Dell PowerEdge C1100 Guía rápida

www.dell.com | support.dell.com

Dell™ PowerEdge™ Systems

Using the Baseboard

Management Controller

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, PowerEdge are trademarks of Dell Inc.; Microsoft, Windows, and Internet Explorer are

registered trademarks of Microsoft Corporation; Linux is the registered trademark of Linus Torvalds; Java is a registered trademark of Sun

Microsystems, Inc. or its subsidiaries in the United States and other countries.in the United States and other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

December 2009 Rev. A00

Contents 3

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

BMC key Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . 5

Using the Web UI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Logging into the Web User Interface . . . . . . . . . . . . . . . . . . . . . . . 6

System Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

System Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Component Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

System Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Fan Probes Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Temperature Probes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Voltage Probes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Console Redirection and Virtual Media . . . . . . . . . . . . . . . . . . 12

iBMC KVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

iBMC Virtual Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Virtualizing Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Mapping a Virtual Media Drive . . . . . . . . . . . . . . . . . . . . . . . 16

Unmapping a Virtual Media Drive . . . . . . . . . . . . . . . . . . . . . 16

Console Redirect Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 16

Email Alert Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Network Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Platform Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Serial Over LAN Configuration . . . . . . . . . . . . . . . . . . . . . . . 20

Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4Contents

Web Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

SSL Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Platform Event Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

IPMI 1.5 / 2.0 Command Support List. . . . . . . . . . . . . . . . . . . . . . . 24

Using the Baseboard Management Controller 5

Introduction

This section introduces the A BMC and includes the requirements for web-based graphical user

interface (GUI), keyboard, video, and mouse (KVM), and virtual media.

BMC Key Features and Functions

The following lists the supported features of the BMC:

• IPMI v1.5 and v2.0

• Out-of-band monitoring and control for sever management over LAN

• Dedicated 10/100 NIC for remote management over a network

• Information report includes main board part number, product name, manufacturer, etc.

• Health status/hardware monitoring report

• Events log, view, and clear

• Event notification using chassis LED indicator and Platform Event Trap (PET)

• Platform Event Filtering (PEF) to take selected action for selected events, including NMI and

SMI

• Chassis management including power control and status report, front panel buttons, LED

control, Secure Mode, and Boot Option

• Watchdog and auto server re-start and recovery

• Multi-session user and alert destination for LAN channel

• IPMB connector to enable advanced server management communication with BMC

Using the Web UI

The BMC firmware features an embedded web server, enabling users to connect to the BMC using

an Internet browser (Microsoft

Internet Explorer™) without needing to install KVM and virtual

storage software on a remote console.

Web-based GUI is supported on the following browsers:

Microsoft Windows:

• Internet Explorer 6 and 7

• Mozilla

Firefox

2.0 or later

Linux:

Mozilla Firefox 2.0 or later

NOTE: Before using the web user interface, ensure that the firewall settings are configured to enable

access to the following ports: 8890 (KVM), 9000 (storage), 9001, 9002, and 9003.

6Using the Baseboard Management Controller

www.dell.com | support.dell.com

Logging into the Web User Interface

Enter the BMC-embedded server IP address or URL into the address bar of the web browser. The

BMC interface has a default of (DHCP\Static). Enter the system BIOS setup with <F2> to

change these settings.

When connecting to the BMC, the login screen prompts for the username and password. This

authentication with Secure Sockets Layer (SSL) protection prevents unauthorized intruders from

gaining access to the BMC web server. Once authentication is passed, you can manage the server by

privilege. At the same time, the PHP Hypertext Preprocessor (PHP) records all user information,

including user ID and privilege.

System Features

System Summary

The

System Summary

tab enables you to view the firmware version, hardware version, and IPv4

information. Click the

System

tab to view the Remote Management Controller.

Table 1-1. BMC Information

BMC Information Description

Date/Time Current time in the form:

Day MMM DD HH:MM:SS:HH YYYY

Firmware Version Dell Remote Management Controller firmware version.

Firmware Updated Date the firmware was last flashed in the form:

Day MMM DD HH:MM:SS:HH YYYY

MAC Address MAC address for the Baseboard Management Controller.

Table 1-2. IPv4 Information

IPv4 Information Description

Enabled Yes or No

IP Address The 32-bit address that identifies the NIC to a host. The value is in

the dot separated format, such as 143.166.154.127.

Gateway The address of a router or a switch. The value is in the dot separated

format, such as 143.166.154.1.

Subnet Mask The Subnet Mask identifies the parts of the IP Address that are the

Extended Network Prefix and the Host Number. The value is in the

dot separated format, such as 255.255.0.0.

Using the Baseboard Management Controller 7

Component Information

Server Board Information

Including Serial Number, BIOS Version, Product ID, Manufacturer and Manufacture Date.

CPU Information

Including CPU ID, Status, Socket, Manufacturer, Model and Frequency.

Memory Information

Including Memory ID, Status, Socket, Module Size, Model and Frequency.

Power Management

This feature enables the administrator to power on or power down the system remotely.

Select a

Power Control Operation

Click

Apply

to enable the selected

Power Control Operation

System Event Log

The System Event Log (SEL) page displays system events that occur on the managed system. The

SEL is generated by the Baseboard Management Controller (iBMC) or BIOS on the managed

system.

Table 1-3. Power Status

Power Status Description

Power Status Yes or No

Table 1-4. Power Control Operation Options

Power Control Operation Description

Power On System Powers on the system.

Power Off System Powers off the system.

Reset System Reboots system without powering off (warm boot).

Power Cycle

System

Powers off, then reboots system (cold boot).

NMI Sends Non-Masking Interrupt to halt system operation.

Soft Shutdown Shuts down system.

8Using the Baseboard Management Controller

www.dell.com | support.dell.com

The SEL lists the following information about system events: severity, a date/time stamp, and a

short description. The list can be sorted by clicking any column heading in the SEL. Subsequent

clicks on the column headings reverse the sort order.

Table 1-5 describes the severity conditions by icon.

Click

System Event Log

to view specific event information. Table 1-6 shows the available functions

located at the top right corner of the screen.

Table 1-5. Severity Condition Icons

Icon Description

Normal event

Non-critical event

Critical event

Unknown

Table 1-6. System Event Log Functions

Function Description

Print Prints the SEL in the sort order that appears on screen.

Clear Log Clears the SEL.

NOTE: The Clear Log button only appears if you have permission.

Save As Opens a pop-up window that enables you to save the SEL to a

directory of your choice. The severity of the condition is indicated and

saved in the log file.

The Date/Time is stored in ascending order. Blank dates from the

screen are saved as <System Boot>in the file.

Refresh Reloads the SEL page

Using the Baseboard Management Controller 9

Firmware Update

Use the Firmware Update feature to upgrade to the latest firmware version. The following data is

included in the iBMC firmware package:

• Compiled iBMC firmware code and data

• Web-based user interface, JPEG, and other user interface data files

• Default configuration files

NOTE: The firmware update retains the current iBMC settings.

Updating the iBMC Firmware

NOTE: Before beginning the firmware update, download the latest firmware version and save it on your

local system. During the process of firmware update, the AC power of the managed system cannot be

unplugged and the Web GUI cannot be closed.

Browse to, or Enter the path on your system where the firmware image file resides.

Example:

C:\Updates\V1.0\<image_name>

The default firmware image name is

firmimg.ast2050.dcs

Select the

Update Type

Normal

Forced

(The default value is

Normal

Normal:

An update operation will occur only when the BMC validates the target board, target

product and version number.

Forced:

Forced update makes the BMC update the image without validating target board,

target product and version number.

Click

Update

The update might take several minutes. When the update is completed, a dialog box appears.

Click

to close the session and automatically log out.

After the iBMC resets, click

to log in to the iBMC again.

Sensors

The

Sensor

menu provides information about system hardware such as the fan speed, internal

temperature, and voltage.

10 Using the Baseboard Management Controller

www.dell.com | support.dell.com

Fan Probes Information

Table 1-7 shows the icons for the fan probes.

View the status and readings of the fan probes. There might be one or more fans, numbered [1

through

], measured in revolutions per minute (RPM).

Temperature Probes

Table 1-9 shows the icons for the temperature probes.

Table 1-7. Fan Probe Status Icons

Icon Description

Warning alert issued

Failure alert issued

Table 1-8. Fan Probe Status Icons

Item Description

Status See Table 1-7.

Probe Name Name of the sensor.

Reading The number of revolutions per minute (RPM).

Warning Threshold Minimum and maximum threshold, measured in RPM, at which a

warning alert is issued.

Failure Threshold Minimum and maximum threshold, measured in RPM, at which a

failure alert is issued.

Table 1-9. Temperature Probe Status Icons

Icon Description

Warning alert issued

Otros manuales para PowerEdge C1100

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de Dell

Dell

Dell PowerEdge 1800 Manual

Dell

Dell POWEREDGE R710 Manual técnico

Dell

Dell PowerEdge T105 Systems Manual de usuario

Dell

Dell Wyse 3030 Manual de usuario

Dell

Dell EMC Core XC750 Manual

Dell

Dell PowerEdge T310 Manual de usuario

Dell

Dell PowerEdge R210 Manual técnico

Dell

Dell PowerEdge R420 Guía de inicio rápido

Dell

Dell PowerEdge 1750 Manual de usuario

Dell

Dell PowerEdge 4200 Series Manual de usuario

Dell

Dell PowerEdge 2300 Manual de usuario

Dell

Dell 6100 Guía

Dell

Dell POWEREDGE SC440 Manual de usuario

Dell

Dell KGR3H Manual

Dell

Dell PowerEdge R715 Manual de usuario

Dell

Dell EMC PowerEdge T440 Manual

Dell

Dell PowerEdge 2800 Manual de usuario

Dell

Dell DX6000G Manual de usuario

Dell

Dell PowerEdge R610 Manual de usuario

Dell

Dell PowerEdge 6400 Manual de usuario

Dell

Dell PowerVault 735N Manual

Dell

Dell Wyse 5040 AIO Manual de usuario

Dell

Dell PowerEdge SC430 Manual de usuario

Dell

Dell PowerEdge 2500 Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario

Planet

Planet NAS-7410 Manual de usuario

Lenovo

Lenovo ThinkSystem SR635 V3 Manual de usuario

Fujitsu

Fujitsu PRIMERGY BX900 Manual de usuario

Asus

Asus RS700DA-E6 PS4 Manual de usuario