Deif BRW-2 Manual de usuario

Note about accuracy

As this is a special version of the BRW-2 with additional circuits to simulate BRW-1

operation, the standard specified accuracy (Class 0.5) is not met.

BRW-2 Replacement is specified to: Class 1.0.

Future replacement

For future replacement, it is not necessary to replace the entire BRW-2 indicator. It may

be sufficient to change the XL192 indicator part (the top part of the product). This will

facilitate reinstallation.

Please note that when replacing the XL192 indicator built into the BRW-2, the measuring

range is either 0 to 1 mA or ±1 mA. Please refer to the type label on the XL192 indicator.



Q

UICK GUIDE

BRW-2 Replacement for BRW-1



Refer to www.deif.com for complete documentation

Document no.: 4189350057A









Mounting

This product is only relevant for replacement of existing BRW-1 products.

The BRW-2 is protected from ESD (static electricity), so no special protection from ESD

is needed during mounting.



Warranty label

If this label is removed or broken, the warranty will be lost.

Power-up the first time

When the indicator is without power, the pointer position is random.

The indicator is equipped with an amber LED lamp in the lower corner of the scale area.

After power-up, the LED will flash once or twice and is then turned off.

When power is applied, the pointer will be out of control for a few seconds. This is normal

operation.

Wiring

Dismount the potentiometer plate (use a standard 4 mm Allen key), and the connection

terminals will be visible. Be careful not to damage the gasket when the potentiometer

plate is dismounted from the housing.

Standard voltage for supply and illumination is 24 V

dc

. Connect the illumination supply 24

V

dc

to terminals pos. 5 and 6. For personal protection, the terminal marked “EARTH”

must be connected to the ship’s hull.

The potentiometer marked “MAX. ADJ”, positioned between the two connectors, can be

used for small adjustments of the deflection of the pointer to fit the scaling of the indicator

to the existing installation.



Otros manuales para BRW-2

2

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Instrumento de medición de Deif

Deif

Deif BRW-2 Manual de usuario

Deif

Deif XL Manual de usuario

Deif

Deif MIB 7000 Manual de usuario

Deif

Deif MIC-2 MKII Instrucciones de funcionamiento y mantenimiento

Deif

Deif Insight Manual de usuario

Deif

Deif XDi Series Manual de usuario

Deif

Deif TRI-2 Manual de usuario

Deif

Deif ADL-111Q96/xxVDC Series Instrucciones de instalación

Deif

Deif WSI Manual de usuario

Deif

Deif MIC-2 MKII Manual de usuario

Deif

Deif DLQA96 Manual de usuario

Deif

Deif MIQ96-2 Manual de usuario

Deif

Deif BRW-2 Manual de usuario

Deif

Deif MIB 8000 Manual de usuario

Deif

Deif AGC 150 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario