DaytonAudio WP8BT Manual de usuario
8” IP55 INDOOR/
OUTDOOR PENDANT
SPEAKER 70V/100V
WITH 8 OHM BYPASS
Model: WP8BT/WP8WT
User Manual
2
Thank you for purchasing the Dayton Audio ®8” pendant speaker.This rugged, all-purpose
speaker is designed to deliver reliable, high-quality audio in commercial and residential
applications, while withstanding outdoor environments. The WP8 features an IP55 weath-
er-resistant ABS construction, 2-way coaxial speaker design.
• 8" woofer with coaxial 1" tweeter
• Integral 70V/100V transformer with selectable taps and 8 ohm bypass
• Suitable for indoor or outdoor installation
• Availableinblackorwhitenish
Please read these instructions completely before you begin your installation.
1) Speaker Connection
Remove about 8" of the cable jacket to expose the inner conductors. Strip 1/4" of in-
sulation from each conductor and connect to the speaker terminals. When connect-
ing the wires to the speakers, be sure to observe proper polarity for the best sound.
Most CL2 rated speaker cable will have red and black colored wires inside the
jacket. Connect the red wire to the (+) terminal and the black wire to the (-) terminal.
The red (+) and black (-) speakers wires should correspond to the same terminals
ontheamplier.
NOTE: If this speaker will be used with a 70V/100V distributed audio system, do
not set the 70V/100V tap to the 8 ohm setting. Doing so may damage your speaker
when playing. To use this speaker with a conventional (non-70V/100V) audio sys-
tem, change tap to the 8 ohm setting. If you are unsure what type of audio system
you have, consult a professional installer before continuing.
Step 1: Remove the speaker end cap
Usingascrewdriverorotherat-bladetool,turnthetapselectorknobtothedesired
setting. Selecting the 8 ohm setting will remove the transformer from the signal path
andallowaconventionalampliertodrivethespeaker.Ifusinga70V/100Vsystem
choose the appropriate output setting for the application.
Step 2: Reinstall speaker end cap
Once you have selected the correct setting and mounting bracket you can feed the
speaker wire through the end cap and reinstall.
Typical 70V/100V installation wiring method
3
Mounting Diagram
2) Choose Speaker Location
If you will be installing your speaker outdoors, select a location that is protected from
rain, snow, and out of direct sunlight for extended product life.
CAUTION: Be certain that there are no electrical wires, water pipes, or heating
ducts in the planned installation area before you begin drilling. If there is an electri-
cal outlet nearby, turn off the circuit breaker to avoid possible injury.
NOTE: Your Dayton Audio WP8 speaker is compact, but substantial in weight.
Speaker should be mounted to a solid structure, not drywall. If drywall mounting is
required,usehigh-strengthanchorsdesignedforheavyloadssuchaslightxtures.
To avoid personal injury, please make sure the location you choose for mounting
your speakers can safely support their weight.
Dayton Audio®Last Revised: 1/19/2021
daytonaudio.com
tel + 937.743.8248
info@daytonaudio.com
705 Pleasant Valley Dr.
Springboro, OH 45066
USA
5-Year Limited Warranty
See daytonaudio.com for details
Specifi cations
Model number:.......................... WP8BT/WP8WT
Description:............................... Commercial indoor/outdoor speaker
Woofer: ..................................... 8"mineral-lledpolypropylene
Tweeter:.................................... 1" fabric
Frequency response:................ 50-20,000 Hz
Impedance:............................... 8 ohms/70V/100V
70V/100V taps:......................... 8 ohms/3.75W, 7.5W, 15W, 30W, 60W
Power handling (RMS/Peak): ... 75W/150W
SPL:.......................................... 89.5 dB @ 8 ohm setting, 2.83V/1m
Dimensions:.............................. 18-1/2" height, 9-1/2" diameter
Color:........................................ Black or white available
Weight: ..................................... 9.2 lbs
Ingress protection rating:.......... IP55
3) Troubleshooting
Should your speakers not work properly, check the following:
No sound from speaker or quiet/strange sound:
•Make certain you observed proper polarity for speaker inputs. Check the con-
nections at the back of the receiver, and then at the speaker.
• Verifythattheamplierispoweredonandthevolumeisturnedup.
•Check that the correct transformer tap is selected for your application. If you
areusingastereoamplierorareceiver,usethe8ohmtap.
•Mute feature or protection mode is activated. Check for short circuits in speak-
er wiring.
Amplifi er/Receiver cuts out:
•This could be caused by a short circuit between the positive and negative
leads. Check the connections at the back of the receiver, and then at the
speaker; make sure that no strands of wire from one connector are touching
the other connector.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Oradores de DaytonAudio
DaytonAudio
DaytonAudio MARK1 Manual de usuario
DaytonAudio
DaytonAudio MARK2-WF Manual de usuario
DaytonAudio
DaytonAudio MK442 Manual de usuario
DaytonAudio
DaytonAudio B652 Manual de usuario
DaytonAudio
DaytonAudio SAT-BK Manual de usuario
DaytonAudio
DaytonAudio B652-AIR Manual de usuario
DaytonAudio
DaytonAudio BST-300EX Manual de usuario
DaytonAudio
DaytonAudio MARK2-WF Manual de usuario
DaytonAudio
DaytonAudio BS36 Manual de usuario
DaytonAudio
DaytonAudio B452 Manual de usuario
DaytonAudio
DaytonAudio WP65WT Manual de usuario
DaytonAudio
DaytonAudio RS621 Manual de usuario
DaytonAudio
DaytonAudio B652-AIR Manual de usuario
DaytonAudio
DaytonAudio ME525MTM Manual de usuario
DaytonAudio
DaytonAudio MKBOOM Manual de usuario
DaytonAudio
DaytonAudio VS8 Manual de usuario
DaytonAudio
DaytonAudio I065XTW Manual de usuario
DaytonAudio
DaytonAudio ME650C Manual de usuario
DaytonAudio
DaytonAudio AERO Manual de usuario
DaytonAudio
DaytonAudio IO8XTW Manual de usuario
