DELTALOGIC ACCON-NetLink-PRO Manual de usuario
User Manual
ACCON-NetLink-PRO compact
ACCON-NetLink-PRO compact 1
This manual is for project developers, users and assemblers who utilize
the ACCON-NetLink-PRO compact.
It shows the user the handling of the ACCON-NetLink-PRO compact and
explains signaling functions. All necessary data for assembling should be
provided to the assembler. © 1995 - 2016
DELTA LOGIC Automatisierungstechnik GmbH
Stuttgarter Strasse 3
73525 Schwaebisch Gmuend
Germany
Phone sales: +49-(0)7171-916-120
Phone support: +49-(0)7171-916-112
Fax sales: +49-(0)7171-916-220
Fax support: +49-(0)7171-916-212
E-Mail sales: sales@deltalogic.de
E-Mail support: support@deltalogic.de
www.deltalogic.de
All rights reserved. No part of this work is allowed to be copied, reproduced, conferred,
processed and stored into electronic media or translated into any other language without a
written permission of the author.
STEP®, TIA®, TIA Portal®, S7-200®, S7-300®, S7-400®, HMI®, STEP® and SIMATIC® are
registered trademarks of Siemens AG, ACCON® and DELTALOGIC® are registered trademarks
of DELTA LOGIC Automatisierungstechnik GmbH.
Note:
We have checked the content of this manual for conformity with the hardware and software
described. Nevertheless, because deviations cannot be ruled out, we cannot accept any
liability for complete conformity. The data in this manual have been checked regularly and
any necessary corrections will be included in subsequent editions. We always welcome
suggestions for improvement.
Last update 2016-09-26. All technical changes reserved.
ACCON-NetLink-PRO compact 2
TABLE OF CONTENTS
1TECHNICAL DESCRIPTION.......................................... 3
2SCOPE OF DELIVERY................................................... 5
3DEVICE DESCRIPTION ................................................ 6
4REQUIREMENTS FOR OPERATING.............................. 8
5COMMISSIONING ...................................................... 9
6TCP/IP PARAMETRIZATION .....................................13
7BUS SETTINGS..........................................................17
8COMMUNICATION VIA RFC1006 (S7-TCP/IP)...........25
9THE WEB INTERFACE ...............................................33
10 REMOTE MAINTENANCE WITH THE ACCON-NETLINK-
PRO COMPACT ........................................................44
11 TROUBLE SHOOTING ...............................................45
12 FREQUENTLY ASKED QUESTIONS.............................47
13 TECHNICAL DATA.....................................................50
14 APPENDIX................................................................54
ACCON-NetLink-PRO compact 3
1TECHNICAL DESCRIPTION
ACCON-NetLink-PRO compact is a handy communication and
programming adaptor between PC and S7 controllers. The electronics of
the ACCON-NetLink-PRO compact is placed in a PROFIBUS plug's case.
Thus, the adapter is very small and handy.
As all-rounder, the ACCON-NetLink-PRO compact can be connected to
the PLC via MPI, PROFIBUS and PPI. The ACCON-NetLink-PRO compact
independently detects the current bus settings of the PLC.
The ACCON-NetLink-PRO compact's communication to the PC is carried
out via TCP/IP. The configuration of the ACCON-NetLink-PRO compact
can be created and changed via its integrated web site. For security
reasons the access to the web site is protected by a password.
The ACCON-NetLink-PRO compact supports the S7 communication via
RFC1006 (ISO on TCP). Thus TCP/IP communication processors (e. g.
CP343-1) can be replaced by this adapter. But projected connections are
not supported. Furthermore the ACCON-NetLink-PRO compact supports
the parametrization of DP-Slaves via DP-V1 (Class 2). A driver for
SIMATIC applications (ACCON-S7-NET) is included in delivery. The
ACCON-NetLink-PRO compact is fed via the bus connection.
Alternatively, the device can be externally supplied via 24 VDC.
The ACCON-NetLink-PRO compact can be connected to the PC via a hub
or switch or directly with the supplied patch cable (Cross-Link).
ACCON-NetLink-PRO compact 4
Features:
•Automatic bus profile detection
•Full PROFIBUS speed up to 12 Mbps
•Extended diagnostics
•Support of MPI, PROFIBUS and PPI
•Supports DHCP
•Support of Slave programming via DP-V1 (Class 2)
•Supports all established SIMATIC Engineering Tools
•Supports ISO on TCP (RFC 1006)
•Voltage feed from the PLC or controller
•External 24-V power supply possible
•Plug with PG bushing
•Applicable up to 60 °C
ACCON-NetLink-PRO compact 5
2SCOPE OF DELIVERY
•ACCON-NetLink-PRO compact
•Patch cable (Cross-Over, 3 meters)
•DELTA LOGIC Automatisierungstechnik-DVD including ACCON-S7-
NET-Driver
Suitable accessories can be found on www.deltalogic.de.
ACCON-NetLink-PRO compact 6
3DEVICE DESCRIPTION
Figure 1: ACCON-NetLink-PRO compact
1. RJ45 bushing to connect the device to the Ethernet
2. Status LEDs for the Ethernet-Interface
3. Status LEDs
4. Power supply bushing for 24 VDC. Please keep the polarity in mind.
5. Bus plug with PG bushing
6. Patch cable (Cross-Over, 3 meters)
1
2
3
4
5
6
ACCON-NetLink-PRO compact 7
Start of the ACCON-NetLink-PRO compact
In the first seconds after starting the ACCON-NetLink-PRO compact the
Power LED lights blue. The start procedure will be finished after about
20 seconds then the device is ready to operate.
LED display
POWER LED ACTIVE LED BUS LED
Ready to operate BLUE
Trying to log in on the
device at the bus BLUE ORANGE
BLINKING
Device is logged in on
the bus BLUE GREEN
Data exchange with a
controller (Data) BLUE GREEN
BLINKING
Table 1: Status LEDs
POWER LED ACTIVE LED BUS LED
Transmitting
firmware update
BLUE
BLINKING RED
BLINKING
Table 2: Status LEDs Firmware Update
LINK LED GRÜN ACTIVE LED GELB
No Ethernet
connection OFF OFF
Ethernet activity ON BLINKING
Table 3: Status LEDs Ethernet
ACCON-NetLink-PRO compact 8
4REQUIREMENTS FOR OPERATING
Hardware
Siemens S7-200-, S7-300 and S7-400 automation devices or compatible
to S7. The utilized PCs must have a working network connection via
TCP/IP. Also the network configuration must be known. Usual network
cards are suitable.
Software
To use the ACCON-S7-NET drivers you need a PC including Windows XP,
2003R2, 7, 2008R2, 8.1, 2012R2, 10. On this PC the SIMATIC Device
Drivers (PG/PC-Interface) have to be installed. The SIMATIC Device
Drivers will be installed with e. g. STEP 7, STEP 7 lite or STEP 7-
Micro/Win. By installing ACCON-S7-NET more interfaces will be added
to the PG/PC-Interface.
Take care of your Firewall Settings. The ACCON-NetLink-PRO compact
uses the TCP ports 7777 and 102 (RFC1006). The Device Search function
uses the UDP ports 25342 and 25343. The default IP address of the
ACCON-NetLink-PRO compact is 192.168.4.49.
Assembly
Installation and assembly have to be carried out according to
VDE 0100 / IEC 364. As the ACCON-NetLink-PRO compact is an IP30
module it has to be built into a switch cabinet.
For secure operating please keep the maximum ambient temperature of
60 °C in mind.
ACCON-NetLink-PRO compact 9
5COMMISSIONING
The ACCON-NetLink-PRO compact is shipped with the IP address
192.168.4.49.
Connection to the automation device
Connect the 9-pin SUB-D plug to the MPI or PROFIBUS interface of your
S7 controller.
Connection to the PC via RJ45 Ethernet-Interface
Put one end of the patch cable into the Ethernet bushing of your
ACCON-NetLink-PRO and the other end into a hub or switch which is
connected to your PC's network card.
You can also directly connect the ACCON-NetLink-PRO compact to your
PC's network card without a switch.
Installation software
After inserting the DELTA LOGIC Automatisierungstechnik-DVD please
start the data file SetupAcconS7Net.exe for the ACCON-S7-NET driver
(<DVD-drive>\S7-Adapter).
For an installation you have to be logged in as administrator.
Set PG/PC-Interface
1. Open the SIMATIC PG/PC interface from the windows control panel.
The following points have to be in the dialog «Set PG/PC Interface«:
- ACCON-S7-NET NLPro(MPI)
- ACCON-S7-NET NLPro(PPI)
- ACCON-S7-NET NLPro(PROFIBUS)
Tabla de contenidos
Otros manuales de Adaptador de DELTALOGIC
