Dell PowerVault NX1950 Manual de usuario
www.dell.com | support.dell.com
Dell™ PowerVault™
NX1950 Systems
Getting Started With
Your System
Guide de mise en route
Primeiros passos com o sistema
Procedimientos iniciales con el sistema
Model EMU01
www.dell.com | support.dell.com
Dell™ PowerVault™
NX1950 Systems
Getting Started With
Your System
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
_________________
Information in this document is subject to change without notice.
© 2006 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and PowerVault are trademarks of Dell Inc.; Intel and Xeon are registered trademarks
of Intel Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Model EMU01
September 2006 P/N NR698 Rev. A00
Getting Started With Your System 3
System Features
The major hardware and software features of your system include:
• Two Dual Core Intel
®
Xeon
®
processor 5000 Sequence.
• 4 GB of 667 MHz, Fully Buffered DIMMs (FBD), upgradable to a maximum of 8 GB.
The system also features redundant memory, which provides memory sparing or memory mirroring.
Either feature is available if eight identical memory modules are installed.
• 15000 rpm hard drives configured into a RAID1 array for fault tolerant operating system operations.
• A slimline DVD-ROM, or DVD-ROM/ CD-RW drive.
• Two hot-pluggable, 670-W power supplies in a 1 + 1 redundant configuration.
• Four fan modules, each comprised of two dual-rotor fans, for a total of eight cooling fans.
The system board includes the following features:
• Two riser cards (left and center risers), each providing a x8 lane width PCI-Express expansion slot.
• Dedicated PCI slot for an integrated RAID controller card with 256 MB of
cache memory and
a RAID battery.
• Four integrated Gigabit Ethernet NICs capable of supporting 10-Mbps, 100-Mbps, 1000-Mbps,
and 2-Gbps data rates.
• Two x4 SAS ports for connectivity to storage subsystem or two 4-Gbps Fibre Channel ports
for connectivity to a storage area network (SAN).
• Four USB 2.0-compliant connectors (two on the front and two on the back)
capable of external
support for
a diskette drive, a CD-ROM drive, a keyboard, a mouse, or a USB flash drive.
• Remote access controller (RAC) for remote systems management.
•
An integrated VGA-compatible video subsystem with an ATI ES1000, 33-MHz PCI video
controller. This video subsystem contains a minimum of 16MB of graphics memory with support
for 2D graphics. Maximum resolution is 1600x1200 with 65,536 colors; true-color graphics are
supported in the following resolutions: 640 x 480, 800 x 600, 1024 x 768, 1280 x 1024. When the
optional remote access card is installed, the maximum video resolution is 1280x1024
.
• Systems management circuitry that monitors operation of the system fans as well as critical system
voltages and temperatures. The systems management circuitry works in conjunction with the systems
management software.
• Back-panel connectors include serial, video, two USB connectors, four NIC connectors, two SAS
(or Fibre Channel in gateway mode connectors), and one NIC connector for RAC access.
• Front-panel connectors include a video and two USB connectors.
• Front-panel 1x5 LCD for system ID and error messaging.
For more information about specific features, see Technical Specifications.
4Getting Started With Your System
Supported Operating System
Your system supports Microsoft®Windows®Unified Data Storage Server 2003 Standard and Enterprise
x64 Editions operating system.
Other Information You May Need
CAUTION: The Product Information Guide provides important safety and regulatory information.
Warranty information may be included within this document or as a separate document.
• The
Rack Installation Guide
or
Rack Installation Instructions
included with your rack solution
describes how to install your system into a rack.
• The
Hardware Owner’s Manual
provides information about system features and describes how
to troubleshoot the system and install or replace system components. This document may be found
on the CDs that came with your system or at
support.dell.com
.
• CDs included with your system provide documentation and tools for configuring and managing
your system.
• Updates are sometimes included with the system to describe changes to the system, software,
and/or documentation.
NOTE: Always check for updates on support.dell.com and read the updates first because they often
supersede information in other documents.
• Release notes or readme files may be included to provide last-minute updates to the system or
documentation or advanced technical reference material intended for experienced users or technicians.
Obtaining Technical Assistance
If you do not understand a procedure in this guide or if the system does not perform as expected,
see your Hardware Owner’s Manual.
Dell Enterprise Training and Certification is available; see www.dell.com/training for more information.
This service may not be offered in all locations.
Installation and Configuration
CAUTION: Before performing the following procedure, read and follow the safety instructions and important
regulatory information in your Product Information Guide.
This section describes the steps to set up your system for the first time.
Getting Started With Your System 5
Unpacking the System
Unpack your system and identify each item.
Keep all shipping materials in case you need them later.
Installing the Rail and System in a Rack
Install the system in the rack once you have read the "Safety Instructions" located in the rack
installation documentation for your system.
See your rack installation documentation for instructions on installing your system in a rack.
6Getting Started With Your System
Connecting the Keyboard, Mouse, and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which cable to plug into each
connector. Be sure to tighten the screws (if any) on the monitor's cable connector.
NOTE: If you simultaneously connect two monitors to the system, using the front and rear video
connections, the video will default to the front since only one display can operate at a time.
Connecting the Power
Connect the system’s power cable(s) to the system.
Plug the other end of the cable into a grounded electrical outlet or a separate power source
such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).
Getting Started With Your System 7
Installing the Power Cord Retention Bracket (Optional)
Attach the power cord retention bracket on the right bend of the power supply handle. Bend the
system power cable into a loop as shown in the illustration and attach to the bracket’s cable clasp.
Repeat the procedure for the second power supply.
Plug the other end of the power cables into a grounded electrical outlet or a separate power source
such as an UPS or a PDU.
Turning on the System
Turn on the system and monitor (optional).
Press the power button on the system and the monitor. The power indicators should light.
Adjust the monitor's controls until the displayed image is satisfactory.
8Getting Started With Your System
Installing the Bezel
Install the bezel (optional).
Complete the 0perating System Setup
The operating system is preinstalled on your system. To reinstall the operating system,
see the documentation that is shipped along with your system.
Technical Specifications
Processor
Processor type Two dual-core Intel Xeon processors 5100 Sequence
Expansion Bus
Bus type PCIe
PCIe Risers Two x8 lane width
Memory
Architecture PC2-5300 667 MHz fully-buffered DIMMs with ECC protection,
with two-way lockstep operation
Memory module sockets Eight 240-pin
Minimum RAM 4 GB (four 1 GB modules)
Maximum RAM 8 GB
Otros manuales para PowerVault NX1950
15
Tabla de contenidos
Idiomas:
Otros manuales de Almacenamiento de Dell
Dell
Dell PowerVault 136T Manual del propietario
Dell
Dell SC5020 Instrucciones de uso
Dell
Dell PowerVault MD3060e Series Manual técnico
Dell
Dell FS7500 Manual de usuario
Dell
Dell PowerVault 201S Manual de usuario
Dell
Dell PowerVault MD3200 Series Instrucciones de instalación
Dell
Dell EMC NX3240 Manual de usuario
Dell
Dell PowerVault 35F Manual de usuario
Dell
Dell PowerVault 200S Guía
Dell
Dell VERLAND TANDBERG Titan T2000 Manual de usuario
Dell
Dell PowerVault 124T Manual de usuario
Dell
Dell PowerVault 220S Manual de usuario
Dell
Dell PowerVault NX300 Manual de usuario
Dell
Dell SCv2080 Manual de usuario
Dell
Dell PowerVault TL4000 Manual de usuario
Dell
Dell PowerVault RD1000 Manual de funcionamiento
Dell
Dell PowerVault 120T DLT1 Manual técnico
Dell
Dell PowerVault NX1950 Manual de usuario
Dell
Dell PowerVault DL2000 Manual de usuario
Dell
Dell PowerVault RD1000 Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario