Danfoss 102E7 Manual de usuario
Installation and User Guide
Danfoss Heating
102E7
7-Day electronic mini-programmer
for controlling hot water and heating
(Including Factory Replacement Units FRU)
2
INDEX
Index
Installation
Product specication 3
Installation 4-6
Wiring 6-9
Replacement 10-11
User
Your programmer 12
Resetting the unit 12
24hr or AM/PM display 13
Setting the Time and Day 13
Factory preset programmes 14
Changing the preset programmes 15
Setting the programme - 7 day 16-17
Setting the programme - 5/2 day 18-19
Running your programme 20
Temporary user overrides 21
Battery backup 22
Contact details 24
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other printed
material. All trademarks in this material are property of the respective companies. Danfoss and the
Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
®
Certification Mark
3
Please Note:
This product should only be installed by a qualied electrician
or competent heating installer, and should be in accordance
with the current edition of the IEEE wiring regulations.
Specication
Power supply 230 Vac ± 15%, 50 Hz
Switching action 1 x SPST, Type 1B
Max. Switch rating 264Vac, 50/60Hz, 3(1)A
Running/Setting Accuracy ±1 min./month
Power Reserve Minimum 24 hours
Max. Ambient Temperature 45°C
Dimensions, mm (W, H, D) 102 x 136 x 47
Design standard EN 60730-2-7
Control Pollution Situation Degree 2
Rated Impulse Voltage 2.5kV
Ball Pressure Test 75°C
Product specication
Specication
Installation Instructions
4
Installation
NB. For FRU units - go straight to point 6 below.
1. Loosen the xing screw in the base of the unit to release the
Wiring Cover.
2. Holding the unit face downwards, press rmly in the
centre of the wallplate and slide it apart and lift it from the
module.
3. Fix the wallplate and terminal block to the wall, or plaster
box, as required. Ensure that the screw heads do not
protrude beyond the vertical centre rib of the wallplate,
or this will prevent the module correctly locating onto the
wallplate.
4. Surface cables can only enter from below the unit. Cut
an appropriate cable aperture in the wiring cover. If the
wallplate is mounted on a plaster box, cables can enter
from the rear below the terminal block.
Installation
Screw xing holes
(screwheads MUST
NOT protrude above
centre rib) Vertical centre rib
Wallplate & Terminals
5
5. Electrical connections are simplied by using a Wiring
Centre. However, if this is not used, the wallplate terminal
identication is as shown.
If the system being controlled is 230Vac then terminals
3 and L must be linked with insulated cable capable
of carrying full load current. Whilst the unit does not
require an earth connection, a terminal is provided on the
wallplate for earth continuity purposes.
6. Referring to the wiring diagrams on page 6-9, connect the
unit as shown.
7. Find out from the user whether the unit is required to
operate in 7-day mode (factory preset) or weekday/
weekend mode (5/2 day). To convert to 5/2 day mode
remove the small two-way connector from the pins
towards the left of the recess on the rear of the module,
then press the button marked R/S under the ap to RESET
the unit.
8. Ensure all dust and debris are cleared from the area. Plug
the module into the wallplate by locating it onto the
wallplate and, when ush with it, sliding it down, ensure
the hook at the top of the wallplate engages with the slot
at the back of the module.
9. Before setting the programme, check the unit and circuit. Set
the rocker switch to WATER & HEATING. Press the SELECT
button until the bar in the display lines up with the word ON.
Adjust the remote thermostats to check the system operates
correctly.
Installation
Water Heating
COM
Mains Supply
(via 3 amp fuse)
ON ON NL
123 5 6
6
102, 102E5, 102E7
Wiring
Wiring
10. Then press the SELECT button until the bar lines up with
the word OFF and check the system does not operate.
11. Set the rocker switch to WATER ONLY. Press the SELECT
button until the bar in the display lines up with the word
ON and check that the water circuit only operates.
12. When the circuit check has been completed, replace the
wiring cover and tighten the xing screw. Cut any cable
aperture in the wiring cover which may be necessary to
accommodate surface mounted cables.
13. Finally set time of day and programmes required, noting
that the unit is supplied with a pre-set programme, as
stated on Page 14.
7
Wiring
12356
L N L N
L
N
MAINS
SUPPLY
FUSED
3 AMP
ROOM
' S TAT
LINK
COM
CALL N
PUMP
TERMINALS
BOILER
TERMINALS
102E5
TERMINALS
Typical Gravity DHW with Pumped Heating
Typical domestic gas or oil-red central heating system with
gravity hot water and pumped heating. (If a room thermostat
is not used, wire pump live directly to terminal 2 of the 102E7).
102E7
TERMINALS
8
12356
L N
L
N
MAINS
SUPPLY
FUSED
3 AMP
ROOM
' S TAT
LINK
COM
CALL N
BOILER &
PUMP
TERMINALS
102E5
TERMINALS
MID-POSITION VALVE
BLUE GREY
SAT
WHITE
OR
BROWN
CALL
COM
CYL.
' S TAT
RED OR
ORANGE
Wiring
Typical Heating and Hot Water control system
using 3-port mid-position valve
The above control system is available as the Danfoss Randall
102E7 HEATSHARE pack, which also includes the RMT room
thermostat, AT cylinder thermostat, HS3 mid-position valve
and a WB12 wiring box.
102E7
TERMINALS
9
12356
102E5
TERMINALS
L N
BOILER &
PUMP
TERMINALS
L
N
MAINS
SUPPLY
FUSED
3 AMP
LINK
COM
CALL
N
N
COM
CYL.
' S TAT
CALL
N
SAT
ROOM
' S TAT
HEATING
VALVE
D.H.W
VALVE
Wiring
Typical Heating and Hot Water control system
using 2-port zone valves
The above control system is available as the Danfoss Randall
102E7 HEATPLAN pack, which also includes the RMT room
thermostat, AT cylinder thermostat, two 22mm HPP zone
valves and a WB12 wiring box.
102E7
TERMINALS
10
DANFOSS RANDALL
102E7 Water
ON
Heating
ON COM MAINS SUPPLY
(via 3 amp fuse)
An additional terminal block is
required where these disconnected
leads (or pairs of leads) should be
terminated
1 2 3 5 (N) 6 (L) A B C
RANDALL 102, 102E,
102E7 123 56
RANDALL 3020P, 3060 4 2 - 1,7 6 3 5
RANDALL MKII R6 4 5 - 3 1,2 6 7
HORSTMANN
CORAL 423 & 424
Boiler
(8)
Air ‘Stat
(8) - 2,3 1 4,7 5 6
HORSTMANN
DIAMOND 423 2 4 - N L,1,3 5 6
HORSTMANN
DIAMOND 424 2 4 - N L,1,3 5 6
POTTERTON 423 2 4 - N L,1,3 5 6
SANGAMO S409 F1 & F4 2 5 - N,1,3 L 4,6
SANGAMO (Early model)
S410 Form 4 1,3 4 - N,2 L
Replacement
Otros manuales para 102E7
1
Tabla de contenidos
Otros manuales de Mando a distancia de Danfoss
Danfoss
Danfoss 103E7 Instrucciones de montaje
Danfoss
Danfoss CF-RC Manual de usuario
Danfoss
Danfoss R13 F Manual de usuario
Danfoss
Danfoss FP975 Instrucciones de montaje
Danfoss
Danfoss 175G9004 Manual de usuario
Danfoss
Danfoss MPCAN Manual de usuario
Danfoss
Danfoss IKP1000 Manual de usuario
Danfoss
Danfoss T70 1 HALL Manual de usuario
Danfoss
Danfoss IK2 Manual de usuario
Danfoss
Danfoss IKORE B Manual de usuario
Danfoss
Danfoss SET3M Manual de usuario
Danfoss
Danfoss R06 Manual de usuario
Danfoss
Danfoss CF-RC Manual de usuario
Danfoss
Danfoss Ikargo2 Manual de usuario
Danfoss
Danfoss IKORE Manual de usuario
Danfoss
Danfoss WS103 Manual de usuario
Danfoss
Danfoss Ikompact Manual de usuario
Danfoss
Danfoss CF-RC Manual de usuario
Danfoss
Danfoss TM70 Manual de usuario
Danfoss
Danfoss MP08A Manual de usuario
