PROG
1
34
2
Alkalines 1,5V
LR03 (AAA)
1
7
P1
P6
5°C
30°C
00:00
23:45
P1
P6
6.00 8.0011.00 13.00 17.00 23.000.00
P1 P2 P3 P4 P5 P6
PROG x7
PROG
6.00
16°C 16°C
19°C 20°C 20°C
18°C 18°C
8.00 11.00 13.00 17.00 23.000.00
P1 P2 P3 P4 P5 P6
16°C 16°C
20°C 20°C
18°C 18°C
5°C
30°C
00:00
23:45
00:00
23:45
PROG 5+2
1
2
1
2
3
1...5
6/7
1
2
3
4
5
6
7
8
9
3
7.00
16°C 16°C20°C
23.000.00
P1 P6
1
3
2
PROG 5+2
EXIT
EXIT
EXIT
PROG x 7
A
B
COPY
OR
>3s
6.00
16°C 16°C
20°C 20°C 20°C
18°C
8.00 11.00 13.00
13.54
17.00 23.000.00
P1 P2 P3 P4 P5 P6
13.54
AUTO
PROG
7.00
16°C 16°C20°C
23.000.00
P1 P6
21°C
18°C
❶ ❷ ❸
When the batteries symbol appears. you have
approximately 1 month to change the batteries
(2 1.5 V LR03 or AAA alkaline batteries).
You have approximately 30 seconds to change
the batteries before the time setting is reset
(if this happens, reprogramme the date and time).
Override
From AUTO mode or the «day at home» programme
Allows a given temperature setting to be applied until the next change of programme.
Conrm and continue on to the next day to program
it separately or conrm the program and copy it to
the next day.
E.g.
The program can be modied for each day.
Use the + and - buttons to make your choices.
Press OK to conrm and move on to the next setting
2 daily programmes: week (1 to 5) + weekend (6 and 7).
1 single programme for the 5 weekdays.
1 single programme for the weekend.
To change the programme, see above.
To apply a simplied program (two programmable periods, P1 and P6). This program can be modied.
To exit the mode,
turn the selector dial.
To exit the mode,
turn the selector dial.
Periods 2 to 5 can be disabled.
e.g. disabling of the midday slot (periods 3 and 4).
❶Select the programme stage to be disabled
(e.g.: P3)
❷Repeatedly press the - button until the display
shows «--:--»
❸ Conrm by pressing OK.
Repeat the operation for each time slot of
the programme that you wish to disable.
The programme may be weekly (PROG x7) or
daily (PROG 5+2). This choice is made using the switch
on the back of the device.
This programming can also be done in one-hour,
half-hour, or quarter-hour stages.
If you wish to change these settings, refer to the
«installation guide» or contact your installation engineer.
Programming can be done for one-hour, 30-minute or 15-minute
time slots (see «installation guide», menu 1-02).
❶Turn the selector dial to PROG
❷ Press the - button to display the ashing symbol
❸ Conrm by pressing OK
Congure the «day at home» programme using the + and - buttons,
then press OK to conrm and move on to the next setting.
