Danfoss VLT MCD 200 Manual de usuario
Installation Guide
PROFINET Module
VLT® Compact Starter MCD 200 and VLT® Soft Starter MCD 500
1
1.1
1.2
2
2.1
2.2
2.3
2.4
3
3.1
4
4.1
4.2
4.2.1
4.2.2
4.2.3
4.3
4.4
5
5.1
5.1.1
5.2
5.2.1
5.2.2
5.2.2.1
5.2.2.2
5.2.3
5.2.3.1
5.2.3.2
6
6.1
6.2
6.3
6.4
Contents
Safety 5
Disclaimer 5
Warnings 5
Introduction 6
Product Design 6
Compatibility 6
Product Versions 6
Network Connection 6
Installation 8
Installing the Communication Module 8
Connection 10
Soft Starter Connection 10
Network Connection 10
Ethernet Ports 10
Cables 10
EMC Precautions 11
Network Establishment 11
Addressing 11
Device Configuration 12
Configuration of Device Name 12
Identifying the Device with Ethernet Device Configuration Tool 12
On-board Web Server 13
Connect to the Device 13
Manage Users and Passwords 14
Adding a User 15
Deleting a User 15
Configure IoT Settings 15
Configuring MQTT Settings 16
Configuring OPC UA Settings 17
Operation 18
Requirements for Successful Operation 18
Device Classification 18
Master Configuration 18
Enabling Network Control 18
AN428735951761en-000101/175R1188 | 3Danfoss A/S © 2022.11
Contents
PROFINET Module
Installation Guide
6.5
6.6
7
7.1
7.2
7.3
7.3.1
7.3.2
7.3.3
7.3.4
7.3.5
7.3.6
7.4
7.4.1
7.4.2
7.5
8
8.1
8.2
8.3
8.4
9
9.1
9.2
9.3
9.4
9.5
9.6
9.7
Ensuring Safe and Successful Control 18
Feedback LEDs 18
Packet Structures 20
Important Information 20
Control Commands (Controller to Device) 20
Status Information (Device to Controller) 20
Bytes 0–1: Control Status 20
Bytes 2–3: Starter State 21
Bytes 4–5: Trip Code 21
Bytes 6–7: Motor Current 22
Bytes 8–9: Motor Temperature 22
Bytes 10–63: Extended Information 22
Parameter Management 24
Output 24
Input 24
Trip Codes 25
Network Design 27
Star Topology 27
Line Topology 27
Ring Topology 28
Combined Topologies 28
Specifications 30
Enclosure 30
Mounting 30
Connections 30
Settings 30
Network 30
Power 30
Certification 30
AN428735951761en-000101/175R11884 | Danfoss A/S © 2022.11
Contents
PROFINET Module
Installation Guide
-
-
-
1 Safety
1.1 Disclaimer
The examples and diagrams in this manual are included solely for illustrative purposes. The information contained in this manual is
subject to change at any time and without prior notice. Responsibility or liability is never accepted for direct, indirect, or consequen-
tial damage resulting from the use or application of this equipment.
1.2 Warnings
WARNING
SHOCK HAZARD
Attaching or removing accessories while the soft starter is connected to mains voltage may cause personal injury.
Before attaching or removing accessories, isolate the soft starter from mains voltage.
WARNING
RISK OF PERSONAL INJURY AND EQUIPMENT DAMAGE
Inserting foreign objects or touching the inside of the soft starter while the expansion port cover is open may endanger person-
nel and can damage the soft starter.
Do not insert foreign objects in the soft starter with the port cover open.
Do not touch the inside of the soft starter with the port cover open.
AN428735951761en-000101 / 175R1188 | 5Danfoss A/S © 2022.11
Safety
PROFINET Module
Installation Guide
•
•
•
-
•
-
-
2 Introduction
2.1 Product Design
The PROFINET Module allows the soft starter to connect to an Ethernet network and be controlled or monitored using an Ethernet
communication model.
Familiarity with Ethernet protocols and networks is required to operate the device successfully. For difficulties arising from using
this device with 3rd-party products, including PLCs, scanners, and commissioning tools, contact the relevant supplier.
2.2 Compatibility
The PROFINET Module is compatible with the following Danfoss soft starters:
MCD 200: 24 V AC/V DC and 110/240 V AC control voltage.
MCD 500: All models.
NOTICE
The PROFINET Module is not suitable for use with MCD 200 soft starters using 380/440 V AC control voltage.
2.3 Product Versions
The PROFINET Module is available in 2 different versions. The part number is printed on the label on the side of the module.
175G9905 MCD PROFINET Module
Monitor and control the soft starter over a PROFINET connection.
175G9915 MCD PROFINET Module
Monitor and control the soft starter over a PROFINET connection.
Monitor and control the soft starter over a TCP connection using VLT® Motion Control Tool MCT 10. Refer to the VLT® Motion
Control Tool MCT 10 Operating Guide.
This installation guide is suitable for use with 175G9915. For the manual for 175G9905, contact the local supplier.
2.4 Network Connection
Table 1: Supported Protocols
Protocols
PROFINET
Industrial Ethernet via PROFINET
TCP
Transmission control protocol to connect to port 4000 of a PC
MQTT
Message queue telemetry transport
OPC UA
Open platform communications unified architecture
AN428735951761en-000101 / 175R11886 | Danfoss A/S © 2022.11
Introduction
PROFINET Module
Installation Guide
4/T2
READY RUN TRIP LOCAL
Exit
Reset
Menu
Store
2/T1 6/T3
1/L1 3/L2
5/L3
VLT
®
Soft Starter
1
2
4
3
5
e77ha805.10
Illustration 1: Overview of Network Connections
1
Soft starter
2
Network switch
3
IoT connection (MQTT/OPC UA)
4
Industrial Ethernet connection to programmable
logic controller
5
TCP connection to VLT® Motion Control Tool MCT
10. Refer to the VLT® Motion Control Tool MCT 10
Operating Guide for connection details.
AN428735951761en-000101 / 175R1188 | 7Danfoss A/S © 2022.11
Introduction
PROFINET Module
Installation Guide
1.
2.
-
3 Installation
3.1 Installing the Communication Module
CAUTION
EQUIPMENT DAMAGE
If mains and control voltage are applied when installing or removing options/accessories, it may damage the equipment.
Remove mains and control voltage from the soft starter before installing or removing options/accessories.
Procedure
Remove control power and mains supply from the soft starter.
Fully pull the top and bottom retaining clips on the module.
e77ha833.10
AN428735951761en-000101 / 175R11888 | Danfoss A/S © 2022.11
Installation
PROFINET Module
Installation Guide
3.
4.
5.
6.
Line up the module with the comms port slot.
e77ha834.10
Push in the top and bottom retaining clips to secure the module to the soft starter.
e77ha835.10
Connect Ethernet Port 1 or Port 2 on the PROFINET Module to the network.
Apply control power to the soft starter.
AN428735951761en-000101 / 175R1188 | 9Danfoss A/S © 2022.11
Installation
PROFINET Module
Installation Guide
4 Connection
4.1 Soft Starter Connection
The PROFINET Module is powered from the soft starter.
NOTICE
The PROFINET Module is not suitable for use with MCD 200 soft starters using 380/440 V AC control voltage.
A1
N2
2
3
1
e77ha620.10
Illustration 2: Connecting MCD 200
1
Soft starter
A1, N2: Stop input
2
PROFINET Module
3
RJ45 Ethernet ports
25
17
18
2
3
1
e77ha621.10
Illustration 3: Connecting MCD 500
1
Soft starter (remote mode)
17, 18: Stop input
25, 18: Reset input
2
PROFINET Module
3
RJ45 Ethernet ports
4.2 Network Connection
4.2.1 Ethernet Ports
The device has 2 Ethernet ports. If only 1 connection is required, either port can be used.
4.2.2 Cables
When connecting to the device, make sure that the cables are of 1 of the following categories:
AN428735951761en-000101 / 175R118810 | Danfoss A/S © 2022.11
Connection
PROFINET Module
Installation Guide
Otros manuales para VLT MCD 200
4
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Controladores de Danfoss
Danfoss
Danfoss ISD Encoder Box Manual de usuario
Danfoss
Danfoss AK-CC55 Manual de usuario
Danfoss
Danfoss VLT HVAC Manual de usuario
Danfoss
Danfoss VLT 5000 Manual de usuario
Danfoss
Danfoss VLT PROFIBUS DP MCA 101 Instrucciones de funcionamiento
Danfoss
Danfoss AFQM 2 Manual de usuario
Danfoss
Danfoss AMEi 6 iSET Manual de usuario
Danfoss
Danfoss FP715Si Manual de usuario
Danfoss
Danfoss ADAP-KOOL AKD 102 Manual de usuario
Danfoss
Danfoss AK-CC 550A Manual de usuario
Danfoss
Danfoss AMV 610 Manual de usuario
Danfoss
Danfoss ECL Comfort 210 Manual de instrucciones de instalación
Danfoss
Danfoss Optyma Plus Manual de usuario
Danfoss
Danfoss VLT Micro Drive Manual de usuario
Danfoss
Danfoss vlt soft starter mcd 500 Manual de usuario
Danfoss
Danfoss VLT Compact Starter MCD 201 Manual de usuario
Danfoss
Danfoss AK-PC 772A Manual de usuario
Danfoss
Danfoss VLT 5000 Manual de usuario
Danfoss
Danfoss VLTAutomationDrive FC 360 Manual de usuario
Danfoss
Danfoss MCO 351 Manual de usuario
