setting SLPOFF<CR>

*** ***:001 to 120 by ASCII , 010=10min SLP120<CR>

? Return SLP Status SLP?<CR>

Otros manuales para AVR-2312CI

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Receptor de Denon

Denon

Denon AVR-789 Dimensiones

Denon

Denon MULTEQXT AVR-4306 Manual de usuario

Denon

Denon AVR-1804 Manual de usuario

Denon

Denon AVR-S700W Manual de usuario

Denon

Denon AVR-X500 Manual de usuario

Denon

Denon AVR 788 - AV Receiver Manual de usuario

Denon

Denon AVR-X4300H Manual de usuario

Denon

Denon AVR-X1200W Manual de usuario

Denon

Denon AVR-588 Manual de usuario

Denon

Denon AVR-X520BT Manual de usuario

Denon

Denon AVR-X6200W Manual de usuario

Denon

Denon AVR-S530BT Manual de usuario

Denon

Denon AVR-X1100W Manual de usuario

Denon

Denon AVR-X6500H Manual de usuario

Denon

Denon AVR-3803 Manual de usuario

Denon

Denon AVR 788 - AV Receiver Guía del usuario

Denon

Denon DRA-100 Manual de usuario

Denon

Denon RCD-M40 Manual de usuario

Denon

Denon AVR-2808 Manual de usuario

Denon

Denon AVR-1802/882 Manual de usuario

Denon

Denon AVR-3808CI Manual de uso y cuidado

Denon

Denon AVR-E400 Manual de usuario

Denon

Denon AVR-1707 Manual de usuario

Denon

Denon AVR-2113 Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario