Datalogic MAGELLAN 3200VSI Manual de usuario

MagellanTM 3200VSi

Omni-Directional Imaging Scanner

Quick Reference Guide

Datalogic ADC, Inc.

959 Terry Street

Eugene, OR 97402

USA

Telephone: (541) 683-5700

Fax: (541) 345-7140

procedures described therein may be reproduced or transmitted in any form or by any means

without prior written permission of Datalogic ADC, Inc. or its subsidiaries or affiliates ("Datalogic"

or “Datalogic ADC”). Owners of Datalogic products are hereby granted a non-exclusive, revocable

license to reproduce and transmit this documentation for the purchaser's own internal business

purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices,

contained in this documentation and shall ensure that all notices appear on any reproductions of

the documentation.

Should future revisions of this manual be published, you can acquire printed versions by contact-

ing your Datalogic representative. Electronic versions may either be downloadable from the Data-

logic website (www.datalogic.com) or provided on appropriate media. If you visit our website and

would like to make comments or suggestions about this or other Datalogic publications, please let

us know via the "Contact Datalogic" page.

Disclaimer

Datalogic has taken reasonable measures to provide information in this manual that is complete

and accurate, however, Datalogic reserves the right to change any specification at any time with-

out prior notice.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries,

including the U.S.A. and the E.U. All other brand and product names may be trademarks of their

respective owners.

Magellan is a registered trademark of Datalogic ADC, Inc. in many countries, including the U.S.A.

and the E.U.

Patents

See www.patents.datalogic.com for patent list.

See the Regulatory Addendum included with your product

for additional regulatory, safety and legal information.

Quick Reference Guide 1

Quick Reference

Use this guide to quickly complete your installation and begin using your

scanner. For more details, including programming information, reference

the Product Reference Guide (PRG), which is available for viewing and

download from the Datalogic website listed on the back cover of this

manual.

Nomenclature

1. Back Cover 8. P/N Label

2. Scanner Push Button 9. USB/SD Cover

3. Camera Push Button 10. USB Test Port

4. Scan Window 11.SD Card Slot

5. Cable Connector Cover 12. Host (blue) Port

6. Checkpoint EAS Wire Cavity 13. Auxiliary (yellow) Port for handheld scanner,

etc.

7. Serial Number/Regulatory

Label

813

2 MagellanTM 3200VSi

Installation

Connect the scanner to the host (terminal) using the interface (I/F) cable

as shown below. A cable from an older existing installation can be re-

used if it uses Power Off the Terminal (POT), unless it is a USB POT cable.

If external power is used/needed, plug the AC Adapter into the AC wall

outlet, then connect it to the I/F cable as shown in ‘b’ and ‘c’ of the illus-

tration.

Scan some known-good bar code samples to verify correct operation. The

scanner should beep and/or flash its good read LED1and send the bar

code data to the host or terminal. If not, use the Troubleshooting section

of this guide to identify any problems.

Scanner installation is complete.

1. Be aware that beeper and LED behavior may have previously been config-

ured as “disabled” by another user.

or...

Terminal (PC)

To Terminal (PC)

Other Non-POT Cables

via short adapter cable

Power Off

the Terminal

(POT)

Keyboard Wedge, RS-232

and USB Cables

Keyboard

Wedge

Quick Reference Guide 3

How to Scan

Bar codes can either be presented to the scanner’s window or pushed

past it using a “sweep” technique. The scanner can altenatively be pro-

grammed to initiate a scan of a cell phone or other LCD bar code object, or

an image capture upon pushing the Camera Push Button. See the PRG for

more details.

Troubleshooting

Use this table to resolve common problems.

1. Product 4. Sweeping motion

2. Scan Window 5. Presentation motion

3. Bar code

PROBLEM SOLUTION

Scanner does not power on Exchange the power supply with a known

good power supply and retest operation.

No communication with the host

Consult your technical support personnel

or refer to your host system manual to

verify the proper interface type, cable and

connection port(s) for the scanner. Verify

the interface cable is securely attached to

the host and the scanner.

4 MagellanTM 3200VSi

Productivity Index Reporting™ Option

Your scanner may be equipped with the optional Productivity Index

Reporting™feature. This feature allows for data collection on the readabil-

ity index of bar codes scanned by the scanner. This data may be trans-

mitted to the POS Terminal, where it may be easily sorted for action by

the MIS department to improve bar code quality at the front end.

For additional information on how to enable Productivity Index Reporting

in your scanner, please refer to the Product Reference Guide (PRG)

Scanner Push Button

The Scanner Push Button also performs multiple functions depending

upon the duration of time it is pressed:

The scanner will not read bar codes at

all, or reads poorly

Make sure the window is clean. Check

that the bar codes are of sufficient quality

to be recognized by the scanner. Wrin-

kled, smudged, or torn labels can cause

the scanner to not read at all. Scan

known-good labels of an active symbol-

ogyato check the scanner's read opera-

tion.

If the scanner still does not function properly, consult the Product Reference Guide

(PRG) or contact your local supplier or Datalogic Customer Support Services.

a. Reading of the various bar code symbologies can be independently

enabled or disabled in the scanner.

NOTE

Volume changes made using the Volume/Tone

Push Button are lost when the scanner is pow-

ered down and are reset to the configured set-

ting. If you wish to permanently change the

volume, use the special programming labels in

the Product Reference Guide.

PROBLEM SOLUTION

Quick Reference Guide 5

Table 1. Scanner Push Button Functions

PRESS

DURATION FUNCTION COMMENT

Momentary

(when scanner is

asleep)

Wakes scanner from

Sleep Mode

Alternatively, the scanner can

be awakened by:

- Moving an object through the

scan zone.

- Scanning with an attached

auxiliary scanner.

Momentary

(when scanner is

awake)

Increments volume

Press the push button momen-

tarily to increase speaker vol-

ume. When the loudest volume

is reached, a repeated press of

the push button cycles volume

back to the lowest setting, then

volume increases on subse-

quent press(es). Four volume

levels are available.

Hold, then

release when the

beeper sounds

Increments tone

Press the push button for

approximately 2 seconds, then

release. Each time this is done,

the beeper will sound at one of

three tones. Stop when the

desired tone (high, medium or

low) is sounded.

4 Seconds Scanner Diagnostics

Modea

This mode allows system sup-

port personnel to troubleshoot

problems with the scanner and

is used to determine if it can

read bar codes. Press the but-

ton for 8 seconds or cycle

power to exit Scanner Diagnos-

tics Mode and reset the scan-

ner.

8 Seconds Resets ScannerbOnly system support person-

nel should perform a reset.

a. By standard default, this function is normally disabled to prevent

accidental activation by users.

b. Users should not perform scanner resets except under the direction

of trained systems support personnel.

6 MagellanTM 3200VSi

LED and Beeper Indicators

The scanner’s beeper sounds and its green LED illuminates to indicate

various functions or errors on the scanner. The tables below list these

indications. An exception to the behaviors listed in the tables is that the

scanner’s functions are programmable, and may or may not be turned

on. For example, certain indications, such as the power-up beep can be

disabled using programming bar code labels.

Table 2. Green LED Indications

LED

INDICATION INDICATION COMMENT

Power-on

indication Bright green flash

Indicates the scanner has finished all

its power-up tests and is now ready

for operation.

Good Read

Indication Bright green flash Indicates a bar code has been read

and decoded.

Scanner

Ready Constant dim green The scanner is ready for operation.

Sleep Mode

Green LED slowly

and continuously

changes from off to

dim to off.

The scanner is in Sleep Mode. To

wake the scanner up, move an object

in front of its window or press the

button atop the unit. This indication

is optionally configurable, and may

have been programmed to behave

differently.

Host Disable

Constant green

flash at 1 Hz

(100mS on, 900mS

off)

The scanner is disabled due to receiv-

ing a disable command from the POS

terminal.

Diagnostics

Varies (see Error

Codes on page 8

for more informa-

tion)

The LED can provide diagnostic feed-

back if the scanner discovers a prob-

lem during SelfTest.

Prog. Mode See Host Disable

above.

The scanner is in Programming

Mode.

Quick Reference Guide 7

Table 3. Beeper Functions

BEEPER

INDICATION INDICATION COMMENT

Power On

Beep Single beep

The Power-On LED indication is a con-

figurable feature which can be enabled

or disabled. When enabled, this beep

indicates the scanner has finished all

its power-up tests and is now ready for

operation.

Good Read

Indication Single beep

The good read beep indication is config-

urable. Options include: Enable/dis-

able, frequency, duration and volume.

See the Product Reference Guide (PRG)

for more information.

Diagnostics

Varies (see Error

Codes on page 8

for more infor-

mation)

The Beeper can provide diagnostic

feedback if the scanner discovers a

problem during SelfTest.

Programming

Mode

Indications

Varies depend-

ing upon the fea-

ture(s) being

configured.

The Beeper will sound as programming

bar code labels are scanned, indicating

progress during scanner configuration.

8 MagellanTM 3200VSi

Error Codes

If an error is detected, the scanner will sound a long low tone (for three

seconds) and flash its LED, indicating a failure. When this occurs, press

the Scanner Push button to hear the error code. If it is configured to do

so, the scanner will sound a series of beeps corresponding to the error

code and/or flash its LED simultaneous to the beeps. The table below

describes what these codes mean and what action should be taken for

each.

NUMBER OF

LED FLASHES/

BEEPS

ERROR CORRECTIVE ACTION

1Configuration

Contact Helpdesk for

assistance

2Interface PCB

4Imager

6Main PCB

10 Button Error

11 Hardware ID

12 Model ID

13 CPLD ID

Otros manuales para MAGELLAN 3200VSI

Tabla de contenidos

Otros manuales de Lector de código de barras de Datalogic

Datalogic

Datalogic DX8200A Manual de usuario

Datalogic

Datalogic Reader Matrix-1000 Manual de usuario

Datalogic

Datalogic GRYPHON M SERIES Manual de usuario

Datalogic

Datalogic DS6300 Manual de usuario

Datalogic

Datalogic DS6400 Manual de usuario

Datalogic

Datalogic MAGELLAN 3200VSI Manual de usuario

Datalogic

Datalogic Gryphon GFE4400 Guía de configuración rápida

Datalogic

Datalogic Gryphon I GM440 Series Manual de instalación y operación

Datalogic

Datalogic PowerScan PD9530 Manual de instalación y operación

Datalogic

Datalogic MAGELLAN 3200VSI Manual de usuario

Datalogic

Datalogic GRYPHON BT Series Manual de usuario

Datalogic

Datalogic Magellan 1100i Manual de usuario

Datalogic

Datalogic Hand-Held Devices II Hoja de instrucciones

Datalogic

Datalogic PowerScan Retail PBT9501-RT Manual de usuario

Datalogic

Datalogic Gryphon I GBT4500 Manual de usuario

Datalogic

Datalogic Gryphon GD4130 Manual de usuario

Datalogic

Datalogic PowerScan D8300 Manual de usuario

Datalogic

Datalogic matrix 450N Manual de usuario

Datalogic

Datalogic DH60 Manual de usuario

Datalogic

Datalogic Gryphon I GBT4100 Manual de usuario

Datalogic

Datalogic AccuLazr AL5010 Manual de usuario

Datalogic

Datalogic Magellan 9300i Manual de usuario

Datalogic

Datalogic PowerScan M8500 Manual de instalación y operación

Datalogic

Datalogic QuickScan I QM21X1 Manual de instalación y operación

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario

Atid

Atid AT188N Plus Manual de usuario