Datalogic DS1500-1100 Manual de usuario

DS1500 QUICK GUIDE

DS1500

General View:

4 8

5 Mounting Holes

Good Read LED

External Trigger/Ready LED

Tx Data/Active LED

Laser On LED

Laser Beam Output Window

Test Key

Power On LED

Warning and Device Class Label

Product Label

15-pin D-sub Male Connector

Figure A

For further details on product installation, see the complete Reference Manual.

DS1500 can be configured through the WinHost Windows-based software program available on the

installation CD-ROM (part number 93ACC1771).

For configuration it is necessary to create a cable connecting the scanner to the PC as indicated in the

“How To Build A Simple Interface Test Cable” section of this guide.

56 7

10 11

DS1500 QUICK GUIDE

Power Supply:

- This product is intended to be installed by Qualified Personnel only.

- All Models:

This accessory device is intended to be supplied by a UL Listed or CSA Certified Power Unit with «Class 2» or

LPS power source, which supplies power directly to the scanner via the 15-pin connector.

The scanner is classified as a Class 2 laser product according to EN 60825-1 regulations and as a Class II laser

product according to CDRH regulations.

Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to

hazardous laser light.

There is a safety device, which allows the laser to be switched on only if the motor is rotating above the threshold

for its correct scanning speed.

The laser beam can be switched off through a software command (see also the WinHost Help On Line).

Warning and Device Class Label

The laser diode used in this device is classified as a class 3B laser product according to EN 60825-1 regulations

and as a Class IIIb laser product according to CDRH regulations. As it is not possible to apply a classification

label on the laser diode used in this device, the following label is reproduced below.

LASER LIGHT

AVOID EXPOSURE TO BEAM

CLASS 3B LASER PRODUCT

MAX. OUTPUT RADIATION 35 mW

EMITTED WAVE LENGTH 630~680 nm

TO EN 60825-1 (2001)

Laser Diode Class Label

Any violation of the optic parts in particular can cause radiation up to the maximum level of the laser diode (35

mW at 630 to 680 nm).

DS1500 QUICK GUIDE

Model Description:

DS1500 - X X 0 0

Optical Resolution

1 = Standard Resolution

2 = High resolution

Communication Interface

1 = RS232/RS485main + RS232 aux

Reading Performance:

Version Reading Distance Max Code

Resolution Speed

mm (mils) scans/s

1100 40 mm (1.6 in) - 240 mm (9.4 in) on 0.50mm (20 mils) codes 0.20 (8) 1200

1100 75 mm (2.9 in) - 115 mm (4.5 in) on 0.15mm (6 mils) codes 0.15 (6) 800

2100 50 mm (2 in) - 125 mm (4.9 in) on 0.20mm (8 mils) codes 0.10 (4) 800

Technical Features:

ELECTRICAL FEATURES

Input Power

Supply voltage 5 Vdc±5%

Power consumption max. 2 W

Serial Interfaces

Main RS232; RS485 Full-duplex / Half-duplex

Auxiliary RS232

Baud Rates 150 to 115200

Inputs External Trigger

Voltage max. 40 Vdc

Outputs OUT1, OUT2

VCE max. 40 Vdc

Collector current max. 20 mA continuous;

VCE saturation 0.3V at 6 mA max.

Power dissipation max. 100 mW at 45 °C (Ambient temp.)

OPTICAL FEATURES

Light source Semiconductor laser diode

Wave length (Note 1) 630 to 680 nm

Safety class Class 2 - EN 60825-1; Class II - CDRH

READING FEATURES

Scan rate (software programmable) 800 to 1200 scans/sec

Aperture angle

Maximum Reading distance See reading diagrams

Maximum resolution

USER INTERFACE

LED indicators Laser ON, Tx Data/ACT, Ext Trig/RDY,

Good Read, Power ON

DS1500 QUICK GUIDE

SOFTWARE FEATURES

READABLE CODE SYMBOLOGIES

* EAN/UPC * Code 93

EAN/UPC (including Add-on 2 and Add-on 5) * Code 128

* 2/5 Interleaved * EAN 128

* Code 39 (Standard and Full ASCII) ISBT 128

* Codabar Pharmacode

*ACB Readable. Other symbologies available on request.

Code Selection up to six different codes during one reading phase

Decoding Safety can enable multiple good reads of same code

Headers and Terminators up to four headers and four terminators

Operating Modes On-Line, Serial-On-Line, Automatic, Continuous, Test

Configuration Modes • through menus using WinHost utility

• receiving commands from one of the serial ports (HOST

MODE)

Special Functions ACB (Advanced Code Builder)

Motor Off

Parameter Storage Non-volatile internal EEPROM

ENVIRONMENTAL FEATURES

Operating temperature (Note 2) 0° to 45 °C (32° to 113 °F)

Storage temperature -20° to 70 °C (-4° to 158 °F)

Humidity max. 90% non condensing

Vibration resistance 14 mm @ 2 to 10 Hz

EN 60068-2-6

2 hours on each axis

1.5 mm @ 13 to 55 Hz

2 g @ 70 to 200 Hz

Shock resistance

EN 60068-2-27

3 shocks on each axis 30 g; 11 ms

Protection class IP65

PHYSICAL FEATURES

Mechanical dimensions 40 x 30 x 22 mm (1.57 x 1.18 x 0.86 in)

Weight without cable 44 g (1.55 oz)

Note 1: The features given are typical at a 25 °C ambient temperature (if not otherwise indicated).

Note 2: If the reader is used in high temperature environments (over 40 °C), it is advised the use of the Beam-

shutter (see the WinHost configuration program) and/or a thermal conductive support (such as the

metal bracket provided).

DS1500 QUICK GUIDE

Accessories:

Name Description Part Number

CONFIG / DOC PKG DS1500 Configuration SW, Reference Manual, Test Chart, other

documentation

93ACC1771

Electrical Connections:

DS1500 is equipped with a cable terminated by a 15-pin male High Density D-sub connector for connection to the

power supply and input/output signals.

CAUTION

Do not connect GND and SGND to different (external) ground references. GND and SGND are

internally connected through filtering circuitry which can be permanently damaged if subjected

to voltage drops over 0.8 Vdc.

The details of the connector pins are indicated in the following table:

15-pin male high density D-sub connector pinout

Pin Name Function

1 VS Power supply input voltage +

5 GND Power supply input voltage -

8 PE Protective Earth Ground

13 SHIELD Cable Shield

9 EXT TRIG - External Trigger -

7 OUT1 + Output 1 +

14 OUT2 + Output 2 +

11, 12, 15 NC Not Connected

15-pin D-sub High-Density Male Connector

Pin RS232 RS485

Full-Duplex

RS485

Half-Duplex

2 TX232 Main TX485- RTX485-

3 RX232 Main RX485+

6 TXAUX TX485+ RTX485+

10 RXAUX RX485-

4 SGND SGND SGND

DS1500 QUICK GUIDE

Mechanical Installation:

3.9

[0.15]

[1.18]

13.7

[0.54]

34.1

[1.34]

5.3

[0.21]

7.6

[0.30]

31.3

[1.23]

3.1

[0.12]

N°2

4.6

[0.18]

[0.87]

[1.57]

[0.04]

inch

MØ2

3.2

[0.13]

3.2

[0.13]

[0.43]

[0.24]

[2.44]

[0.79]

[0.98]

1.5

[0.06]

inch

7.1

[0.28]

31.8

[1.25]

31.8

[1.25]

25.1

[0.99]

[0.47]

* The quote refers to the scan line

DS1500 Overall Dimensions Mounting Bracket Overall Dimensions

Skew

Pitch

DS1500 QUICK GUIDE

Input/Output Connections:

INPUT CONNECTIONS

EXT TRIG -

5 GND

EXTERNAL TRIGGER

Ground

DS1500

Signal

+ 5 V

47 K

External Trigger Input Command using Scanner Power

EXT TRIG -

5 GND

EXTERNAL TRIGGER

Ground

DS1500

Signal

+ 5 V

47 K

40 Vdc max

External Trigger Input Command using External Power

OUTPUT CONNECTIONS

USER INTERFACE

Vext 40 Vdc max.,

20 mA max.

DS1500

7/14

GND Ground

VCE max = 40 Vdc

I max = 20 mA continuous

Connectivity:

RS232 Point-to-point Layout RS485 Point-to-point Layout

Terminal Host

DS1500

Host

DS1500

cMain Serial Interface (RS232) cMain Serial Interface (RS485 Full Duplex)

dAuxiliary Serial Interface (Local Echo) dExternal Trigger (for On-Line Mode)

eExternal Trigger (for On-Line Mode)

RS232 Pass-through Layout

Host

DS1500 2

3 3

DS1500

cMain Serial Interface

dAuxiliary Serial Interface

eExternal Trigger (for On-Line Mode)

DS1500 QUICK GUIDE

Connectivity:

RS232 Master/slave Layout Multiplexer Layout

Host

DS1500

Slave

DS1500

Slave DS1500

Master

Host

MX4000

01 31

cMain Serial Interface cMain Serial Interface

dAuxiliary Serial Interface dExternal Trigger (for On-Line Mode)

eExternal Trigger (for On-Line Mode)

Reading Diagrams:

DS1500-1100

(in)

0 1 32 106(in)

45 7 89

0 20 40 60

80 100 120 140 160 180 200 220 240 260 (mm)

120

100

120

(mm)

0.50 mm

(20 mils)

0.20 mm

(8 mils)

0.15 mm

(6 mils)

0.30 mm

(12 mils)

NOTE: (0,0) is the center of the laser beam output window.

CONDITIONS

Code = Interleaved 2/5 or Code 39

PCS = 0.90

"Pitch" angle = 0°

"Skew" angle = 15°

"Tilt" angle = 0°

*Motor Control = Speed_3 (800 scans/s) for 0.15mm codes, Speed_4 (1200 scans/s) for 0.20mm codes and greater

* Parameter selectable in Winhost

DS1500 QUICK GUIDE

DS1500-2100

0.5

2.5

1.5

2.5

(in)

01 53 (in)

0 10 20 30

40 50 60 70 80 90 100 110 120 130 (mm)

(mm)

0.20 mm

(8 mils)

0.12 mm

(5 mils)

0.10 mm

(4 mils)

0.5 3.5 4.5

1.5 2.5

0.15 mm

(6 mils)

NOTE: (0,0) is the center of the laser beam output window.

CONDITIONS

Code = Interleaved 2/5 or Code 39

PCS = 0.90

"Pitch" angle = 0°

"Skew" angle = 15°

"Tilt" angle = 0°

*Motor Control = Speed_3 (800 scans/s)

• Parameter selectable in Winhost

DS1500 QUICK GUIDE

User Interface:

The following table contains the pinout for standard RS232 PC Host interface. For other user interface types

please refer to their own manual.

RS232 PC-side connections

1 5

9-pin male connector

2514

25-pin male connector

Pin Name Pin Name

2 RX 3 RX

3 TX 2 TX

5 GND 7 GND

7 RTS 4 RTS

8 CTS 5 CTS

How To Build A Simple Interface Test Cable:

The following wiring diagrams show a simple test cable including power, external (push-button) trigger and PC

RS232 COM port connections.

15-pin D-sub HD female

SGND

RXAUX

TXAUX

DS1500 5

GND

9-pin D-sub female

GND

Power Supply

VS (5 Vdc)

Power GND

Trigger

EXT TRIG-

Test Cable for DS1500

NOTE

The Auxiliary RS232 interface is only available when the main interface is RS232.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escáner de Datalogic

Datalogic

Datalogic Magellan 3300HSi Manual de instalación y operación

Datalogic

Datalogic Heron HD3130 Manual de usuario

Datalogic

Datalogic Jade X7 Manual de usuario

Datalogic

Datalogic HS7500 Manual de usuario

Datalogic

Datalogic Magellan 3300HSi Manual de usuario

Datalogic

Datalogic Gryphon I GPS4400 Manual de usuario

Datalogic

Datalogic Magellan 9800i Manual de usuario

Datalogic

Datalogic DLL2020-WO Manual de usuario

Datalogic

Datalogic Magellan 9800i Manual de usuario

Datalogic

Datalogic Matrix 210 Manual de usuario

Datalogic

Datalogic Matrix 450 Manual de usuario

Datalogic

Datalogic Falcon 4410 Manual de instalación y operación

Datalogic

Datalogic CATCHER D531 Series Manual de usuario

Datalogic

Datalogic PWR-480W Manual de usuario

Datalogic

Datalogic Magellan 1500i Manual de instalación y operación

Datalogic

Datalogic AREX Manual de usuario

Datalogic

Datalogic DS6300 Manual de usuario

Datalogic

Datalogic Gryphon GPS4421 Manual de usuario

Datalogic

Datalogic DS1500 Manual de usuario

Datalogic

Datalogic HandScanner MR Manual de usuario

Datalogic

Datalogic Magellan 9800i Manual de instalación y operación

Datalogic

Datalogic STS320 Series Manual de usuario

Datalogic

Datalogic Magellan 3500HSi Manual de usuario

Datalogic

Datalogic TC1200-1 00 Series Manual de usuario

Manuales populares de Escáner de otras marcas

Plustek

Plustek Scanner Manual de usuario

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manual de usuario

Renkforce

Renkforce DS100-5M Manual de usuario

Image Access

Image Access WideTEK A2 Manual de usuario

Canon

Canon imageFORMULA CR-120N Manual de usuario

Fujitsu

Fujitsu FI-4860C2 Manual de usuario

GeoSlam

GeoSlam ZEB Horizon Instrucciones de instalación

Kodak

Kodak i5800 Scanner Manual de usuario

Kodak

Kodak i7300 Manual de usuario

Revopoint

Revopoint POP Manual de usuario

Fujitsu

Fujitsu fi-4860C Manual de usuario

Eddyfi Technologies

Eddyfi Technologies Floormap X Manual de usuario

Faselase

Faselase F6 Manual de usuario

Fujitsu

Fujitsu CardMinder Manual de usuario

Uniden

Uniden BC340CRS Manual de usuario

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manual de usuario

Mustek

Mustek PageExpress 4800 Pro Manual de usuario

Optex

Optex 750830 Manual de usuario