Dedrone RF-300 Manual de usuario

IM-Inst-RF300en v12.0 ENGLISH

INSTALLATIONS

Manual

RF-300

Dedrone

2v12.0 IM-Inst-RF300en

Legal Provisions

The information contained in these documents is the property of Dedrone GmbH. Any publication,

whether in whole or in part, requires prior written approval by Dedrone GmbH. Internal reproduc-

tion used solely for the purpose of product evaluation or other proper use is allowed and does not

require prior approval.

The declaration of conformity is available on request at support@dedrone.com.

This manual is the intellectual property of Dedrone GmbH and is protected by copyright. All rights

reserved.

Dedrone GmbH

Miramstraße 87

34123 Kassel

Germany

Fon +49 561 861799-0

Fax +49 561 861799-111

Email info@dedrone.com

Dedrone Holding, Inc.

1099 Folsom St

San Francisco, CA 97103

USA

Fon +1 4145 913-6116

Email info@dedrone.com

IM-Inst-RF300en v12.0

Dedrone

Content

1 Safety ..............................................................................................................................................4

1.1 Symbols.................................................................................................................................................................4

1.2 Intended Use ........................................................................................................................................................4

1.3 Safety Information.............................................................................................................................................. 5

2 The RF-300..................................................................................................................................... 6

3 Unpacking....................................................................................................................................... 6

4 Scope of Delivery .......................................................................................................................... 7

5 Select the Mounting Place .......................................................................................................... 7

5.1 Mounting Location .............................................................................................................................................. 7

5.1.1 Detection Conditions................................................................................................................................. 7

5.1.2 Direction Finding and Localization Conditions.....................................................................................8

5.2 Overvoltage Protection ...................................................................................................................................10

5.3 Mounting Surface...............................................................................................................................................11

5.4 Mounting Orientation........................................................................................................................................11

5.5 Mounting Device.................................................................................................................................................11

6 Installation................................................................................................................................... 12

6.1 Power Supply ..................................................................................................................................................... 12

6.2 Required Tools.................................................................................................................................................... 12

6.3 Cable Requirements.......................................................................................................................................... 12

6.4 Cable Preparation.............................................................................................................................................. 12

6.5 Installation with Pole Mount .......................................................................................................................... 13

7 Integrate RF-300 in your DroneTracker .................................................................................. 15

7.1 Integrate the RF-300 on premises installations.......................................................................................... 15

7.2 Integrate the RF-300 via Dedrone Cloud...................................................................................................... 17

8 Cleaning........................................................................................................................................ 18

9 Decommissioning ....................................................................................................................... 18

9.1 Shut down the RF-300 ..................................................................................................................................... 18

9.2 Dismantling ........................................................................................................................................................ 18

9.3 Disposal ............................................................................................................................................................... 18

10 Technical Data ............................................................................................................................. 19

Safety

Dedrone

4v12.0 IM-Inst-RF300en

1 Safety

1.1 Symbols

Symbol Explanation

Indicates a situation which, if not avoided, can result in property damage

Information that is important for a specific goal, but is not safety-rele-

vant

Indicates a requirement for meeting a specific goal

Desired result

A problem that might occur

Action to resolve a problem

1.2 Intended Use

The RF-300 is a passive, network-attached sensor for the detection and direction finding of radio

frequencies (RF) and Wi-Fi signals. In combination with two or more RF-300 it is able to determine

the position of a drone by the RF signals. The RF sensor detects targeted radio signals, identifies

their direction and sends the data, along with an alert to the DroneTracker System.

The RF-300 is intended for civil commercial and private use in conjunction with a DroneTracker

System.

The RF-300 is suitable for outdoor use.

Use this product only in accordance with the information provided in the enclosed documentation

and with the locally applicable legal standards and directives. Any other application may cause per-

sonal injury or property damage.

Any use of the product other than that described in the intended use section does not qualify as

appropriate. The enclosed documentation is an integral part of this product. Keep the documentati-

on in a convenient place for future reference and observe all instructions contained therein.

The type label must remain permanently attached to the product.

Compliance Information Statement FCC and IC

The RF-Sensor RF-300 complies with Industry Canada licence-exempt RSS standard(s) and complies

with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

IM-Inst-RF300en v12.0

Dedrone

Safety

Note: This equipment has been tested and found to comply with the limits for a Class A digital de-

vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecti-

on against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

Modifications: Any modifications made to this device that are not approved by Dedrone GmbH may

void the authority granted to the user by the FCC to operate this equipment.

Caution!

To prevent permanent exposure, the device should be installed and operated with a

minimum distance of 20 cm (7.87 in) between the device and your body.

1.3 Safety Information

Read, follow and retain all of the following safety instructions. Heed all warnings on the unit and in

the operating instructions before operation.

Warning! Setup should be carried out by trained personnel only, in accordance with the

national electric code, ANSI/NSPA, and all local country codes.

Do not attempt to service this device yourself. Refer all servicing to qualified service per-

sonnel. This device has no user-serviceable internal parts.

Whenever any damage to the device has occurred, unplug the devices from the power

source by disconnecting the patch cable and refer servicing to qualified service personnel.

Such damages can be:

•the patch cable is damaged

•an object has fallen on the device

•the device has been dropped, or its enclosure has been damaged

•the device does not operate normally when the user follows the operating instruc-

tions correctly

Adjust only those controls specified in the operating instructions. Improper adjustment of

other controls may cause damage to the unit.

Despite careful construction, electrical devices can cause fires. Do not mount the RF-300

in areas containing highly flammable materials or gases. Do not mount the RF-300 in a

potentially explosive atmosphere.

Do not install product near any heat sources such as radiators, heaters, exhaust air sys-

tems or other equipment (including amplifiers) that produce heat.

The RF-300

Dedrone

6v12.0 IM-Inst-RF300en

Parts of the RF-300

AAntenna cover EPower button

BKnurled nut FNetwork socket

CRF Mounting Plate GWi-Fi-antenna

DKnurled head screw with sealing washer

2 The RF-300

The RF-300 is a passive, network-attached sensor for the detection and direction finding of radio

frequencies (RF) and Wi-Fi signals. In combination with two or more RF-300 it is able to determine

the position of a drone by the RF signals. The RF sensor detects targeted radio signals, identifies

their direction and sends the data, along with an alert to the DroneTracker System.

It scans a wide frequency band for radio frequencies and classifies them. The data is recorded and

available on the user interface DroneTracker UI.

3 Unpacking

This equipment should be unpacked and handled with care. Check the exterior of the packaging for

visible damage. If an item appears to have been damaged in shipment, notify the shipper immedia-

tely.

IM-Inst-RF300en v12.0

Dedrone

Scope of Delivery

1 x RF-300

1 x Wi-Fi antenna

1 x RF Mounting Plate (preassembled)

2 x Knurled head screw with sealing washer (preassembled)

2 x Knurled nut (preassembled)

1 x Pole Mount

2 x Strap

1 x Bag with 4x screws Torx M5, 8x flat washer, 4x nuts

1 x Bag with 1x environmentally sealed Ethernet crimp connector, 1x RJ45 plug

1 x Installation manual

1 x Safety information

1 x Product registration document (this information is only needed for a cloud based sensor operation and is

provided by an enclosed document or online by the Dedrone Service)

The original packing carton is the safest container in which to transport the unit and must be used if

returning the unit for service. Save it for possible future use.

4 Scope of Delivery

Verify that all the parts listed in the scope of delivery are included. If any items are missing, notify

your Dedrone Partner.

Do not use this product if any component appears to be damaged. Please contact Dedrone in the

event of damaged goods.

5 Select the Mounting Place

5.1 Mounting Location

The position of the RF-300 has strong impact to the detection and direction finding range and ac-

curancy. The RF-300 is intended for pole mounting. Make sure that a suitable pole is available (dia-

meter between 1.2 in to 3.5 in (40 mm to 90 mm)) and the Antenna Cover extend beyond the pole.

The detection is the precondition for the direction finding.

5.1.1 Detection Conditions

For ideal results the location should fulfill the following conditions:

Clear view over the area

Exposed, elevated position (minimum 10 ft (3 m))

Select the Mounting Place

Dedrone

8v12.0 IM-Inst-RF300en

Note the properties of each RF-300. This is needed for the correct configuration and

for service.

We recommend the table below. The following information is important:

•Serial Number

•GPS position (longitude and latitude)

•Horizontal angle

Serial number

(see prouct plate)

GPS position

(in degree, e.g. 52.516295, 13.377653)

Horizontal angle (azimuth)

in degrees (0 = north, 90 = east, 180 = south,

270 = west)

longitude:

latitude:

longitude:

latitude:

longitude:

latitude:

5.1.2 Direction Finding and Localization Conditions

For accurate localization results, follow the guidance below in addition to the Detection Conditions

(see 5.1.1 Detection Conditions, page 7).

The position is determined by the intersection of at least two bearings. Therefore minimum two

RF-300 sensors are required for localization, but we recommend at least three RF-300 sensors as

this significantly reduces localization errors.

For best localization results, all RF-300 sensor should be installed at the same height.

Do not install the device nearby the following objects:

•Metal surfaces or vaporized glass

Disturbs the detection and prevents the localization

•Walls

These share the detection area and prevent classification of signals behind the wall

•Base station and other strong signale sources

The detected signals are getting interfered

•Any excessive heat sources

•Any overhead power lines, power circuits, or electrical lights

electrical discharge can damage the device.

Select a secure installation location and mounting position for the device. Ideally, this is a location

where the device cannot be interfered with, either intentionally or accidentally.

IM-Inst-RF300en v12.0

Dedrone

Select the Mounting Place

To localize a drone an intersection

of the bearings from at least two

sensors is needed.



Localization is not possible in

the case where two RF-300s are

aligned.

This is the blind area of two sensors.



Both RF-300s detects a direction

in alignment to the left. The over-

lapping area covers the complete

bearing of the other RF-300. The

position can’t be determind.



Both RF-300s detect a direction in

alignment to the right. The over-

lapping area covers the complete

bearing of the other RF-300. The

position can’t be determind.

Both RF-300s detect a direction

against each other. No exact positi-

on can be determined.

With three RF-300s there is no blind

area. The third RF-300s can always

varify the area of intersection.

Position of the sensors to each other

Select the Mounting Place

Dedrone

10 v12.0 IM-Inst-RF300en

Distances between the RF-300s

The distance between the RF-300 usually should be 330 ft to 1,300 ft (100 m to 400 m).

330 ft to 1,300 ft

(100 m to 400 m)

330 ft to 1,300 ft

(100 m to 400 m)

Distance between the RF-300s

Lightning Protection Installation with RF-300s

For the best result, Dedrone strongly recommends a distance of 1,000 ft to 1,300 ft (300 m to

400 m).

Choose the postion depending on your monitoring focus. Increase the distance between the

sensors to increase the accuracy at further distances.

Localization accuracy increases as the drone gets closer to the sensors.

5.2 Overvoltage Protection

For safe mounting in an exposed position overvoltage protection must be observed.

Ensure that the pole is connected to the lightning conductor of the building. The RF-300 itself

must not be grounded directly. The lightning conductor must be installed at least 1.5 m above the

RF-300.

330 ft to 1,300 ft

(100 m to 400 m)

Ensure that the location has the appropriate clearance from power and lightning conductors, in

accordance with NEC725 and NEC800 (CEC Rule 16-224 and CEC Section 60).

Otros manuales para RF-300

Tabla de contenidos

Otros manuales de Accesorios de Dedrone

Dedrone

Dedrone RF-100 Manual de usuario

Dedrone

Dedrone RF-360 Manual de usuario

Dedrone

Dedrone RF-160 Manual de usuario

Dedrone

Dedrone RF-300 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario