Dell 2200MP Manual de usuario

DELL 2200MP PROJECTOR USER GUIDE

SAFETY INSTRUCTIONS FOR DELL 2200MP PROJECTOR

1. Be careful in handling the unit - the surface beneath the projector might be hot with use.

2. Do not touch the bulb or the lamp glass at any time. The bulb may explode due to improper

handling, including the touching of the bulb or the lamp glass.

3. Remove lens cap before turning on projector. Failure to do so may cause the lens cap to reach

high temperatures.

4. To avoid damaging the projector and lamp, allow the cooling fan to run for 2 minutes before

turning off the projector.

5. Do not block the ventilation slots and openings on the projector.

6. Do not look into the lens while the projector is on; the bright light may hurt your eyes.

GETTING TO KNOW THE DELL 2200MP

1. Main Unit

1. The Control Panel

2. Zoom Tab

3. Focus Ring

4. Lens

5. Elevator Button

6. Remote Control Receiver

2. Control Panel

1. Power button

2. Four directional keys

3. Keystone adjustment

4. Temperature warning light

5. Lamp warning light

6. Resync

7. Menu

8. Keystone adjustment

9. Source

3. Connection Ports

1. VGA in (D-sub) connector

2. VGA Out (monitor loop-through)

3. IR receiver

4. USB connector

5. S-video connector

6. Composite video connector

7. Audio input connector

4. Remote Control

1. Light

2. Power button

3. Previous page button (page up) **

4. Four Direction buttons

5. Source button

6. Resync button

7. Keystone Correction button

8. Volume button

9. Hide button

10. 4:3/16:19 (aspect ratio) button

11. Menu button

12. Next page button (page down) – USB Needed

13. Video Mode button

SETTING UP THE PROJECTOR

1. Plug power cord into Projector and an outlet

2. Put one ends of the VGA cable into the Monitor-in

3. Put the other blue end of the VGA cable into the correct port of your laptop.

4. NOTE!! If you are using a Mac and have a digital port rather than analog, you

need a converter that will connect from your digital port to the VGA cable. (Included in projector

case)

5. Put the small end of the USB cable in its port on the projector

6. Plug the USB end of the USB cable into your computer

7. NOTE!! The projector can hook up to many sources using different cables. For a laptop, the

USB and VGA cables should suffice, unless you are adding audio using the projector. Refer to

the Owner’s Manual for further instructions.

8. Remove the lens cap

9. Once your computer is on and ready, push the Function-F8 key

10. Turn the projector on by pressing the Power button1

11. NOTE!! If the projector is plugged in and the power is off, the power button may blink green-

this is fine, it is just recognizing the power source

If your image is blurry, try twisting the

focus ring

Y/AC/Staff/Documentation/ProjectorGuideShort 11/05 cc 2

USING THE PROJECTOR

1. Control Panel

a. Source: Press to step through Analog, RGB, Composite,

Component-I, S-video, and Analog YpbPr sources when

multiple sources are connected to the projector.

b. Resync: Press to synchronize the projector to the input

source. Resync will not operate if the On-Screen Display is

displayed.

c. Menu: Press to activate the OSD (On-screen display). Use the directional keys

and the Menu button to navigate through the OSD.

d. Four Directional keys: The four directional keys can be used to toggle through the

tabs in the OSD.

e. Keystone: Press either of the buttons to adjust image distortion caused by tilting

the projector.

2. Remote Control

a. Power: See installing the projector, step 1 and 8, as well as Powering off you

projector (later in this section)

b. Press the Source button to step through Analog, RGB, Composite, Component-I, S-

video, and Analog YpbPr sources when multiple sources are connected to the

projector.

c. Resync: Press to synchronize the projector to the input source. Resync will not

operate if the On-Screen Display is displayed.

d. Directional keys: Use the up and down arrows to select OSD (On screen display)

items, use “left” and “right” button to make adjustments.

e. Hide: Press the Hide button to hide the image, press again to resume display of the

image. (Video mute).

f. Video Mode: The Dell 2200MP Microprojector has preset configurations that are

optimized for displaying data (PC Graphics) or video (movies, games, etc.). Press

Video Mode button to toggle between PC mode, Movie mode, sRGB, or User mode

(for user to setup and save preferred settings). Pressing the Video Mode button

once will show the current display mode. Pressing the Video Mode button again will

switch between modes.

g. Previous Page: Press the Previous Page button to page up. (USB must be

connected for this feature)

Y/AC/Staff/Documentation/ProjectorGuideShort 11/05 cc 3

h. Next Page: Press the Next Page button to page down. (USB must be connected for

this feature)

i. Menu: Press the Menu button to activate the OSD. Use the directional keys and

Menu button to navigate through the OSD.

j. Volume up/down: Press the up button to increase the volume, press the down

button to reduce the volume.

k. 4:3/16:9: Press the 4:3/16:9 to switch the image aspect ratio from 4:3 to 16:9. (The

most popular aspect ratio is 4:3 (4 by 3). Early television and computer video

formats are in 4:3 aspect ratio, which means that the width of the image is 4/3 times

the height.

l. Keystone: Adjusts image distortion caused by tilting the projector. ( ±16 degrees)

3. On Screen Display

a. The projector has a multi-language On-Screen Display (OSD) that can only be

displayed when an input source is present.

b. The OSD allows you to make image adjustments and change a variety of settings. If

the source is a computer, the OSD allows changes to the Computer Image tab.

When using a video source, the OSD allows changes to the Video Image tab. The

projector automatically detects the source.

c. When the OSD is on the screen, press up or down to navigate through the OSD

tabs. Example: All Images--> Computer Image--> Audio--> Management-->

Language--> Factory Reset. To make a selection in a tab, press on

keypad or "Menu" on remote controller.

d. Press or to make a selection and adjust the settings by pressing or

on keypad or Left and Right button on the remote controller. When an item is

selected, the color of the item will change to dark gray.

e. To exit the OSD, go to "Exit" tab and press button on keypad or "Menu" on

remote controller.

Y/AC/Staff/Documentation/ProjectorGuideShort 11/05 cc 4

f. Brightness: Adjusts the brightness of the image

i. Press to darken the image.

ii. Press to lighten the image.

g. Contrast: Controls the degree of difference between the lightest and darkest parts of

the picture. Adjusting the contrast changes the amount of black and white in the

image.

i. Press to decrease the contrast

ii. Press to increase the contrast.

h. Keystone: Adjusts image distortion

cause by tilting the projector.

i. Aspect Ratio: Select this function to fit 16:9U,

1:1, 16:9, and 4:3 aspect ratios. In order to use

the 1:1 aspect ratio, the input must be a computer signal (through VGA cable) of

resolution less than SVGA (800 x 600), component 576p/ 480i / 480p, S-Video, or

Video (composite). If the input signal is a computer signal greater than SVGA or

component 1080i / 720p, only 16:9, 16:9U or 4:3 aspect ratio will be available.

When an icon is selected, the color of the icon will change to dark blue.

i. 16:9U The input source will be displayed in wide screen mode (16:9) without

scaling. Some pixels will be truncated accordingly.

ii. 1:1 The input source will be displayed without scaling.

iii. 16:9 The input source will be displayed in wide screen mode (16:9) without

scaling. The source will be scaled to fit the width of the screen.

iv. 4:3 The input source will be scaled to fit the screen.

j. Video Mode: Select this function to optimize the

display image for home use (Movie Mode),

conference use (PC Mode), standard color use (sRGB), or as user preferable

settings (User Mode). When an icon is selected, the color of the icon will change to

dark blue. The default setting is PC Mode. Adjusting the settings of White Intensity

or Degamma tab will select User Mode automatically.

4. Management Menu

Y/AC/Staff/Documentation/ProjectorGuideShort 11/05 cc 5

a. Menu Location: Select the location of the on-

screen display on the screen.

b. Projection Mode:

i. Front Projection-Desktop: The default setting.

ii. Rear Projection-Desktop: The projector reverses the image so you can

project from behind a translucent screen.

iii. Front Projection-Ceiling Mount: The projector turns the image upside down

for ceiling-mounted projection.

iv. Rear Projection-Ceiling Mount: The projector simultaneously reverses and

turns the image upside down. You can project from behind a translucent screen

with a ceiling-mounted projection.

c. To adjust the size of the projected image, move the projector closer or further away

from the surface on which you are projecting.

For any further settings changes, please refer to the Owners’ Manual included

with the projector.

TROUBLESHOOTING

1. No image appears on the screen

a. Ensure that the lens cap is removed and the projector is turned on

b. Ensure the external graphics port is enabled. If you are using a Dell portable

computer, press the F8 key. For other computers, consult your owner’s manual.

c. Ensure that all the cables are securely connected as described in the installation

section.

d. Ensure that the pins of the connectors are not bent or broken

2. Partial scrolling, or incorrectly displayed image

a. Press the Resync button on the remote control or the control panel

b. If you are using a Dell portable computer: (for other computers consult your owner’s

manual)

i. Set the resolution of the computer to SVGA (800 x 600):

(1) Right click on the unused portion of your Windows desktop ÆProperties Æ

Settings tab.

(2) Verify the “Screen area” slide bar is set to 800 x 600 pixels.

ii. Press Function-F8

Y/AC/Staff/Documentation/ProjectorGuideShort 11/05 cc 6

c. If you experience difficulty in changing the resolutions or your monitor freezes,

restart all the equipment and the projector.

3. The screen does not display your presentation

a. If you are using a portable computer, press Function-F8

4. Image is unstable or flickering

a. Adjust the tracking in the OSD “Computer Image” tab.

5. Image color is not correct

a. If your graphic card output signal is “sync on Green”, and you would like to display

VGA at 60Hz signal, please go into “OSD ÆManagement ÆSignal Type” and

select “RGB”.

6. Image is out of focus

a. Adjust the focus ring on the projector lens

b. Ensure that the projection screen is within the required distance from the projector

(3.9 ft [1.2m] to 39.4 ft [12m]).

7. The image is stretched when displaying 16:9 DVD

a. The projector automatically detects 16:9 DVD and adjusts the aspect ratio to full

screen with a 4:3 (letter-box) default setting. If the image is still stretched, adjust the

aspect ratio as follows:

i. If you are playing a 16:9 DVD, select 4:3 aspect ratio type on your DVD player if

capable.

ii. If you cannot select 4:3 aspect ratio on type on your DVD player, select 4:3

aspect ratio in the “All Images” menu within the OSD function

8. Image is reversed

a. Select Management from the OSD and adjust the projection mode

9. Lamp is burned out or makes a popping sound

a. Please return the projector to IT immediately so that we can take care of the lamp

change.

10.Noise made when turning projector upside down

a. This is normal. This feature inside the projector allows for proper cooling in ceiling

mount applications.

For any further information or problems please consult the owner’s

manual or call Scripps AV at x73193.

Y/AC/Staff/Documentation/ProjectorGuideShort 11/05 cc 7

Otros manuales para 2200MP

Tabla de contenidos

Otros manuales de Proyector de Dell

Dell

Dell 3400MP - XGA DLP Projector Manual de usuario

Dell

Dell PowerEdge RAID Controller S300 Manual de usuario

Dell

Dell 4100MP Instrucciones de instalación

Dell

Dell Mobile M115HD Manual de usuario

Dell

Dell 2400MP - XGA DLP Projector Manual de usuario

Dell

Dell S300WI Manual de usuario

Dell

Dell 1800MP Manual de usuario

Dell

Dell S510 Manual de usuario

Dell

Dell 5100MP - SXGA+ DLP Projector Manual de usuario

Dell

Dell 3200MP - XGA DLP Projector Instrucciones de instalación

Dell

Dell 2100MP Manual de usuario

Dell

Dell S520 Manual de usuario

Dell

Dell 3400MP - XGA DLP Projector Manual de usuario

Dell

Dell 7700HD Manual de usuario

Dell

Dell 7609WU - WUXGA DLP Projector Manual de usuario

Dell

Dell S510 Manual de usuario

Dell

Dell 2400MP - XGA DLP Projector Manual de usuario

Dell

Dell XXX Manual de instalación y operación

Dell

Dell M110 Manual de usuario

Dell

Dell 2200MP Manual de usuario

Dell

Dell Vostro 1220 Manual de usuario

Dell

Dell Mobile M900HD Manual de usuario

Dell

Dell S320 Manual de usuario

Dell

Dell S560T Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario