Dell EMC Networking N Series Manual de usuario

Dell EMC Networking N-Series

N2200 Switches

Getting Started Guide

Version 6.6.1

Regulatory Model: E41W

Notes and Cautions

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if

instructions are not followed.

____________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

This product is protected by U.S. and international copyright and intellectual property laws. Dell

EMC™ and the Dell EMC logo are trademarks of Dell EMC Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective

companies.

Marketing Models: N2224X-ON, N2224PX-ON, N2248X-ON, N2248PX-ON

Regulatory Model: E41W

2019 - 11 Rev. A00

Contents 1

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3

2 N2200 Series Overview . . . . . . . . . . . . . . . 3

3 N2200 Series Hardware Overview. . . . . . . 4

Dell EMC Networking N2200-ON Series Switch Hardware 4

4 N2200 Installation . . . . . . . . . . . . . . . . . . 13

Site Preparation . . . . . . . . . . . . . . . . . . . . . 13

Unpacking the N2200 Switch . . . . . . . . . . . . . . 14

Rack Mounting a N2200 Switch . . . . . . . . . . . . . 14

Stacking Multiple N2200 Switches . . . . . . . . . . . 16

5 Starting and Configuring the N2200 Switch 18

Connecting a N2200 Switch to a Terminal . . . . . . . 19

Connecting a N2200 Switch to a Power Source . . . . 20

Booting the N2200 Switch . . . . . . . . . . . . . . . . 21

Performing the N2200 Initial Configuration . . . . . . . 21

2Contents

6 Specifications . . . . . . . . . . . . . . . . . . . . . 28

Chassis Physical Design. . . . . . . . . . . . . . . . . 28

7 Dell EMC Support. . . . . . . . . . . . . . . . . . . 32

Introduction

This document provides basic information about the Dell®EMC™

Networking N2200 Series switches, including how to install a switch and

perform the initial configuration. For information about how to configure and

monitor switch features, see the User’s Configuration Guide, which is

available on the Dell Support website at

dell.com/support/manuals

, for the

latest updates on documentation and firmware.

This document contains the following sections:

• N2200 Series Overview

• N2200 Series Hardware Overview

• N2200 Installation

• Starting and Configuring the N2200 Switch

NOTE: Switch administrators are strongly advised to maintain Dell EMC

Networking switches on the latest version of the Dell EMC Networking Operating

System (DNOS). Dell EMC Networking continually improves the features and

functions of DNOS based on feedback from you, the customer. For critical

infrastructure, prestaging of the new release into a noncritical portion of the

network is recommended to verify network configuration and operation with the

new DNOS version.

N2200 Series Overview

The Dell EMC Networking N2200-ON switches are stackable Layer 2/3 1

Gigabit stackable Ethernet switches and include the following models:

• Dell EMC Networking N2200X-ON

• Dell EMC Networking N2224PX-ON

• Dell EMC Networking N2224X-ON

• Dell EMC Networking N2248PX-ON

• Dell EMC Networking N2248X-ON

N2200 Series Hardware Overview

Dell EMC Networking N2200-ON Series Switch

Hardware

This section contains information about device characteristics and modular

hardware configurations for the Dell EMC Networking N2200 Series

switches.

N2200-ON Series Front Panel

The Dell EMC Networking N2224X-ON/N2224PX-ON/N2248X-

ON/N2248PX-ON switch front panels include the following features:

• 24 or 48 RJ-45 10/100/1000/2500BASE-T ports

• Four SFP28 10G/25GBASE-X ports

• Two QSFP 40G stacking ports

• RJ-45 and Type-B micro USB 3.0 console ports

• Reset button

• Port and system LEDs

• Stack Master LED and Stack Number Display

• Type-A USB 3.0 port for storage

• Out-of-band Ethernet interface

The following images show a representative front panel of the Dell EMC

Networking switch.

Figure 1-1. Dell EMC Networking N2248PX-ON Switch (Front Panel)

N2200-ON Series Rear Panel

The Dell EMC Networking N2200-ON Series back panel has two 40G QSFP

stacking ports in the rear. It also has two slots for power supplies, and two

(N2224X-ON/N2224PX-ON) or three (N2248X-ON/N2248PX-ON) hot-swap

fan trays.

Figure 1-2. Dell EMC Networking N2248PX Switch (Rear Panel)

N2200X-ON Series Switch Ports

The Dell EMC Networking N2200X-ON Series front panel provides 24 or 48

10/100/1000/2500BASE-T Ethernet RJ-45 ports that support auto-negotiation

for speed, flow control, and duplex. Dell EMC Networking N2200X-ON

Series switch front panel 2.5G ports operate in full-duplex at all speeds or

half-duplex at 10/100 Mbps speeds. The Dell EMC Networking N2200X-ON

Series switch models support four 10G/25G SFP28 ports and two 40G QSFP

stacking ports. Dell-qualified transceivers are sold separately.

The front-panel switch ports have the following characteristics:

• The switch automatically detects the difference between crossed and

straight-through cables on RJ-45 ports and automatically chooses the MDI

or MDIX configuration to match the other end.

• The 10/100/1000/2500BASE-T Ethernet RJ-45 ports support full-duplex

mode 10/100/1000/2500 Mbps speeds or half-duplex 10/100 Mbps speeds

on standard Category 5 UTP cable. 2500BASE-T operation requires the

use of auto-negotiation.

• SFP28 ports support Dell-qualified transceivers utilizing 25GBASE-SR,

25GBASE-LR, 25GBASE-CR, 25GBASE-CR-S or 25GBASE-ER

technologies. SFP28 ports support SFP+ fiber transceivers and SFP+

copper twin-ax or DAC technology operating at 10G speeds in full-duplex

mode. All four SFP28 ports must be configured to operate at the same

speed. 25GBASE-CR and 10G-BASE-CR modes (copper twin-ax or DAC

cables) require the use of auto-negotiation.

• The default behavior is to log a message and generate an SNMP trap on

insertion or removal of a transceiver that is not qualified by Dell. The

message and trap can be suppressed by using the service unsupported-

transceiver command.

On the N2224X-ON/N2224PX-ON switches, ports 1-12 may be configured to

support 10M/100M half-duplex.

On the N2248X-ON switches, ports 5-36 may be configured to support

10M/100M half-duplex.

N2200-ON SFP28 ports may be configured to operate using SFP+

transceivers using the speed 10000 command for fiber media or the speed

auto 10000 command for copper media. All four SFP28 ports must be

configured to operate at the same speed. A mix of SFP+ and SFP28

transceivers or speeds is not supported. The switch UI does not enforce this

restriction.

N2200-ON Series Console Port

The console port provides serial communication capabilities, which allows

communication using RS-232 protocol. The serial port provides a direct

connection to the switch and allows access to the CLI from a console

terminal connected to the port through the provided serial cable (with RJ-45

YOST to female DB-9 connectors). The console port is separately

configurable and can be run as an asynchronous link from 1200 baud to

115,200 baud. The Dell CLI only supports changing the speed. The defaults

are 115,200 baud rate, 8 data bits, no parity, 1 stop bit, no flow control.

Figure 1-3. Dell EMC Networking N2248 Console Port

A separate USB micro type B port is also available for console access to the

CPU CLI. RS-232 emulation over USB is supported on this port. A driver may

need to be installed to support the RS-232 emulation. Only one of the

console ports may be used at a time.

N2200-ON Series USB Port

The Type-A, female USB port supports a USB 3.0-compliant flash memory

drive. The Dell EMC Networking N-Series switch can read or write to a flash

drive with a single partition formatted as FAT-32. Use a USB flash drive to

copy switch configuration files and images between the USB flash drive and

the switch. The USB flash drive may be used to move and copy configuration

files and images to other switches in the network. The system does not

support the deletion of files on USB flash drives. The USB port does not

support any other type of USB device.

N2200-ON Series Reset Button

The reset button is accessed through the pinhole and enables performing a

hard or soft reset of the switch. To reset the switch, insert an unbent paper

clip or similar tool into the pinhole for four seconds. When the switch

completes the boot process after the reset, it resumes operation with the most

recently saved configuration. Any changes made to the running configuration

that were not saved to the startup configuration prior to the reset are lost.

To clear the configuration and reset the switch, press the reset button for at

least eight seconds. The saved configuration is cleared and the switch reboots.

The switch then starts the autoconfiguration process.

N2200-ON Series Port and System LEDs

The front panel contains light emitting diodes (LEDs) that indicate the

status of system temperature, port links, power supplies, fans, stacking, and

the overall system status. A locator beacon capability is also present on the

system LEDs. See

N2200-ON Series LED Definitions

for more information.

N2200-ON Series Stack Master LED and Stack Number Display

When a switch within a stack is the master unit, the stack master LED is solid

green. If the stack master LED is off, the stack member is not the master unit.

The stack number LCD displays the unit number for the stack member. If a

switch is not part of a stack (in other words, it is a stack of one switch), the

stack master LED is illuminated, and the unit number is displayed.

N2200-ON Series Power Supplies

The Dell EMC Networking N2224X-ON/N2248X-ON switches have a field-

replaceable 550W power supply (DS-550 AC). An additional field-replaceable

power supply may be added to support redundancy.

The Dell EMC Networking N2224PX-ON switches have a field-replaceable

1050-watt power supply (DPS-1050 AC) feeding up to 16x30W PoE and

2x60W devices at full power (712W). The Dell EMC Networking N2248PX-

ON switches have an internal 1050W power supply (DPS-1050 AC) feeding

up to 16x30W PoE devices and 1Xx60W at full power (624W).

In both PoE models, additional field replaceable 1050W, 1300W, or 1600W

power supplies are available to support redundancy or to supply full front

panel demand.

Table 1-1 shows power budget data.

Table 1-1. Dell EMC Networking N2200PX-ON Series PoE Power Budget Limit

One PSU Two PSUs (2x1050W)

Model Name PoE Power

Budget

Power

Turn-on Limitation

PoE Power

Budget

Power

Turn-on Limitation

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Dell EMC

Dell EMC

Dell EMC S5048F-ON Manual de usuario

Dell EMC

Dell EMC PowerSwitch Z9332F-ON Manual de usuario

Dell EMC

Dell EMC S4112F-ON Manual de usuario

Dell EMC

Dell EMC VEP4600 Guía del usuario

Dell EMC

Dell EMC PowerSwitch N1100-ON Series Manual de usuario

Dell EMC

Dell EMC S5232F-ON Manual de usuario

Dell EMC

Dell EMC S4148U-ON Guía rápida

Dell EMC

Dell EMC PowerSwitch N3200-ON Series Manual de usuario

Dell EMC

Dell EMC Z9264F-ON Manual de usuario

Dell EMC

Dell EMC N1108T-ON Manual de usuario

Dell EMC

Dell EMC S4048T-ON Manual de usuario

Dell EMC

Dell EMC SD-WAN Edge 3000 Series Manual de usuario

Dell EMC

Dell EMC PowerSwitch S4810-ON Manual de usuario

Dell EMC

Dell EMC S5200F-ON Series Manual de usuario

Dell EMC

Dell EMC PowerSwitch Z9332F-ON Manual de usuario

Dell EMC

Dell EMC PowerSwitch S4100-ON Series Manual de usuario

Dell EMC

Dell EMC Z9264F-ON Manual de usuario

Dell EMC

Dell EMC N20 Series Manual de usuario

Dell EMC

Dell EMC PowerSwitch N3200-ON Series Manual de usuario

Dell EMC

Dell EMC PowerSwitch N2200-ON Series Manual de usuario

Dell EMC

Dell EMC SD-WAN Edge 600 Series Manual de usuario

Dell EMC

Dell EMC N3024ET-ON Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario