Dell POWERCONNECT 2800 Series Manual de usuario
CALLN HOSTED CALL RECORDING
PORT MIRRORING SETUP
DELL POWERCONNECT 2800
SERIES
Created by Chris Lane
15 November 2017
Version 1.0.1
Dell PowerConnect 2800 Series Port Mirroring setupRevision 1.0.1 Page 2 of 5
Table of Contents
1. Introduction .........................................................................................................................3
2. Connectivity..........................................................................................................................4
3. Configuration of Port Mirroring ................................................................................5
Dell PowerConnect 2800 Series Port Mirroring setupRevision 1.0.1 Page 3 of 5
1. Introduction
This document describes how to configure your DELL PowerConnect 2800 series network switch to work
with CallN. All switches in the DELL PowerConnect 2800 series have an identical interface and for the
purposes of this guide, are interchangeable.
Dell PowerConnect 2800 Series Port Mirroring setupRevision 1.0.1 Page 4 of 5
2. Connectivity
To successfully record calls, the DELL switch needs to be placed into the network where it will be able to
record all VOIP traffic. This could mean the VOIP traffic is connected directly to the DELL switch and
phones are connected to the switch as well, or the VOIP traffic is connected to the DELL switch which is
then connected to other switches which phones connect.
The CallN recording computer requires two network connections. One network connection is connected
to the destination port of the port mirror configuration. Typically, this will be the last port on your switch,
but can be a nominated port at the time of configuring port mirroring.
The second port is a standard connection to the LAN which allows CallN to upload voice recordings to the
CallN portal.
Dell PowerConnect 2800 Series Port Mirroring setupRevision 1.0.1 Page 5 of 5
3. Configuration of Port Mirroring
The DELL PowerConnect 2800 Series of network switch has an Unmanaged Mode, a Managed Mode and
a Secure Mode. By default, a new switch will be in Unmanaged Mode. In this mode there is no web
interface to configure the switch. The switch must be in Management Mode to configure. To change the
switch to Managed Mode, press the Mode button for up to 7 seconds.
Connect a computer to switch and put the computer into the same subnet as the switch. By default, the
switch IP Address is 192.168.2.1 with a subnet mask of 255.255.255.0. Enter in the username and
password when prompted. The default username is Admin and has no password.
Once the interface is open, expand the Switch menu on the left, and then expand the Ports menu. From
the list select Port Mirroring.
Select Add to open the “Add Source Port” page.
Set the Destination Port from the drop down list. This is the port the Recording Computer will listen to
traffic on and record calls. Ports are listed with a preceding ‘g’. For example, port 1 will show as g1.
Set Source Port from the drop down list. This is the port on the switch that leads back to a PBX or
internet connection but it needs to be a port that will see all VOIP traffic.
Set Type to “Tx and Rx” from the drop down list. By setting it to “Tx and Rx” the switch will copy all
received and sent traffic to the destination port. If it is not set to this, only one party of call will be
recorded.
Press Apply Changes.
NOTE:
▪Source ports and destination port cannot be a LAG member.
▪A source port cannot be a destination port and a destination port cannot be a source port.
▪A destination port is not a VLAN member.
▪GVRP is not enabled on the destination port.
▪Only one destination port can be defined.
Port mirroring is now configured. New calls will now be recorded and uploaded to your CallN portal.
Tabla de contenidos
Otros manuales de Cambiar de Dell
Dell
Dell PowerConnect 8024 Manual de usuario
Dell
Dell OptiPlex Powered USB HUB Manual de instalación y operación
Dell
Dell Networking S4810 Manual de usuario
Dell
Dell PowerConnect J-EX8208 Instrucciones de instalación
Dell
Dell Z9000 Manual de usuario
Dell
Dell POWERCONNECT J SERIES Manual de usuario
Dell
Dell EMC Edge 510 LTE Manual de usuario
Dell
Dell Z9000 Manual de usuario
Dell
Dell X1000 Series Manual de usuario
Dell
Dell PowerConnect M8428-k Cómo utilizar
Dell
Dell PowerEdge 180AS Manual de usuario
Dell
Dell EMC PowerSwitch S5148F-ON Manual de usuario
Dell
Dell S5048F-ON Manual de uso y cuidado
Dell
Dell PowerConnect W-Series FIPS Manual del propietario
Dell
Dell PowerConnect J-EX4200-24T Guía de inicio rápido
Dell
Dell N20xx Series Manual de usuario
Dell
Dell PowerConnect 8024 Manual de usuario
Dell
Dell PowerEdge M1000e Manual de usuario
Dell
Dell S4048-ON Manual de usuario
Dell
Dell PowerConnect 3248 Manual de usuario
