De Lisle Amp-Speaker Selector 8x6 Pro Manual de usuario

Thank you for purchasing the de Lisle Amp-Speaker Selector 8x6 Pro! Your workflow is about to get a lot more streamlined! Please

read and understand the contents of this manual before connecting your new 8x6 Pro to any of your gear.Should you have any

questions, please contact us directly. We’re happy to help!

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying the product.

10)

11)

12)

13)

14)

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from

the apparatus.

Only use attachments/accessories specified by the manufacturer.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has been dropped.

This product should be operated only from the type of power source indicated in this manual.

SAFETY INSTRUCTIONS

WARRANTY

de Lisle Guitar Company warrants this product to be free from manufacturing defects in material and workmanship under normal use for the

life of the product. If service is required, please contact de Lisle Guitar Company directly. This warranty is void if the product has been:

a) Damaged through misuse, negligence, or abuse. b) Modified or repaired by anyone other than de Lisle Guitar Company. c) Damaged because

it is improperly connected to any other equipment.

Note: This warranty does not cover: a) Ordinary adjustments as outlined in this manual which can be performed by the customer. b) Damage to

equipment connected to the product. c) Any cost incurred in shipping the product for repair. d) Damage to the product not used in the USA.

This warranty is not transferable and only applies to the original purchase. Any implied warranties, including the warranty of merchantability, are

limited in duration to the period of this expressed warranty and no warranty whether expressed or implied shall apply to the product thereafter.

Under no circumstance shall de Lisle Guitar Company be liable for special or consequential damages arising from the use of this product, or for

any delay in the performance of this warranty due to causes beyond our control. Some states do not allow limitations on how long an implied

warranty lasts and/or do not allow the exclusion or limitation of consequential damages, so the above limitations on implied warranty and

consequential damages may not apply to you. This warranty gives you specific legal rights. You may have other rights that vary from state to

state.

FRONT PANEL

INPUT

POWER

LED

FX LOOP

AMPLIFIER

ATTENUATOR

SPEAKER

GROUND

Connect your guitar or pedalboard output here.

The power switch has three positions. Ois off. No power is applied.Amps are muted

at their inputs, amp outputs are connected to a load and loops are put in bypass mode.

In the position, amps are muted but power is still applied to the device. In the third

position , all front panel controls are fully operational.

The LED indicator lights up when power is applied in positions 2 and 3.

If your amp is equipped with an FX loop, you can engage it by placing the switch in the

up position. This will route any FX connected to the FX INPUT and FX OUTPUT to

the corresponding Send / Return jacks on your amp. To bypass your connected FX,

place the switch in the down position.

Rotate to select the desired amplifier. The INPUT jack on the front panel will be

connected to the corresponding AMP INPUT jack on the rear panel. The AMP OUTPUT

jack will be connected to the selected SPEAKER or the ATTENUATOR if it is active. All

unused amps are muted at their inputs, switched to protection loads and their fx loops

are put in bypass mode.

Flip up to bring the connected attenuator in circuit. Use the down position to bypass

the attenuator or if no attenuator is connected to the switch. Your amps will be protected

should you not have an attenuator connected and place the switch in the active position.

Rotate to the select the desired speaker cabinet.

In most cases, this switch should be in the down position. However, should you

experience any noise that might be a grounding issue, place the switch in the up

position. For the GROUND switch to function, the amp must be connected at both the

AMP INPUT and AMP OUTPUT jacks.

REAR PANEL

ATTENUATOR IN

ATTENUATOR OUT

SPEAKER 1-6

Connect to your attenuator’s input jack (e.g. “FromAmplifier”)

Connect to your attenuator’s output jack (e.g. “To Speaker”).

Connect to your speaker cabinets.

AMP OUTPUT 1-8

GND

9V DC

AMP INPUT

Connect to the speaker output jacks of your amplifiers.

Should you experience switching noise when FX are connected to the FX INPUT

and FX OUTPUT jacks and active, find the ground position that is the quietest

with your power supply and FX. NOTE: this switch is disabled when in FX are

bypassed with the FX LOOP switch. Use the front panel GROUND switch in that

case for grounding issues.

Use only 9VDC center-negative power supplies. The switch draws between

110mA and 250mA depending on the settings. Should you hear any “whining” or

see dimming of the LED when functions are switched, the power supply is not

able to deliver enough current for the 8x6 Pro to function properly. We suggest

a 300mA or higher power supply.

Connect to the input jacks of your amplifiers. AMP INPUT 1 must be connected

to a properly ground amplifer to eliminate noise.

REAR PANEL (CONTINUED)

SPECIFICATIONS • Input Impedance: 1 Meg

• Output Impedance: 500 Ohm

• Input Sensitivity: +15 Vp-p

• Switching Time: 4-8ms

• Contact Resistance: 0.075 Ohm

• Power Consumption: 2.6W Max

• Guitar / Pedalboard Input (1)

• Amplifier Input (8)

• FX Send (8)

• FX Return (8)

• Amplifier Output (8)

• Speaker Input (6)

• Attenuator Input (1)

• Attenuator Output(1)

• Attenuator Bypass Switch

• FX Bypass Switch

• FX Input

• FX Output

• Signal Ground Switch

• Power Ground Switch

• Transformer Isolation

• Internally Isolated DC Power Supply

• Silver Relay Contacts with Gold Overlay

• Protection Loads for Unused Amplifiers

• Auto Muting of Unused Amplifiers

• Auto Bypass of Unused Amplifier FX Loops

• Premium 2U Rack Chassis with Laser Etched Panels

• 9VDC 500mA Power Supply Included (300mA Minimum Required)

• Hand-Wired

• 150W Maximum Power

• Lifetime Warranty

make or break any rear panel cable connections with the 8x6 Pro, amplifers, FX or

attenuators powered on.

use this device as a load box. Always be sure to have a proper load connected

whether it is a speaker, load box or attenuator with a built-in load.

exceed the maximum power rating of the device.

leave cables unsupported on the back of the device.

place the device near large magnetic fields such as power transformers. Doing so

may induce a voltage in the isolation transformers which will be heard as hum.

use improper cables. Be sure to use instrument cable for all AMP INPUT, FX INPUT,

FX OUTPUT, SEND and RETURN jacks. Use speaker cable for the AMP OUTPUT,

SPEAKER, ATTENUATOR IN, and ATTENUATOR OUT jacks.

DO NOT

PRECAUTIONS

INITIAL SETUP PROCEDURE

We recommend starting with one amp and checking your progress. With so many

cables, it can be easy to connect things incorrectly.

Be sure all devices are powered off before making any connections. Place the front

panel FX LOOP andATTENUATOR switches in the down position.

Connect a speaker cabinet to SPEAKER 1

Connect an amplifier’s speaker output toAMP OUTPUT 1.

Connect the same amplifier’s input jack toAMP INPUT 1.

If equipped, connect the same amplifier’s FX send jack to theAMP 1 SEND jack and

its FX return jack to the AMP 1 RETURN jack.

Connect the input of your pedalboard or FX unit to the FX INPUT jack and its output

to the FX OUTPUT jack. Note: FX will be bypassed while the front panel FX LOOP

switch is in the down position.

If you have an attenuator, connect its input to the ATTENUATOR INPUT jack and

its output to the ATTENUATOR OUTPUT jack. Note: the attenuator will be bypassed

while the front panel ATTENUATOR switch is in the down position.

Connect your guitar to the front panel INPUT jack. Rotate theAMPLIFIER dial to

position 1. Rotate the SPEAKER dial to position 1.

Power on the 8x6 Pro and then turn on your amplifier.

Listen for the guitar signal. If you hear it coming from the speaker, move on to 12. If

not, double check your cable connections as well as the amplifier and guitar volume

controls. Should you hear ground noise, you may need to move this amp to another

position or place the front panel GROUND switch in the up position.

To test your FX connections, place the FX LOOP switch in the up position. Should the

sound disappear, check your cable connections as well as the FX output level. Should

you hear excessive noise when switching the FX LOOP on or off, try switching the

rear panel GND switch to find the quietest position.

To test your attenuator, place the ATTENUATOR switch in the up position. Should the

sound disappear, check your cable connections as well as the attenuator output level.

Repeat the above steps as necessary to add the rest of your amps and cabinets.

Tabla de contenidos

Otros manuales de Amplificador de De Lisle

De Lisle

De Lisle RUTGERS REVERB AMPLIFIER Manual de usuario

De Lisle

De Lisle KING DADDY Manual de usuario

De Lisle

De Lisle 15P STUDIO Manual de usuario

De Lisle

De Lisle NICKEL BOX Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario