Data Video WM-11 Manual de usuario
WM-11
2
Table of Contents
WARRANTY ................................................................................................... 3
STANDARD WARRANTY .......................................................................................3
THREE YEAR WARRANTY .....................................................................................4
DISPOSAL ......................................................................................................4
INTRODUCTION.............................................................................................5
PARTS ASSEMBLY AND INSTALLATION ..........................................................5
PRE-WORK ........................................................................................................5
PROCEDURE.......................................................................................................6
INSTALLING PTR-10/10T.............................................................................. 11
INSTALLING PTC-150 ................................................................................... 13
FREQUENTLY ASKED QUESTIONS................................................................. 15
DIMENSIONS AND WEIGHT ......................................................................... 16
SPECIFICATIONS .......................................................................................... 17
SERVICE AND SUPPORT ............................................................................... 20
Disclaimer of Product & Services
The information offered in this instruction manual is intended as a guide only.
At all times, Datavideo Technologies will try to give correct, complete and
suitable information. However, Datavideo Technologies cannot exclude that
some information in this manual, from time to time, may not be correct or
may be incomplete. This manual may contain typing errors, omissions or
incorrect information. Datavideo Technologies always recommend that you
double check the information in this document for accuracy before making
any purchase decision or using the product. Datavideo Technologies is not
responsible for any omissions or errors, or for any subsequent loss or damage
caused by using the information contained within this manual. Further advice
on the content of this manual or on the product can be obtained by
contacting your local Datavideo Office or dealer.
3
Warranty
Standard Warranty
Datavideo equipment is guaranteed against any manufacturing defects for
one year from the date of purchase.
The original purchase invoice or other documentary evidence should be
supplied at the time of any request for repair under warranty.
The product warranty period beings on the purchase date. If the purchase
date is unknown, the product warranty period begins on the thirtieth day
after shipment from a Datavideo office.
All non-Datavideo manufactured products (product without Datavideo
logo) have only one year warranty from the date of purchase.
Damage caused by accident, misuse, unauthorized repairs, sand, grit or
water is not covered under warranty.
Viruses and malware infections on the computer systems are not covered
under warranty.
Any errors that are caused by unauthorized third-party software
installations, which are not required by our computer systems, are not
covered under warranty.
All mail or transportation costs including insurance are at the expense of
the owner.
All other claims of any nature are not covered.
All accessories including headphones, cables, batteries, metal parts,
housing, cable reel and consumable parts are not covered under warranty.
Warranty only valid in the country or region of purchase.
Your statutory rights are not affected.
4
Three Year Warranty
All Datavideo products purchased after July 1st, 2017
qualify for a free two years extension to the standard
warranty, providing the product is registered with
Datavideo within 30 days of purchase.
Certain parts with limited lifetime expectancy such as LCD panels, DVD
drives, Hard Drive, Solid State Drive, SD Card, USB Thumb Drive, Lighting,
Non-PCIe Card and third party provided PC components are covered for 1
year.
The three-year warranty must be registered on Datavideo's official website
or with your local Datavideo office or one of its authorized distributors
within 30 days of purchase.
Disposal
For EU Customers only - WEEE Marking
This symbol on the product or on its packaging indicates that
this product must not be disposed of with your other
household waste. Instead, it is your responsibility to dispose of
your waste equipment by handing it over to a designated
collection point for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment at the time of
disposal will help to conserve natural resources and ensure that it is recycled
in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
CE Marking is the symbol as shown on the left of this page.
The letters "CE" are the abbreviation of French phrase
"Conformité Européene" which literally means "European
Conformity". The term initially used was "EC Mark" and it was officially
replaced by "CE Marking" in the Directive 93/68/EEC in 1993. "CE Marking" is
now used in all EU official documents.
5
Introduction
WM-11 Professional Wall Mount is designed specifically for Datavideo
PTR-10/10T Robotic Pan Tilt Head as well as the PTZ camera series
(PTC-150/150T/200/200T). The two bubble level meters allow the user
to align the mounted device horizontally.
The four piece mounting kit is made of rugged metal and is easy to
install on any walls in either an upright or upside down position. The
assembled mount can support up to a 10 Kg load.
Note: WM-11 is designed for PTR series of robotic pan tilt heads and
PTC series of PTZ cameras.
Parts Assembly and Installation
In this section, you will be shown how you can assemble and install
your kit.
Pre-work
1. First check you have all the parts listed in the table below.
No.
Part Names
Qty
1
Wall plate
1
2
Left bracket
1
3
Right bracket
1
4
Round rod
1
5
Base plate
1
6
M5x20 nickel plated hex socket cap screw
12
7
Expansion bolt
4
8
Bubble level meter
3
9
M2.5 screw
6
10
M3 x 10mm screw and spring washer
4
11
M3 x 8mm screw
4
6
2. On the surface where the WM-11 is to be mounted, drill four holes
spaced according to the dimensions indicated in the diagram below.
Then follow the procedure in the next section to assemble and install
the WM-11.
Procedure
The diagram below is an exploded-view drawing of WM-11, and the
numbers correspond to the respective installation steps.
1
2
3
4
5
Bubble Level
Meter
7
1. First mount a bubble level meter to the wall plate using two M2.5
screws. Align the wall plate with the four holes drilled in Pre-Work
then use four expansion bolts to secure the wall plate. See the
diagram below.
Please note that you can use the bubble level meter to make sure
that the wall plate is properly aligned. If the bubble is at the center,
the wall plate is horizontally aligned (perfectly levelled). If the bubble
is on either side, the wall plate is tilted to the sides.
8
2. Assemble the left bracket to the wall plate with two M5x20 nickel
plated hex socket cap screws as shown in the diagram below.
3. Assemble the right bracket to the wall plate with two M5x20 nickel
plated hex socket cap screws as shown in the diagram below.
9
4. Place the round rod in between the left and right brackets then
secure it in position by fastening two M5x20 nickel plated hex
socket cap screws to the respective holes on the brackets as
shown in the diagram below.
5. Use four M2.5 screws to mount two bubble level meters to the
base plate with one in the front and one at the bottom.
Insert the base plate between the left and right brackets then
secure it in position by fastening six M5x20 nickel plated hex
socket cap screws to the respective holes on the brackets as
shown in the diagram below. By inspecting the bubble level meter,
10
you can make sure the base plate is properly aligned, i.e. the
bubble is at the center. The inner rails on the right and left
brackets should allow you to move the base plate back and forth.
Note: The base plate may be inserted in an upright or upside
down position.
Tabla de contenidos
Otros manuales de Rack y soporte de Data Video
Data Video
Data Video RMK-2 Manual de usuario
Data Video
Data Video RP-55 Manual de usuario
Data Video
Data Video LBK-2 Manual de usuario
Data Video
Data Video RKM-572 Manual de usuario
Data Video
Data Video PTR-10 Manual de usuario
Data Video
Data Video WM-10 Manual de usuario
Data Video
Data Video WM-1 Series Manual de usuario
Data Video
Data Video CM-10 Manual de usuario
Data Video
Data Video TTL-100 Manual de usuario
Data Video
Data Video RMK-1 Manual de usuario
