Dantel 05202 Manual de usuario
CAUTION
•Install or remove modules from the shelf only when the power is off.
If you install a module in the shelf with the power on, the internal
circuitry may suffer damage and the product warranty will be void.
•Remove and install circuit boards only in a static-safe environment
(use antistatic wrist straps, smocks, footwear, etc.).
•Keep circuit boards in their antistatic bags when they are not in use.
•Do not ship or store circuit boards near strong electrostatic, electromag-
netic, magnetic, or radioactive fields.
•For more complete information on electrostatic discharge safety
precautions, refer to BellcoreTM Technical Reference # TR-NWT-000870.
Copyright 1999 by Dantel, Inc. • Dantel is a registered trademark of Dantel, Inc. • ISO 9001 Registered
Printed in the U.S.A.
INSTALLATION & OPERATION MANUAL
05202-0299 <90-00046>
05202
SMALL CENTRAL OFFICE
MASTER ALARM SYSTEM
About this Practice:
This practice has been reissued to:
• Update to reflect Y2K compliance.
Issue date: February 1999
Reissued Practices: Updated and
new content can be identified by a
banner in the right margin.
UPDATED
Table of Contents
Ordering Information ........................................................................... 2
Introduction .......................................................................................... 3
Application Information ....................................................................... 5
Installation............................................................................................ 7
Support Documentation ..................................................................... 43
Warranty ............................................................................................. 46
PAGE 2 05202-0299 <90-00046>
ORDERING INFORMATION
The DJ05202 drawings provide information for ordering the
various components of the Small Central Office Master
Assembly. All the above options include a 256K Status Monitor
w/ keyboard, 41071 Alarm Display Unit, and 3 Terminal Block
Assemblies.
NOTE: This section lists the different options available for this product. To order any of the avail-
able options, contact Dantel Inside Sales through our toll-free number, 1-800-432-6835.
OPTION NUMBER FEATURES
A18-05202-30 256 Discrete Alarm Points, 16 Control Points, 15 TBOS Ports, Writing Shelf
A18-05202-31 128 Discrete Alarm Points, 16 Control Points, 15 TBOS Ports, Writing Shelf
A18-05202-32 128 Discrete Alarm Points, 16 Control Points, 7 TBOS Ports, Writing Shelf
A18-05202-33 96 Discrete Alarm Points, 16 Control Points, 7 TBOS Ports, Writing Shelf
A18-05202-34 160 Discrete Alarm Points, 16 Control Points, 7 TBOS Ports, Writing Shelf
A18-05202-35 256 Discrete Alarm Points, 16 Control Points, 15 TBOS Ports
05202-0299 <90-00046> PAGE 3
INTRODUCTION
This system manual provides information on how to order,
install, and operate the Small Central Office Master Alarm
Assembly. The manual is divided into three main sections, as
outlined below.
Application
A brief description is provided of how the shelf operates and
interfaces with external equipment.
Installation
Follow this section for step-by-step details on installing the
equipment. This section is divided into five parts: equipment
mounting, wiring, switch and strap settings for modules,
turn-up procedure and troubleshooting. The turn-up procedure
provides instructions for getting the system operating.
Support Documentation
This section consists of individual practices on the different
components of the system. The practices provide in-depth
information on the operation of the system components, func-
tional schematics, and technical specifications. The operating
instructions in the practices will provide a useful reference to
the user who needs more details than given in the turn-up
procedure in the Installation section.
PAGE 4 05202-0299 <90-00046>
INTRODUCTION
05202-0299 <90-00046> PAGE 5
APPLICATION INFORMATION
For a functional schematic of the Small Central Office Master
Alarm System Shelf, refer to sheet 2 of the DJ05202 drawing
that follows this page.
Operation of the shelf is controlled by 46020 Multiple Alarm
Processor (MAP) in slot 12. The MAP polls for alarms and issues
commands to operate control points through the Smart MACs in
slots 10 and 11. The 46009 Multiple Alarm Transmitters (MATs)
in slots 1 through 8 accept ground inputs. The 46028 Control
Point Module (CPM) in slot 9 has normally-open relays for
operating controls.
Alarms received by the MAP are reported locally to the 46001
Status Monitor and 41071 Alarm Display Unit.
The MAP also communicates with the alarm center through the
44124 Data Station Termination module is slot 13.
The MAP and Status Monitor require a database to operate.
These databases are configured using a computer running
T/Shell software and downloaded to the modules from the
computer.
The Fuse Module provides fused power to each slot of the shelf.
PAGE 6 05202-0299 <90-00046>
APPLICATION INFORMATION
05202-0299 <90-00046> PAGE 7
INSTALLATION
This section consists of five parts, as explained below.
EQUIPMENT MOUNTING
♦41060 Writing Shelf
♦41071 Alarm Display Unit
♦46001 Status Monitor
♦05202 Equipment Shelf
WIRING
♦A18-05202-XX Block Diagram
♦DT-05202-30 Master Alarm System Interconnection draw-
ings
SWITCH AND STRAP SETTINGS
♦44124-00 Data Channel Termination Module
♦46001-03 Status Monitor
♦46009-02 Multiple Alarm Transmitter
♦46020-41 Multiple Alarm Processor
NOTE: This shelf is Y2K compliant if it is equipped with a
D11-46020-41 or later Multiple Alarm Processor
♦46023-14 Smart Multiple Alarm Combiner
♦46028-01 Control Point Module
♦49008-00 Current Loop Subassembly
♦49013-00 Tone Modem Subassembly
TURN-UP PROCEDURE
TROUBLESHOOTING
UPDATED
PAGE 8 05202-0299 <90-00046>
INSTALLATION
05202-0299 <90-00046> PAGE 9
EQUIPMENT MOUNTING
41060 WRITING SHELF
Tools Required
♦Phillips Screwdriver
1. The 41060 can be mounted three ways. Refer to Fig. 1. For maxi-
mum stability, the double mounted projection is recommended.
Units come with brackets in the flush mount position. Additional
brackets are included for double mounting.
2. If not mounting flush, remove the slides from the shelf to reposition
the brackets. Fully extend the slide to access the slide mounting
screws from the outside of the shelf. Remove the front bracket
mounting screws by lining them up with the holes in the slide.
Make sure that the bracket positions match the rack before reat-
taching the slides to the shelf.
FIG. 1 - MOUNTING CONFIGURATIONS, 41060 WRITING SHELF
DOUBLE MOUNTED
PROJECTION
(Recommended)
FLUSH MOUNTED
SINGLE MOUNTED
PROJECTION
INSTALLATION
PAGE 10 05202-0299 <90-00046>
41071 ALARM DISPLAY UNIT
1. Mount the light display box using the two mounting holes on the
rear or left side. Use #6 hardware (not provided).
2. Remove the cover from the remote switch unit and mount as re-
quired using the two mounting holes on the rear. Use #6 hardware
(not provided).
3. Refer to the 41071 practice for information on wiring this unit.
46001 STATUS MONITOR
1. Verify that the equipment rack has at least 8 3/4 inches of vertical
clearance (five rack units) to mount the 46001. Mount the 46001 by
placing it in position in the equipment rack and then installing the
bolts shipped with the unit. If extension brackets were ordered,
they must be installed on the equipment rack prior to mounting the
Status Monitor. Refer to Fig. 2.
2. Mount the brackets to the equipment rack using the slotted holes,
with the base located away from the Status Monitor. Mount the
Status Monitor to the brackets using the threaded holes.
3. Install the ESD studs.
FIG. 2 - MOUNTING BRACKET, 46001 STATUS MONITOR
TOP VIEW
19" STATUS MONITOR
SLOTTED
HOLE
SLOTTED
HOLE
EQUIPMENT RACK
MOUNTING BRACKET
THREADED FLANGE
HOLES
EQUIPMENT RACK
MOUNTING BRACKET
THREADED FLANGE
HOLES
EQUIPMENT RACK
MOUNTING BRACKET
THREADED FLANGE
HOLES
SLOTTED
HOLE
EQUIPMENT RACK
MOUNTING BRACKET
THREADED FLANGE
HOLES
SLOTTED
HOLE
SLOTTED
HOLE
SLOTTED
HOLE
SLOTTED
HOLE
SLOTTED
HOLE
THREADED FLANGE
HOLES
SLOTTED
HOLE
TOP VIEW
23" STATUS MONITOR
INSTALLATION
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Sistema de seguridad de Dantel
Dantel
Dantel 46022-12 Manual de usuario
Dantel
Dantel A23-41073-00 Manual de usuario
Dantel
Dantel B23-41070 Manual de usuario
Dantel
Dantel B15-00459-02 Manual de usuario
Dantel
Dantel A23-41073 Manual de usuario
Dantel
Dantel RemoteMaster 46132-41 Manual de usuario
Dantel
Dantel A18-05791 Series Manual de usuario
Dantel
Dantel B18-05725-03 Manual de usuario
Dantel
Dantel A18-05775 Series Manual de usuario
Dantel
Dantel B23-41071 Manual de usuario
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario