Datalogic Arex 420 Manual de usuario

Datalogic Lighter built-in ProfiNet I/O

for Laser Marking Systems

Installation and User Manual

April 2019

REVISION 1.0

Department

TSS L3 LM

Classification

Public

Page 2 18/04/2019

Version

1.0

Date

4/18/2019

Page 2/27

Master Revision History

Revision

Date

Author(s)

Change Description

1.0

18.04.2019

M. Pierpaolini

Beta Site Release

Department

TSS L3 LM

Classification

Public

Page 3 18/04/2019

Version

1.0

Date

4/18/2019

Page 3/27

INDEX

INTRODUCTION TO THIS USER MANUAL ......................................................................... 41.

SETUP OVER PROFINET/IO NETWORK .............................................................................. 52.

2.1. CONFIGURING THE LASER MARKER FOR USE OVER PNIO............................................................ 5

Basic net settings of the Laser Marker ........................................................................... 5

Advanced net settings of the Laser Marker .................................................................... 7

2.2. CONFIGURING THE SIEMENS™S7-1200 CONTROLLER FOR USE OVER PNIO ............................... 13

Creating a PNIO node using the GSDML file ................................................................. 13

Configuring the Laser Marker PNIO node on TIA Portal................................................ 15

CYCLIC COMMUNICATION BETWEEN THE PLC AND THE DATALOGIC LASER MARKING3.

SYSTEM........................................................................................................................... 16

3.1. INPUT ASSEMBLY MEMORY MAP ........................................................................................ 18

Description of the Input Assembly Memory Map.......................................................... 19

3.2. OUTPUT ASSEMBLY MEMORY MAP ..................................................................................... 20

Description of the Output Assembly Memory Map ....................................................... 21

3.3. POSSIBLE ERRORS .......................................................................................................... 23

Command Error ........................................................................................................... 23

Protocol Error .............................................................................................................. 24

TROUBLESHOOTING..................................................................................................... 264.

Department

TSS L3 LM

Classification

Public

Page 4 18/04/2019

Version

1.0

Date

4/18/2019

Page 4/27

Introduction to this User Manual1.

This User manual has been developed for PLC programmers who intend to connect a

Datalogic Laser Marker to a PLC via ProfiNet/IO, in order to handle the Laser Marker and

its operations following the flow of the Production Chain.

All the screenshots and tests made as a reference for the creation of this User Manual

were made using the following versions of HW and SW:

Element used

Versioning

PLC

Siemens S7-1200

CPU 1214C DC/DC/DC

Article no. 6ES7 214-1AG31-0XB0

Firmware rev. 3.0

PLC programming SW tool

TIA Portal v.13 SP1

Datalogic Laser Marker

Arex430

Lighter version

Lighter 7.2.0 Alpha 8

Datalogic S.r.l. recommends to read this User Manual carefully before

performing any kind of operation both on the PLC and the Laser Marker. I case of any

doubts, please contact your local Datalogic Technical Support or fill in the Support

Webform on the Datalogic s.r.l website at the following link.

Department

TSS L3 LM

Classification

Public

Page 5 18/04/2019

Version

1.0

Date

4/18/2019

Page 5/27

Setup over ProfiNet/IO Network2.

In order to have ProfiNet/IO connection between the PLC and the Datalogic Laser

Marker, it is necessary to set up both elements: this chapter want to show the necessary

steps and the choices which the PLC programmer can make according to his needs, in

order to have communication between these two ProfiNet/IO devices.

2.1. Configuring the Laser Marker for use over PNIO

Some operations must be made on the Laser in order to have it working on an

Profinet/IO network; PLC programmers will need to assign on each Laser Marking a

Device Name and make changes to the Firewall Rules: moreover, the User, according to

his application will have to choose the dimension of the Input and Output Memory

Areas. These changes are described in the following paragraphs.

Basic net settings of the Laser Marker

The Datalogic Laser Marking systems can be discovered on an ProfiNet/IO network only

if a number of parameters on the Laser Marker and on the PLC match. The parameters

which should match are the following:

-Device Name;

-Size of Input and Output memory maps.

The Device Name of the Laser Marker can be changed following these steps:

a) Open the ‘Laser Configuration’on the Laser Marking System, by right-clicking

the Laser Engine icon in the Windows tray bar.

b) Once the Laser Configurator is open, select the ‘Network’ voice of the menu from

the left side of the interface and the Device Name can be found under the voice

‘Device Network Name’.

Department

TSS L3 LM

Classification

Public

Page 6 18/04/2019

Version

1.0

Date

4/18/2019

Page 6/27

c) The size of the Input and Output Memory Maps has to be set also inside the

‘Profinet’section, choosing from the 3 possible sizes expressed in Bytes (64,

128 or 254).

d) Once these parameters have been set, press ‘Apply’ followed by ‘OK’ on the

bottom of the Interface.

Department

TSS L3 LM

Classification

Public

Page 7 18/04/2019

Version

1.0

Date

4/18/2019

Page 7/27

Advanced net settings of the Laser Marker

All Datalogic Laser Marking devices are controlled by the Windows Firewall, which by

default settings does not allow Inbound and Outbound ProfiNet/IO traffic; in order to

establish a ProfiNet/IO connection between the PLC and the Laser Marker, the user can

either completely disable the control of the Windows Firewall, or allow all Inbound and

Outbound traffic regarding ‘LaserEngine.exe’.

To create these Inbound and outbound rules regarding the Windows Firewall, the User

can follow this procedure on the Laser Marker:

1. Enter the Control Panel and select ‘Advanced settings’.

2. New Inbound and Outbound rules need to be set for the ‘LaserEngine.exe’

program: click on ‘Inbound Rule’ and then select ‘New Rule…’.

Department

TSS L3 LM

Classification

Public

Page 8 18/04/2019

Version

1.0

Date

4/18/2019

Page 8/27

3. A Wizard GUI will guide you through the procedure: select ‘Program’.

4. In the Program And Services tab, browse towards the ‘LaserEngine.exe’

application, present in

C:\ProgramFiles\Lighter\7.2

Department

TSS L3 LM

Classification

Public

Page 9 18/04/2019

Version

1.0

Date

4/18/2019

Page 9/27

5. Select ‘Allow the connection’, then press ‘Next’.

Department

TSS L3 LM

Classification

Public

Page 10 18/04/2019

Version

1.0

Date

4/18/2019

Page 10/27

6. Select all 3 types of Network.

7. Give this property a recognizable name.

Tabla de contenidos

Otros manuales de Lector de código de barras de Datalogic

Datalogic

Datalogic TC1100 Manual de usuario

Datalogic

Datalogic DS2100 Manual de usuario

Datalogic

Datalogic Gryphon I CHR-GM40 Manual de usuario

Datalogic

Datalogic QuickScan Lite QW2100 Manual de usuario

Datalogic

Datalogic PowerScan PM9500-RT Manual de usuario

Datalogic

Datalogic QuickScan QS2500 Manual de usuario

Datalogic

Datalogic MAGELLAN 3200VSI Manual de instalación y operación

Datalogic

Datalogic Matrix-1021 HD Manual de usuario

Datalogic

Datalogic Magellan 3300HSi Manual de usuario

Datalogic

Datalogic QuickScan QS6500 Manual de instalación y operación

Datalogic

Datalogic Heron HD3100 Manual de instalación y operación

Datalogic

Datalogic QuickScan i Manual de instalación y operación

Datalogic

Datalogic DS6300 Manual

Datalogic

Datalogic QuickScan QD2590 Manual de usuario

Datalogic

Datalogic Gryphon D432E Manual de usuario

Datalogic

Datalogic Gryphon GD4130 Manual de usuario

Datalogic

Datalogic DS8100 Manual de usuario

Datalogic

Datalogic Gryphon I GD44XX Manual de instalación y operación

Datalogic

Datalogic DS8100 Manual de usuario

Datalogic

Datalogic PowerScan PD8530 Manual de usuario

Datalogic

Datalogic FireScan D111 Series Manual de usuario

Datalogic

Datalogic Quickscan I Manual de usuario

Datalogic

Datalogic Gryphon D100 Manual de usuario

Datalogic

Datalogic Magellan 800i Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario

Atid

Atid AT188N Plus Manual de usuario