De Agostini Model Space C57 Manual de usuario
Build the
Steam
Locomotive
Pack 05
Contents
Step by step Page
Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP.
Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE.
Published in the USA by De Agostini Publishing USA, Inc.,121 E. Calhoun Street, Woodstock, IL 60098.
All rights reserved © 2016
Warning: Not suitable for children under the age of 14. is product is not a toy and is not designed or
intended for use in play. Items may vary from those shown.
Build the
Steam
Locomotive
Stage 29: The leading truck 3
Stage 30: The leading truck 4
Stage 31: The headlamp
Stage 32: The smokebox door lock
Stage 33: The boiler 1
Stage 34: The boiler 2
Stage 35: The boiler 3
Stage 36: The rebox 1
68
70
72
74
76
78
81
83
Step by step: Stage
Tools
Where your parts t
68
29
The leading truck 3
Equaliser (outer) × 2
Equaliser (inner) × 2
Leaf springs × 2
Hanging links × 4
Nuts (M2) × 4
Screws (2 × 10mm) × 3
Hex head screws (2 × 8mm) × 5
Phillips screwdriver
Pliers
PVA glue
Socket wrench
1
Pass the threaded part of the link
through the hole in the leaf spring,
and tighten a nut onto it.
Lay out a leaf spring, two hanging links and
two nuts, as shown.
Repeat this process to create
two sets, as shown.
Equalisers
Your parts
69
23
The holes in the outer and
inner equalisers are dierent,
as shown above.
Place the equalisers on either side of the leaf
spring. Tighten a hex head screw through the
aligned holes of the outer equaliser, the links
and the inner equaliser.
Make a second set.
Place one of the leaf springs between an
inner and an outer equaliser, along with
two 2 × 8mm hex head screws.
4
Loosen the hex head screws
slightly and then apply some
PVA glue to the ends of them.
Place the assembly over the side frame of
the leading truck, with the equalisers either
side of the frame.
Threaded
Larger hole
without thread
Inner
Outer
Tighten a 2 × 10mm
screw into the hole in
the centre of the leaf
spring, to secure it to
the truck. Secure the
second leaf spring
assembly to the other
side of the truck in the
same way.
Complete
Step by step: Stage
Tools
Where your parts t
70
30
The leading truck 4
Leading wheel A
Leading wheel B (spoked)
Phillips screwdriver
Flat head driver
1
As well as the two leading
wheels from this stage, you will
also need the leading truck, as
well as the side stays, washers,
centre pin and 2 × 4mm screws
from Stage 28.
Make sure that when you are tting the wheels of the leading truck that you have the spoked
wheels at the rear (above left).
Side stays
Washers
Centre pin
Screws 2 × 4mm
Wheels
Your parts
71
2 3
Lay a side stay (Stage 28) over the
left underside of the truck, aligning
the holes (circled).
Tighten a 2 ×
4mm screw
(Stage 28)
into each of
the holes.
4
Place the leading
truck upside-
down and lower
the rst leading
wheels into the
U-shaped area
just behind the
guard irons.
Position the two axles
properly in the frames.
Fit the second
leading wheel
into the
U-shaped area
at the rear of
the truck in the
same way as
the rst wheels.
Pass the centre pin
(Stage 28) down through
the aligned holes.
Align the hole in the centre of
the leading truck with the hole
in the truck support.
Tighten the centre
pin into place.
Axles
Side stay
Washer
2 × 4mm screws
2 × 4mm screws
Fit another side stay to the other side of the
truck with four more 2 × 4mm screws.
Place a washer (Stage 28)
over the hole in the centre of
the truck support. Complete
Step by step: Stage
Tools
Where your parts t
72
31
The headlamp
Headlamp
Lens
Smokebox door handle
LED
Terminals × 2
Connector
Tweezers
Epoxy adhesive
Instant adhesive
1
HeadlampSmokebox door handle
Position the handle so that there is a 1mm
gap between it and the door.
Apply instant adhesive to the ends
of the handle to secure it in place.
Insert the handle into the two holes on the
smokebox door.
1mm
Your parts
73
2
4
3
Apply a small amount of
epoxy adhesive to the
base of the headlamp
(circled, above).
Pass the LED cable into the hole, down into
the smokebox, and then back to the right
side of the spark arrester.
Prepare the LED cable by removing
the cable tie. Straighten the end of the
cable that does not have the LED on it.
Insert the
post at the
bottom of the
headlamp
into the hole
at the top of
the smokebox
(circled).
Continue to feed the cable through the
hole until the LED is in the headlamp.
Align the end of the cable with the
hole in the headlamp.
Adjust the position
of the headlamp
to match the one
shown here. Make
sure it’s aligned
centrally with the
smokebox.
Epoxy adhesive
Complete
Step by step: Stage
Tools
Where your parts t
74
32
The smokebox
door lock
Lock bar
Smokebox door handle
Smokebox door lever
Lock
Superheater header
Handrail A
Handrail B
Handrail brackets × 5
Tweezers
Epoxy adhesive
Synthetic rubber adhesive
1
Smokebox door handle
Handrail
Your parts
Locate the two ridges on either side of
the inside of the smokebox door (circled).
Open the smokebox door, and insert the
lock bar from the front.
Glue the bar between the two ridges on
either side of the smokebox. The hole
in the centre should be positioned as
shown above.
Apply some epoxy adhesive to the space
between the ridges.
75
2
4
3
Turn the lever
onto the handle
as far as it will go.
Insert the end of the
smokebox handle into the
hole in the lever.
Pass the end of the handle into
the hole in the centre of the
smokebox door.
Apply some epoxy adhesive to
the end of the handle. Place the
lock onto the end of the handle.
Adjust the position of the
lock to match the one
shown above.
Apply synthetic
rubber adhesive
to the ends of
the two brackets
holding handrail
B, and insert them
into the two holes
(circled).
Place three
brackets on
handrail A, and
two onto handrail
B, as shown.
Move handrail
B through the
brackets and apply
synthetic rubber
adhesive to the
points where the
brackets were. Then
move the handrail
back into position.
When the lever is rotated
the lock on the inside of the
smokebox turns in the hole
in the centre of the lock bar,
holding the door shut.
Fit handrail A and the
three brackets in the
same way as B. Remove
any excess adhesive from
the rails and brackets.
Epoxy adhesive
Complete
Otros manuales para Model Space C57
4
Otros manuales de Juguete de De Agostini
De Agostini
De Agostini MODEL SPACE SUZUKI GSX 1300R HAYABUSA Manual de usuario
De Agostini
De Agostini Model Space T-72 Manual de usuario
De Agostini
De Agostini Model Space MiG-29 Manual de usuario
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Manual de usuario
De Agostini
De Agostini Model Space IJN Akagi Manual de usuario
De Agostini
De Agostini Millennium Falcon 3 Series Manual de usuario
De Agostini
De Agostini Model Space HUMMER H1 Manual de usuario
De Agostini
De Agostini Model Space T-72 Manual de usuario
De Agostini
De Agostini Model Space ROBI Pack 03 Manual de instrucciones
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Manual de usuario
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Manual de usuario
De Agostini
De Agostini Model Space MiG-29 Manual de usuario
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Manual de usuario
De Agostini
De Agostini Model Space T-72 Manual de usuario
De Agostini
De Agostini Model Space MiG-29 Manual de usuario
De Agostini
De Agostini Model Space C57 Manual de usuario
De Agostini
De Agostini Model Space Harley-Davidson FLSTF Fat Boy Manual de usuario
De Agostini
De Agostini Model Space C57 Manual de usuario
De Agostini
De Agostini Model Space T-72 Manual de usuario
De Agostini
De Agostini Model Space T-72 Manual de usuario
