dbx iEQ-15 Guía de instalación
iEQ-15 and iEQ-31
How do you work it? A Quick Overview
AFS FILTERS CAN BE DEPLOYED IN ONE OF TWO PRIMARY MODES.
All Live (Normal Mode). In this mode, the 12 filters per channel are available to be deployed
as feedback occurs throughout a performance.
Six Live, Six Fixed (Mixed Mode). In this mode, half of the filters can be deployed when set-
ting up and “ringing out” the system. These “fixed” filters will remain in place until cleared.
This leaves the remaining six filters in the “live” mode for the remainder of the performance.
Those live filters will deploy to address feedback as needed for a limited (and selectable)
amount of time.
TO SELECT BETWEEN THOSE MODES:
1. On power up, press and hold channel 1 AFS button until the Channel 1 meters show every
other LED lit. Once the AFS button is released the various modes can be selected.
2. Pressing the Channel 1 AFS button cycles through the 3 menus, indicated by each of the
three LED lights on the Channel 1 output meter.
3. Pressing the Channel 1 AFS button twice will light up the Third LED on the Channel 1 out-
put meter indicating that you are now in the menu where you can select between AFS
Normal (12 Live Filters) and AFS Mixed (6 Fixed Filters & 6 Live Filters).
4. Now press the Channel 2 AFS to select either the Normal or Mixed mode by toggling the
LED on the Channel 2 output meter.
5. Pressing and holding the Channel 1 AFS button will allow you to exit the power up menus;
or, proceed to instruction #4 in “Filter Lift” selections on the following page.
CHANNEL 2
AFS Normal vs. 6-Fixed/6-Live Menu
AFS Normal (All Live FIlters)
6-Fixed/6-Live Mode
System Lockout
Power Up Menu
Live Filter Lift Time
AFS Normal vs.
6-Fixed/6-Live
CHANNEL 1
Power Up Prompt CHANNEL 1
®
®
LIVE FILTERS CAN SET TO ONE OF THREE FILTER LIFT SELECTIONS:
This sets the amount of time a live filter remains in effect before it becomes disengaged. The 3 Live
Filters settings are:
• Live Filter Lift Off – The filter remains in effect until all other available filters are in use and
it is needed again in a new position. The filter acts in a “round robin” capacity rotating in
line to address problems as they occur.
• Live Filter Lift 10 Minutes – The filter remains in place for 10 minutes, then checks to see
if it is still needed before it releases and is available for use again.
• Live Filter Lift 1 Hour – The filter remains in place for 1 hour, then checks to see if it is
still needed before it releases and is available for use again.
TO SELECT LIVE FILTER LIFT SETTINGS:
1. On power up, press and hold channel 1 AFS button until the Channel 1 meters show every
other LED lit.
2. Once the AFS button is released, the various modes can be selected.
3. Pressing the Channel 1 AFS button cycles through the menus. This is indicated by changes
in the LED’s on the Channel 1 output meters.
4. Press the Channel 1 AFS button until it lights up the Second LED on the Channel 1 output
Meter indicating that you are in the Live Filter Lift Selection mode.
5. Pressing the Channel 2 AFS allows you to toggle between the three settings indicated by
LED’s on Channel 2 output meter.
Live Filter Lift Off (1st LED)
Live Filter Lift 10 Minutes (2nd LED)
Live Filter Lift one Hour (3rd LED)
6. Pressing and holding the Channel 1 AFS button will allow you to exit the power up menus,
or proceed to instruction #4 below in “Front Panel Control Lock Out Feature.”
CHANNEL 2
Live Filter Lift Time Menu
Live Filter Lift Off
Live Filter Lift Short
Live Filter Lift Long
FRONT PANEL CONTROL LOCK OUT FEATURE
1. On power up, press and hold channel 1 AFS button until the Channel 1 meters show every
other LED lit.
2. Once the AFS button is released, the various modes can be selected.
3. Pressing the Channel 1 AFS button cycles through the menus. This is indicated by changes
in the LED’s on the Channel 1 output meters.
4. Press the Channel 1 AFS button until it lights up the First LED on the Channel 1 output
Meter indicating that you are in the System Lockout menu.
5. Pressing the Channel 2 AFS button allows you to toggle between the two settings indicated
by LED’s on Channel 2 output meter.
6. Pressing and holding the Channel 1 AFS button will allow you to exit the power up menus.
FILTERS CAN BE USED IN ONE OF THREE “WIDTHS”
We refer to them as:
1. “Music as a high priority” (Up to 1/80th of an octave)
2. “Music as a medium priority” (Up to 1/20th of an octave)
3. “Music as a low priority” (Speech applications. Up to 1/10th of an octave)
Filter widths can be easily selected per channel on the unit by depressing the AFS LED button until it
displays the color associated with each filter width.
High (Red)
Medium (Yellow)
Low (Green)
AFS Off (No light)
System Lockout Menu
System Unlocked
System Locked
CHANNEL 2
FILTERS CAN BE CLEARED AND RE-SET
•To clear all filters (both Live and Fixed), depress the AFS button for a few seconds until
the LED meter adjoining it flashes, indicating that the filters have been cleared.
• Live Filters can be cleared, leaving Fixed Filters in place. Turning the unit off re-sets
(clears) the live filters but not the fixed filters. Those can only be cleared using the above
procedure.
18-0248-A
Otros manuales para iEQ-15
3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Ecualizador estéreo de dbx
dbx
dbx DriveRack 480 Manual de usuario
dbx
dbx DriveRack 4800 Manual de usuario
dbx
dbx DriveRack 442 Manual de usuario
dbx
dbx DriveRack 4820 Manual de usuario
dbx
dbx DriveRack 480 Manual de usuario
dbx
dbx 30 Series Manual de usuario
dbx
dbx iEQ-15 Manual de usuario
dbx
dbx iEQ-31 Manual de usuario
dbx
dbx 2231 Manual de instalación y operación
dbx
dbx DriveRack 4800 Manual de usuario
dbx
dbx 1215 Manual de usuario
dbx
dbx DriveRack 480 Manual de usuario
dbx
dbx DriveRack 480 Manual de usuario
dbx
dbx 14 Manual de usuario
dbx
dbx DriveRack 480 Manual de usuario
dbx
dbx 12 Series Manual de usuario
dbx
dbx 2215 Manual de instalación y operación
dbx
dbx 131, 215, 231 Manual de usuario
dbx
dbx 131, 215, 231 Manual de usuario
dbx
dbx DriveRack 4800 Manual de usuario
