DaytonAudio WP65WT Manual de usuario

6-1/2"IP66 INDOOR/

OUTDOOR PENDANT

SPEAKER PAIR 70V/100V

WITH 8 OHM BYPASS

WHITE

Model: WP65WT User Manual

Congratulations on the purchase of your Dayton Audio®WP65WT speaker. This rugged,

all-purpose speaker is designed to deliver reliable, high-quality audio in commercial and

residential applications, while withstanding outdoor environments. The WP65WT features

an IP66 weather-resistant ABS construction, 2-way coaxial speaker design.

• 6.5" woofer with coaxial 1" tweeter

• Versatile mounting brackets for pendant mount, wall mount, or landscape applications.

• Integral 70V transformer with selectable taps and 8 ohm bypass

• Suitable for indoor or outdoor installation

Please read these instructions completely before you begin your installation.

1) Speaker Connection

Remove about 8" of the cable jacket to expose the inner conductors. Strip 1/4" of in-

sulation from each conductor and connect to the speaker terminals. When connect-

ing the wires to the speakers, be sure to observe proper polarity for the best sound.

Most CL2 rated speaker cable will have red and black colored wires inside the

jacket. Connect the red wire to the (+) terminal and the black wire to the (-) terminal.

The red (+) and black (-) speakers wires should correspond to the same terminals

on the amplier.

NOTE: If this speaker will be used with a 70V/100V distributed audio system, do

not set the 70V/100V tap to the 8 ohm setting. Doing so may damage your speaker

when playing. To use this speaker with a conventional (non-70V/100V) audio sys-

tem, change tap to the 8 ohm setting. If you are unsure what type of audio system

you have, consult a professional installer before continuing.

Step 1: Remove the speaker end cap

Using a screwdriver or other at-blade tool, turn the tap selector knob to the desired

setting. Selecting the 8 ohm setting will remove the transformer from the signal path

and allow a conventional amplier to drive the speaker. If using a 70V/100V system

choose the appropriate output setting for the application.

Step 2: Reinstall speaker end cap

Once you have selected the correct setting and mounting bracket you can feed the

speaker wire through the end cap and reinstall.

Typical 70V/100V installation wiring method

(A) Wall Mount (B) Pendant Mount

2) Choose Speaker Location

Simply place them 5-8 feet apart wherever you desire music for the best possible

performance. If you will be installing your speakers outdoors, select locations facing

your listening area that are protected from rain, snow, and out of direct sunlight for

extended product life.

CAUTION: Be certain that there are no electrical wires, water pipes, or heating

ducts in the planned installation area before you begin drilling. If there is an electri-

cal outlet nearby, turn off the circuit breaker to avoid possible injury.

NOTE: Your Dayton Audio WP65WT speaker is compact, but substantial in weight.

Speaker should be mounted to a solid structure, not drywall. If drywall mounting is

required, use high-strength anchors designed for heavy loads such as light xtures.

To avoid personal injury, please make sure the location you choose for mounting

your speakers can safely support their weight.

Dayton Audio®Last Revised: 5/13/2021

daytonaudio.com

tel + 937.743.8248

info@daytonaudio.com

705 Pleasant Valley Dr.

Springboro, OH 45066

USA

5-Year Limited Warranty

See daytonaudio.com for details

Specications

Model number:.......................... WP65WT

Description:............................... Commercial indoor/outdoor speaker

Woofer: ..................................... 6.5" mineral-lled polypropylene

Tweeter:.................................... 1" fabric

Frequency response:................ 60-20,000 Hz

Impedance:............................... 8 ohms/70V

70V/100V taps:......................... 8 ohms/NC/20W/10W/5W/2.5W

Power handling (RMS/Peak): ... 40W/80W

SPL:.......................................... 87 dB / 88 dB @ 8 ohm setting, 2.83V/1m

Dimensions:.............................. 10-1/4" height, 8-1/8" diameter

Color:........................................ White

Weight: ..................................... 4.2 lbs

Ingress protection rating:.......... IP66

3) Troubleshooting

Should your speakers not work properly, check the following:

No sound from speakers or quiet/strange sound:

•Make certain you observed proper polarity for both speaker inputs. Check the

connections at the back of the receiver, and then at the speaker.

• Verify that the amplier is powered on and the volume is turned up.

•Check that the correct transformer tap is selected for your application. If you

are using a stereo amplier or a receiver, use the 8 ohm tap.

•Mute feature or protection mode is activated. Check for short circuits in speak-

er wiring.

One speaker is playing while the other is not playing or plays quietly:

•Check the balance control on the receiver. Make sure it is centered.

•

Loose connection at either the receiver or the speaker. Double check connections.

•Bad speaker cable. Replace the suspect speaker cable.

Amplier/Receiver cuts out:

•This could be caused by a short circuit between the positive and negative

leads. Check the connections at the back of the receiver, and then at the

speaker; make sure that no strands of wire from one connector are touching

the other connector.

Tabla de contenidos

Otros manuales de Oradores de DaytonAudio

DaytonAudio

DaytonAudio MK442 Manual de usuario

DaytonAudio

DaytonAudio ME525MTM Manual de usuario

DaytonAudio

DaytonAudio BST-300EX Manual de usuario

DaytonAudio

DaytonAudio WP4BT Manual de usuario

DaytonAudio

DaytonAudio C452 Manual de usuario

DaytonAudio

DaytonAudio T652 Manual de usuario

DaytonAudio

DaytonAudio MARK2-WF Manual de usuario

DaytonAudio

DaytonAudio MKBOOM Manual de usuario

DaytonAudio

DaytonAudio ME652C Manual de usuario

DaytonAudio

DaytonAudio MARK1 Manual de usuario

DaytonAudio

DaytonAudio B652 Manual de usuario

DaytonAudio

DaytonAudio WP8BT Manual de usuario

DaytonAudio

DaytonAudio AERO Manual de usuario

DaytonAudio

DaytonAudio B652 Manual de usuario

DaytonAudio

DaytonAudio IO525B Manual de usuario

DaytonAudio

DaytonAudio CS620W Manual de usuario

DaytonAudio

DaytonAudio QS204-4 Manual de usuario

DaytonAudio

DaytonAudio Shadow Sound SS3 Manual de usuario

DaytonAudio

DaytonAudio XRA25 Manual de usuario

DaytonAudio

DaytonAudio ME650C Manual de usuario

DaytonAudio

DaytonAudio Contractor Series Manual de usuario

DaytonAudio

DaytonAudio CS620C Manual de usuario

DaytonAudio

DaytonAudio UA721 Manual de usuario

DaytonAudio

DaytonAudio VS8 Manual de usuario

Manuales populares de Oradores de otras marcas

argon audio

argon audio IE20 Manual de usuario

Denon

Denon SC-N7 Manual de usuario

Gemline

Gemline Ace 3952 Manual de usuario

Focal

Focal ON WALL 300 Manual de instrucciones

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manual de usuario

SoundLogic

SoundLogic BCCS-6/6395 Manual de usuario

Peavey

Peavey DTH 218 Manual de usuario

Avantree

Avantree Pluto Air Manual de usuario

Morel

Morel Integra Series INTEGRA OVATION 4 Manual de usuario

Oppo

Oppo SONICA Manual de usuario

Bose

Bose SoundLink Wireless Music System Manual de usuario

Rocksteady

Rocksteady Stadium Manual de usuario

Bowers & Wilkins

Bowers & Wilkins 4 Manual de usuario

Sonance

Sonance SONOS OUTDOOR Series Manual de usuario

Electro-Voice

Electro-Voice EVID FM4.2 Manual de usuario

Pioneer

Pioneer XW-HTD630 Manual de usuario

Onn

Onn BWA16AA002 Manual de usuario

HP GL313AA - USB Speakers PC Multimedia Manual de usuario