Dedicated Micros DM/CAM/SDH36/N Manual de usuario

Vandal PTZ Speed Dome Camera

Installation Manual

DM/CAM/SDH36/N

www.dedicatedmicrosus.com

SDH36

Whilst every attempt is made to ensure these manuals are accurate and current, Dedicated Micros reserve the right to

alter or modify the specication of the machine described herein without prejudice.

Contents

Contents ............................................................2

Introduction .......................................................3

Components supplied .......................................5

Mounting Congurations ...................................6

Electrical Connections.......................................14

Control Conguration ........................................15

Troubleshooting ................................................19

Notes .................................................................21

SDH36

Introduction

Congratulations on choosing a Dedicated Micros Vandal PTZ speed dome camera.

This manual will provide all the information necessary to install the Dedicated Micros SDH36.

USA Regulatory Notice

This product is compliant with UL2044, safety of Commercial CCTV Products and UL 50.

This series of products complies with FCC Part 15 Class A.

Class A is typically used for business or industrial environments.

RF Interference warning

This is a class A product. In a domestic environment this product may cause radio frequency

interference, in which case the user may be required to take adequate measures.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Use only attachments/accessories specied by the manufacturer.

6 Use only with the cart, stand, tripod, bracket or table specied by the

manufacturer, or sold with the apparatus.

7 Unplug this apparatus during lightening storms or, when unused for long periods of

time.

8 Refer all servicing to authorized service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power supply cord or plug is

damaged.

9 WARNING. DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY

REPLACED.

REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

10 Use only a UL listed class 2 power supply with a minimum current of 1.5 amps and

the wiring as specied in the National Electrical Code ANSI/NFPA 70.

Canadian EMC statement.

This product is compliant with Class A ICES-003.

Note: This Class A product meets the requirements of the Canadian Interference causing

equipment regulations.

Cet appareil numerique de la Classe A, respect toutes les exigencies du reglement sur le materiel

brouilleur du Canada.

SDH36

CE NOTICE (EUROPEAN UNION).

Marking by the symbol CE indicates compliance of this DM product to the Electromagnetic

Compatibility Directive 89/336/EEC, and the Low Voltage Directive 73/23/EEC of the European

Union. Such marking is indicative that this system meets the following technical standards.

• EN 61000-6-3 EMC Standard Residential, Commercial and Light Industry.

• EN 61000-3-3 Limitations of voltage changes, uctuations and icker in public low-

voltage supply systems for equipment with rated current up to 16A.

• EN 61000-3-2 Limits for harmonic current emissions for equipment with rated

current up to 16A.

• EN 50130-4 Immunity requirements for components of re, intruder and social

alarm systems.

• EN 60950 Safety of IT and related equipment.

• EN 55022 Class B. Radiated Emissions Standard, suitable for Commercial or

Residential use.

• EN 60825-1 Safety standard for LED’s and Lasers.

Further details about these applicable standards can be obtained from Dedicated Micros LTD. 1200

Daresbury Park, Daresbury, Cheshire, WA44HS.

A “Declaration of Conformity” with all relevant European Union Directives has been made, is on le

and is available from the Dedicated Micros address above.

This product is marked with the CE symbol and indicates compliance with all applicable directives.

Directive 89/336/EEC.

A “Declaration of Conformity” is held at Dedicated Micros Ltd., 1200 Daresbury Park, Daresbury,

Cheshire, WA44HS.

SDH36

Components supplied

Before installing the dome, please remove the components from the packaging and verify that all

items listed below have been supplied:

1 x Dedicated Micros SDH36 Dome enclosure (with safety bond)

1 x Installation manual

1 x Operation and Programming manual

Note: Any PSU used must be a UL 2044 approved Class 2 current limited 24VAC Power Supply.

Caution:

To avoid damaging the dome, the 24VAC output from the power supply must

be left oating with respect to the electrical ground.

Note: Mounting brackets may have been ordered and delivered separately.

SDH36

Mounting Congurations

With appropriate brackets this dome enclosure can be mounted in any of the

orientations shown below. The mounting bracket is prewired for ease of installation.

Note: Mounting brackets may have been ordered and delivered separately.

1. Wall/Pendant Mount (order code DM/CAM/SDAWP/N) giving pendant or wall

mount options.

2. Corner Bracket (order code DM/CAM/SDACM/N) for mounting to corners of

buildings in conjunction with DM/CAM/SDAWP/N.

3. Tile mount (order code DM/CAM/SDACT/N) for suspended ceilings.

4. Snowdrop mount bracket (order code DM/CAM/SDASM/N) for mounting at the top

of a pole, column or roof parapet.

All mounting versions are suitable for both weatherproof (IP66 BS EN 60529/NEMA Type 4X) and

indoor units.

SDH36

Safety Bond

The safety bond is designed to prevent damage to the dome if it is dropped during installation or

maintenance. It should be connected between the mounting point on the dome and a suitable

secure position, either on the bracket or within the ceiling void. This point should be selected with

the consideration that it will receive the full force of the dome if it is dropped.

For wall, pendant & snowdrop/parapet mounted domes;

1. Clip safety bond to the mounting bracket eyelet (B) on ange of bracket to secure.

For standard ceiling mounted domes attach the supplied safety bond;

1. Attach safety bond to a suitable secure position in the ceiling void.

Note: Always support dome with bond prior to mating connector (C). Weight of dome should be

supported by bond ensuring no stress is placed on centre connector (C) at any time.

SDH36

Wall/Pendant Mounting

Your mounting kit should come with a set of detailed specic instructions. Directions here are for

quick reference only.

The Node Casting (item 2) should be used as a marking template to correctly position the required

holes.

Important: If the bracket is to be installed as a wall bracket (with the mounting arm xed at 90°),

the Node Casting needs to be mounted with the levelling faces (b) exactly horizontal and

vertical. Use a spirit or bubble level to ensure the faces are level.

Note: The Node Casting is designed with ‘punch out’ holes in the base to allow the network cable

to exit the back of the casting. If this installation technique is used, the Gland should be

sealed to prevent water ingress.

Note: Locating a dome on a corner of a building will give an increased area of surveillance. An

optional corner bracket (DM/CAM/SDACM/N) will adapt the standard wall bracket to suit this

application.

The four screws (item 3) Node Casting to the wall, using 4 x ¼”(M6) plugs.

1. Drill 4 x 9/32”(Ø7mm) dia. holes (a) at the screw positions using the Mode Casting

(item 2) as a guide. Use a spirit level on the levelling face (b) to ensure correct

orientation.

2. Insert 4 x ¼”(M6) plugs (item 1) into the holes and mount the Node Casting (item 2)

using the 4 wall xing screws (item 3) provided.

3. Connect the cable from the network to the three way and four way connector

blocks as detailed in the ‘Electrical Connections’ section of this manual.

SDH36

4. Position the Mounting Bracket (item 5) next to the Node Casting and push t the

wiring node onto the 7 way termination node.

5. Using supplied ¼”(M6) xings (item 4), fasten the Mounting Bracket to the

Node Casting.

6. Fix the dome to the end of the Mounting Bracket, refer to ‘Dome Mounting’.

Note: Bracket base casting can be orientated to position the entry hole to either side or at the top.

SDH36

Snowdrop/Roof Parapet Mounting

Your mounting kit should come with a set of detailed specic instructions. Directions here are for

quick reference only.

The Node Casting (item 7) has been designed

with 4 holes equi-spaced on 4”(108mm) Pitch

Circle Diameter (PCD).

Important: This product is likely to be installed

at high level. Ensure all local safety

regulations are adhered to during

installation. If possible, follow the

procedure until installation of the dome at

ground level, to minimise risk.

Note: The Node Casting (item 7) is designed

with ‘punch out’ holes in the base to

allow the cable to exit the back of the

casting. If this installation technique is

used, the Gland should be sealed to

prevent water ingress.

1. The Bracket Assembly (item 4)

is a heavy item and should be

supported adequately during

installation.

Pole Installation only

2. The Node Casting (item 7) is

designed with 4 holes

equi-spaced on 4”(108mm)

Pitch Circle Diameter (PCD) to

allow direct installation on the

end of the pole. Use suitable

¼”(M6) xings to fasten the Node

Casting to the pole.

Note: Dedicated Micros does not supply these

ttings, due to the variation in materials

and thickness found on site.

Parapet installation only

2. Drill 4 x 9/32” (Ø7mm) dia. holes

(a) at the screw positions using

the Mode Casting (item 2) as a

guide. Insert 4 x ¼”(M6) plugs

into the holes and mount the

Node Casting using suitable

xing screws.

Note: Dedicated Micros does not supply these

ttings, due to the variation in materials

and thickness found on site.

3. Fasten the End Cap Assembly

(item 6) to the Snowdrop

Bracket Welded Assembly

(item 4) using screws (item 1),

spring washers (item 2) and at

washers (item 3) provided.

4. Connect the cable from the

network to the 3 way and 4 way

connector blocks as detailed

in the ‘Electrical Connections’

section of this manual.

Tabla de contenidos

Otros manuales de Cámara de seguridad de Dedicated Micros

Dedicated Micros

Dedicated Micros DM18X Manual de usuario

Dedicated Micros

Dedicated Micros DM/ICE-HYPER-D Manual de usuario

Dedicated Micros

Dedicated Micros 2010 Manual de usuario

Dedicated Micros

Dedicated Micros Oracle Manual de usuario

Dedicated Micros

Dedicated Micros ICE series Manual de usuario

Dedicated Micros

Dedicated Micros 1000 series Manual de usuario

Dedicated Micros

Dedicated Micros DM/ICEVS-BH39 Manual de usuario

Dedicated Micros

Dedicated Micros 504 Manual de usuario

Dedicated Micros

Dedicated Micros CamVu 2000 Manual de usuario

Dedicated Micros

Dedicated Micros CamVu 2000 Manual de usuario

Dedicated Micros

Dedicated Micros 2060 Manual de usuario

Dedicated Micros

Dedicated Micros DM Manual de usuario

Dedicated Micros

Dedicated Micros Dennard 2040 Guía del usuario

Dedicated Micros

Dedicated Micros 2060 Manual de usuario

Dedicated Micros

Dedicated Micros DM/ICEVC-BH39 Manual de usuario

Dedicated Micros

Dedicated Micros DM/CMVUD500 Manual de usuario

Dedicated Micros

Dedicated Micros HyperSense Manual de usuario

Dedicated Micros

Dedicated Micros 2060 Manual de usuario

Dedicated Micros

Dedicated Micros 2060 Manual de usuario

Dedicated Micros

Dedicated Micros Dennard 2040 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario