De Agostini Model Space C57 Manual de usuario

Build the

Steam

Locomotive

Pack 04

Contents

Stage 21: The leaf springs

Stage 22: The second wheels

Stage 23: The third wheels

Stage 24: The connecting rods

Stage 25: The valve gear

Stage 26: The motion plates

Stage 27: The leading truck

Stage 28: The leading truck 2

50-51

52-53

54-55

56-57

58-59

60-61

62-63

64-65

Step by step Pages

Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP.

Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE.

Published in the USA by De Agostini Publishing USA, Inc.121 E. Calhoun Street, Woodstock, IL 60098.

Warning: Not suitable for children under the age of 14. is product is not a toy and is not designed or intended for use in play. Items may vary

from those shown.

Build the

Steam

Locomotive

Step by step: Stage

Tools

Where your parts t

The leaf springs

Leaf springs × 6

Links (medium) × 8

Links (long) × 2

Links (short) × 2

Screws (2 × 8mm) × 11

Screws (2 × 7mm) × 7

Screws (2 × 6mm) × 13

Nuts × 22

Bushes (4.5mm) × 8

Bushes (3.5mm) × 2

Phillips screwdriver

Pliers

Socket wrench (4mm)

Leaf springs

The six leaf springs t together with the three sizes of links, as shown above.

Your parts

Right

First wheels Second wheels Third wheels

Left

Flat surface on the outside

Short links Long linksMedium links

Here you can see how the leaf springs and

links t together, secured by the 2 × 6mm

screws and nuts.

Insert a 4.5mm bush

into the front hole of

the rear equalising

bars. Then, take

the second wheel

leaf spring and

place over the

underframe, so the

bottom of the links

are positioned over

the ends of the

equalising bars.

Pass a 2 × 8mm

screw through the

hole and secure

with a nut. Repeat

this step to t the

other rst wheel

leaf spring to the

right side of the

underframe.

Pass a 2 × 8mm screw through the hole

in the rear link and equalising bar, and

secure with a nut. Repeat this step to t

the right second wheel leaf spring on the

other side.

Take one of the rst wheel leaf

springs and place over the

underframe, inside the motion

frame. Place a 3.5mm bush between

the underframe and the end of the

short link.

Fit the third wheel leaf springs to the rear holes of the

rear equalising bars. The holes in the equalising bars

should all have a 4.5mm bush in them.

Place the links over the ends of

the springs and pass a screw

up through the aligned holes.

Tighten a nut onto the end of

the screw. Repeat this process,

following the photo in the

previous step to assemble all

the leaf springs.

First wheels Second wheels Third wheels

Nut

Screw

Nuts

Screws

Leaf spring

Insert a bush

Complete

Step by step: Stage

Tools

Where your parts t

The second wheels

Second wheels

Axle box A × 4

Axle box B × 4

Axle box guards × 4

Screws (2 × 5mm) × 9

Bushes × 2

Phillips screwdriver

Axle box The second driving wheels

Assemble axle boxes A and B as shown

above. Complete the four sets.

Take one of the axle boxes and slide

it up into the gap in the underframe,

positioning the frame in the grooves

at the side of the axle box.

Test-t the remaining

three axle boxes in the

other spaces in the

underframe.

Your parts

2 3

Place the assembled axle boxes

over the axles of the wheels,

inside the washer at each end

of the axle, with the long part of

axle box A closer to the wheels.

Place an axle box guard onto

the underframe, aligning the

holes with those on either side

of the axle box.

Turn the

underframe over

and lower the axle

boxes back into

place, as shown.

When lifting the underframe to t the

axle boxes and wheels, don’t lift it at the

rear, as the weight of the front may cause

distortion, and the two sides of the frame

may get squeezed together. Instead,

carefully lift the underframe at both ends.

Disassemble the rst

wheels from Stage 3.

Fit the remaining

two axle boxes to

the rst wheels.

Then t them all

into place, securing

them with an axle

box guard and two

2 × 5mm screws.

Tighten a 2 × 5mm screw

into each of the four

circled holes.

Secure with masking tape

The parts from Stage 3

Once they are

pushed all the

way in, you can

remove the

masking tape.

Complete

Tip

Step by step: Stage

Tools

Where your parts t

The third wheels

Bushes (large) × 2

Rod pins × 2

Nuts (M2) × 2

Bushes (small) × 2

Screws (2 × 6mm) × 2

Screws (2 × 5mm) × 5

Third wheels

Connecting rod A

Connecting rod B

Axle box guards × 2

Axle box A × 2

Axle box B × 2

Masking tape

Phillips screwdriver

Pliers

File

Socket wrench (4mm)

Fit the axle boxes into the underframe,

remove the masking tape and then

secure with two axle box guards

and 2 × 5mm screws.

Your parts

Axle box Third wheelsRear side rod

Assemble the axle boxes over the axle of the third

wheels and temporarily secure with masking tape.

Repeat this

to secure the

other ve leaf

springs to the

corresponding

axle boxes.

Secure the leaf spring to the

long part of the axle box with

a 2 × 7mm screw (Stage 21),

as shown.

Identify the two types of

bush: the shorter ones

with smaller central

holes and the longer

with the larger holes.

Insert the rear end

of the coupling rod

into the front of the

connecting rod. Push

a small bush through

the aligned holes, then

pass a 2 × 6mm screw

through the bush and

holes, and tighten a

nut onto the end of

the screw.

Prepare and lay out the

parts from this stage and

Stage 3, as shown in

the photo, right.

Position the assembly from Step 3

along with the three bushes needed

and two rod pins, as shown.

Place the hole at the rear of the coupling

rod over the pin projecting from the

second wheel, then place the bush

(Stage 22) between them. Repeat this

step for the other side of the model.

Second wheel bush (Stage 22)

Slightly longer, inner diameter is larger

First and third wheel bushes

Shorter, inner diameter is smaller

Connecting rod A

Coupling rod A (Stage 3)

Screw

Small bush

Nut

Front

Right

Left side rod

Coupling rod A

(Stage 3)

Coupling rod B

(Stage 3)

Depressed around the hole

Bush

Coupling rod Connecting rod

Bush

Rod pin Rod pin

Left

First wheels Third wheelsSecond wheels

Connecting

rod A

Connecting

rod B

Depressed around the hole

Front

Ledge

Axle box A

Ledge

Bush (Stage 22)

Check the connecting rods for any

ash. Remove any you nd with a le.

Align the hole in the coupling rod with

the hole o-centre of the rst wheel.

Insert a bush into the hole in the rod and

then place the rod pin into the bush,

then tighten it into the wheel. Do this for

the third wheel as well.

Complete

Step by step: Stage

Tools

Where your parts t

Prepare the crossheads

from Stage 16. Arrange

them as shown here.

The connecting rods

Screws (2 × 7mm) × 3

Stepped screws (2 × 4.8mm) × 3

Set screws (2 × 3.8mm) × 3

Hex head screws (1.4 × 4mm) × 9

Wrench

Right connecting rod

Left connecting rod

Eccentric rods × 2

Expansion link central plates × 2

Expansion link outer plates × 2

Expansion link inner plates × 2

Bushes × 2

Eccentric arms × 2

Phillips screwdriver

Flat-head screwdriver

Tweezers

Eccentric rodConnecting rod

Place the two connecting rods

in front of you, as shown here, to

identify the front and rear, and top

and bottom. Check over the rod for

any ash, and remove any you nd.

Crosshead A

Right

Left

Crosshead B

Projection

Raised part

Top

LeftRight

Your parts

2 3

Take crosshead B and slide it

over the motion bar, then insert

the piston rod into the hole in

the cylinder cover.

Place crosshead A onto

crosshead B, inserting the

pin into the hole in the

connecting rod.

Place a bush onto

the crankpin.

Place the hole at

the rear of the left

connecting rod over

the crankpin and place

the front end of the

bar into the crosshead.

Tighten a 2 × 7mm screw into an

eccentric arm, as shown.

Place the eccentric

arm onto the crank

pin, as shown.

Rotate the arm so

the top is about 10

degrees closer to

the front. Tighten

the screw (circled)

to hold the arm in

place. Repeat Steps

2-4 on the right

side of the model.

Assemble a second set of the expansion link

central plate and an eccentric rod. To tell the left

and right assemblies apart in the future, tighten

the screws from the opposite side.

Threaded side

Place between the

two sides

Right

Left

Crankpin

Insert the

piston rod

About 10 degrees

Screw

Tighten a hex head screw into each of

the four holes at the top of the crosshead

using the wrench.

Put the hole of

an expansion

link central plate

into the end of

an eccentric rod.

Tighten a 2 ×

3.8mm set screw

in the hole.

Complete

Otros manuales para Model Space C57

Otros manuales de Juguete de De Agostini

De Agostini

De Agostini MODEL SPACE SUZUKI GSX 1300R HAYABUSA Manual de usuario

De Agostini

De Agostini Model Space T-72 Manual de usuario

De Agostini

De Agostini Model Space SANTISIMA TRINIDAD Manual de usuario

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Manual de usuario

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Manual de usuario

De Agostini

De Agostini Model Space T-72 Manual de usuario

De Agostini

De Agostini Model Space C57 Manual de usuario

De Agostini

De Agostini Model Space T-72 Manual de usuario

De Agostini

De Agostini Model Space MiG-29 Manual de usuario

De Agostini

De Agostini Model Space MiG-29 Manual de usuario

De Agostini

De Agostini Model Space T-72 Manual de usuario

De Agostini

De Agostini Model Space T-72 Manual de usuario

De Agostini

De Agostini Model Space T-72 Manual de usuario

De Agostini

De Agostini Model Space C57 Manual de usuario

De Agostini

De Agostini Model Space MiG-29 Manual de usuario

De Agostini

De Agostini Model Space T-72 Manual de usuario

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Manual de usuario

De Agostini

De Agostini Model Space MiG-29 Manual de usuario

De Agostini

De Agostini Model Space MiG-29 Manual de usuario

De Agostini

De Agostini Model Space C57 Manual de usuario

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Manual de usuario

De Agostini

De Agostini Model Space MiG-29 Manual de usuario

De Agostini

De Agostini Model Space H.M.S. Bounty Admiralty Manual de usuario

De Agostini

De Agostini MODEL SPACE SUZUKI GSX 1300R HAYABUSA Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario