Dbx Detection and the Dynamics Duo Manual de usuario

Detection and the Dynamics Duo

(OrWhy Do Some Compressors Sound

GreatWhile Others Just Plain Don’t?)

Roger Johnsen

Detection and the Dynamics Duo (or Why Do Some Compressors Sound Great

While Others Just Plain Don’t?) A Discussion of the Benefits of True RMS Level

Detection and True RMS Power Summing

Detection? Dynamics Duo? Sounds like a confidential Gotham City document that Cat

Woman or the Riddler would like to get a hold of for blackmail purposes.Perhaps the terms

“sidechain”and“compression”sound a little more familiar.In this paper,we talk about these

terms and explain the important role that “detection” plays in a well-designed “dynamics

processor”.Although we briefly mention VCA’s, the purpose of this paper is to highlight

various detection schemes used by manufacturers, as well as the methods used to link

channels for stereo operation.We describe our True RMS Level Detection and True RMS

Power Summing methods that we at dbx profess to be the correct and logical, not to

mention best sounding ways to do dynamics processing.

1.Viscerally CompressedAmplitude

No,that’s not what“VCA”stands for,as anyone familiar with compressors could tell you,

but we have a gut feeling you already knew that (pun intended)! VCA, of course, means

“Voltage Controlled Amplifier.”The guts of any dynamics processor (compressor, limiter,

expander, gate, ducker, dynamic filter, modulator, etc.) contain, among other things, a VCA.

As a pioneer in the field ofVCAs,dbx created the patented industry standard chip used by

the zillions by many major manufacturers of professional and consumer audio equipment.

You’ll find our chips in dbx noise reduction systems throughout the world.

But this paper is not aboutVCA’s.We know that it takes more than a greatVCA to make

a great compressor. Much more.And that’s where the years of leadership and expertise in

dynamics processing design make all the difference.

2.Dynamics Duo

The real art in making a great compressor is not only in the design and implementation

of theVCA,but in the design of the other,more important half of the

Detection and the Dynamics Duo - November 1998 Page 1

Detection and the Dynamics Duo

compressor.Any dynamics processor consists of the“Dynamics Duo"”or two signal paths:

an audio path through the VCA that needs to be as clean as possible--low noise, low

distortion--and a detector path that contains the smarts to figure out what to tell theVCA to

do.The detector path is often referred to as the“sidechain.”(Sounds like a wallet protection

device).The sidechain consists of an audio level detector that converts the audio signal from

which the compressor is "keying" to a control voltage.This control voltage is then modified

by the threshold, ratio, attack, release, (etc.) controls which follow the detector. This

modified voltage controls the gain of theVCA.

If it sounds like Mr. Sidechain is the real brains of the Dynamics Duo,while Mr.VCA is

just the brawn, you’re absolutely right.The particular sound of any dynamics processor is

due more to the way Mr.Sidechain handles his affairs than how well Mr.VCA carries out his

orders. Common problems such as the proverbial “pumping” and “breathing” in some

compressors results from sidechain circuitry design,not fromVCA deficiencies.But,lest we

fail to give credit where credit is due, never underestimate the essential role that Mr.VCA

plays in providing a clean signal free of noise and distortion.

3.Detection:RMS —True or False?

The principal component of the sidechain is the detector, and its ability to accurately

detect audio levels in the proper way considerably affects the dynamics of the processed

signal.Common sense would tell you that,given a particular audio signal,the detector must

compute a result that corresponds to the result computed by the human ear,if that detector

is to truly function as an audio detector.

There are many ways to do audio level detection, and as you may surmise, different

detection methods yield different results. While some compressor/limiters use peak

detection and fast response characteristics,their action is frequently displeasing to the ear,

even at modest compression ratios, as rapid gain changes result in unnatural signal

dynamics.This is due to the psychoacoustic phenomenon that the human ear responds,not

to the peaks,but to the average power of the signal.In other words,the ear responds to the

sum of the energies of all frequency components present.

Detection and the Dynamics Duo - November 1998 Page 2

Detection and the Dynamics Duo

Detection and the Dynamics Duo - November 1998 Page 3

Detection and the Dynamics Duo

Other processors use averaging circuits for level detection, created by simple resistor-

capacitor (RC) filters which may approximate average power with some waveforms,but in

general will not coincide with the way the human ear and brain interpret sound.This is

because there is not a one-to-one correspondence between the average amplitude of a

waveform and the average power of that same waveform,resulting in a mismatch between

the detector’s calculated signal level and your ear’s perceived level. It’s as if the averaging

detector is looking at the signal world through“fun house”mirror lenses.

A related method that has gained some popularity of late,due mainly to the availability

of these particular detector chips to the general public, is the “log average” method. But,

again, using averaging techniques, these logarithmic detectors exhibit the same error in

calculating signal level as illustrated above.Given these explanations,perhaps we have shed

some light on reasons why most processors work great only in certain situations with

certain types of signals.

Obviously, this is not the dbx way. Our processors use True RMS Level Detection for

signal sensing to most closely emulate human hearing response. Without going into a

detailed technical explanation, the mathematical concept of RMS (Root Mean Square)

describes an effective value of voltage or current that results in average power.This effective

value is called RMS because we take the square root of the mean of the squared values.

Disregarding the technical mumbo jumbo, just remember that the RMS value inherently

corresponds to the average power of the signal,as does the response of the human ear.With

sophisticated chips developed at dbx, utilizing patented integrated circuit designs to

calculate the RMS value of the signal,we are able to create unrivaled dynamics processors

with natural sound with the most listenable results over the widest range of signals.Those

who have used dbx processors know this to be true.

4.Duo Dynamics

What about stereo dynamics processing? Is there a special way required to link two

channels of compressors for processing a stereo signal, or do we just run each channel

through its own independent compressor?Those familiar with compressors know that for

processing stereo signals, each channel must react identically--that is, their VCA’s must be

Detection and the Dynamics Duo - November 1998 Page 4

locked together so that their gains change identically--otherwise,the stereo image will shift

to the side with less gain reduction occurring at that instant.

We agree that theVCA’s must react identically when linked,but which detector controls

both VCA’s? Do they react to the left channel detector,or to the right channel detector, or

both?And,if to both,how? Do they react to the greater of the two signals? Do they react to

the sum of the signals?At this point you’re probably asking,“Who the @%&!*% cares?!”Well,

for starters,your ears and brain care.Bottom line:the detectors of both channels need to be

linked in an intelligent way.Let’s take a look at some not-so-intelligent ways and,of course,

the dbx way.

5.The Sum OfThe Squares OfThe Average of the Hypotenuse Sounds Bad! (OrWhyWe Do

ItTheWayWe Do!)

One way to do stereo linking is to ignore one of the channels,either the left one or the

right one, and have both VCA’s react to the signal on that one channel only. So which

channel signal do you choose to pay attention to and which one do you ignore, allowing

damaging peaks,speaker overexcursions,or fatal jaunts into digital 0VU land? If this seems

like a pointless question because no manufacturer would be stupid enough to implement

this method on a stereo processor, guess again.A particular manufacturer with a German-

sounding name whose boxes are made in China has implemented this method on their

“stereo” box. Hmm? Incidentally, their chosen method of detection on this box is the log

average method.

Another way to link detectors is to sum the left and right channel signals together before

going into one detector as suggested in an application note of a particular manufacturer of

anotherVCA.On the surface,this may seem like an acceptable way and will sometimes give

acceptable results,especially if the left and right signals are identical.The problem is that the

signals are,by definition,stereo!There is no problem detecting mono signals since they add

together without phase cancellation,but we’re not processing mono signals when we’re in

stereo link mode!

Stereo signals are,of course,different to some degree and will combine with some phase

cancellation.In other words,peaks in phase add together while peaks out of phase cancel.

Therefore, using this method, the detector will not calculate the correct level of the

Detection and the Dynamics Duo

Detection and the Dynamics Duo - November 1998 Page 5

Detection and the Dynamics Duo

combined power of the left and right signals.The more dissimilar the left and right signals

are, the more error in the detector’s calculated level. It’s as if someone’s continuously

messing with the threshold knob!A much better method,although still deficient,is to link

log average detectors.This results in the sum of the average signal amplitudes, but, as we

have stated before,does not correspond with average power and therefore does not sound

as good.

6.True RMS Power Summing

The dbx way, of course, is different.With our True RMS Power Summing, the linked

detectors respond to the sum of the energy (power) of each channel’s RMS signal.The

intelligence of these RMS detectors allows the signals to be converted to the power domain,

then summed together in the power domain.This produces a true sum of the energies.The

more total energy,the higher the detectors calculate the combined signal to be.This is how

your ears work--the more screaming children in one room (i.e.,the more total energy),the

more irritated you get!

This sum of energies will gain track accurately over a wide dynamic range providing

excellent response at low or high signal levels. No phase cancellation, no inaccurate

modeling of human hearing response,and heaven forbid,no ignoring one channel of signal

information.When detectors are linked intelligently and sum signals the same way that your

ears do,compression,limiting,or expansion will sound the way it should!

7.Conclusion

No need for a conclusion here.You make your own. Thousands upon thousands of

industry professionals have already made theirs, making dbx the most respected and most

used dynamics processing line on the planet.

8760 South Sandy Pkwy.

Sandy, Utah 84070

Phone: (801) 568-7660

Fax: (801) 568-7662

IntÕl Fax: (219) 462-4596

Questions or comments?

E-mail us at: [email protected]

or visit our World Wide Web home page at:

www.dbxpro.com

A Harman International Company

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

Advantech

Advantech ASMB-935 Series Manual de usuario

dbx Detection and the Dynamics Duo Manual de usuario

Manuales populares de Hardware de computadora de otras marcas