Daktronics Aquatics Guía

DAKTRONICS AQUATICS MAINTENANCE CHECKLIST

DD3691471 072017

201 Daktronics Drive PO Box 5128 Brookings, SD 57006-5128

800-325-8766 605-692-0200 fax 605-697-4700

www.daktronics.com email sales@daktronics.com

Use this checklist to ensure your Daktronics Aquatic Systems is operating properly and looking

as good as possible. We recommend completing these checks every six months, or whenever

you suspect an issue with your display. In most circumstances, the owner or operator of the

display should be able to complete this checklist. For additional information and

troubleshooting resources, see the appropriate manual for your display.

Checklist Task Key Points

OmniSport 2000

oVisually inspect the OmniSport for damage/corrosion. (indicators, switches,

knobs, and connections).

oEnsure keypad buttons are all functional.

oVerify that thermal paper is installed in printer location and

feeds/prints correctly.

oPower up OmniSport console to verify firmware is up to date

(update if needed).

Must be newer than 8.3.27 to update in the field.

oPerform Mock swim race after completing checklist to verify all inputs and

outputs are working (including scoreboard/RTD data).

OmniSport 2000 Manual=ED-13312

On-deck Equipment

(lane modules)

oVisually inspect lane modules for damage/corrosion. (connections,

connector, and cable).

oIf equipment shows signs of corrosion, train customer (if available) proper

cleaning of lane modules using the brass brush (TH-1024/TH-1025) and

silicone grease (LU-1002).

How to Test a Daktronics Lane Module

In-deck Equipment

(deck plates)

oVisually inspect all deck plates for damage/corrosion.

(connections, connector, and cable).

oIf equipment shows signs of corrosion, train customer (if available) proper

cleaning of lane modules using the brass brush (TH-1024/TH-1025) and

silicone grease (LU-1002).

OmniSport 2000 Manual=ED-13312

DAKTRONICS AQUATICS MAINTENANCE CHECKLIST

DD3691471 072017

201 Daktronics Drive PO Box 5128 Brookings, SD 57006-5128

800-325-8766 605-692-0200 fax 605-697-4700

www.daktronics.com email sales@daktronics.com

oTesting:

1. Verify deck plate connections are received into the

OmniSport 2000.

2. Connect the OmniSport 2000 and all cabling to the proper wall plate

in order to receive touchpad and button data.

3. Turn on the OmniSport 2000 and enter swimming mode.

4. The OmniSport should show ( - ) marks across the LCD for the proper

number of lanes.

5. Press MENU > 5 > 2 to go into the testing mode.

6. Test each deck plate by placing a push button into each

touchpad/button connection and pressing the button. TP, B1, B2, B3

will display on the OmniSport 2000 LCD if working correctly.

Horn Start

oVisually inspect horn start and microphone. (indicators, switches, knobs,

cabling, and connections).

oTesting:

1. Test for charger functionality by connecting to the

HS-200. Charging LED should light when plugged in.

2. Ensure microphone is connected to the horn start assembly. Wireless

models, ensure belt pack has a new battery, and matches the wireless

channel set on the HS-200 base assembly, and has the antenna

mounted on the base unit.

3. Set volume controls to desired levels (not min or max) and power up

the HS-200 unit.

4. When the ON-READY LED is on, press the PUSH TO TALK lever

while speaking to ensure audible, then while holding this press small

button on top of the mic at the same time. This will trigger a tone and

a strobe from the HS-200 assembly, while starting the clock on the

OmniSport.

A dual banana (start cable) will need to be ran between

the HS-200 and the OmniSport start circuit to initiate the

start. *OmniSport 2000 Start Input settings much match

connection at the HS-200 (N.O. vs. N.C.).

Lane and/or Aux speakers must be connected to test

each remote speaker/location.

HS-200 Manual=ED-12935

DAKTRONICS AQUATICS MAINTENANCE CHECKLIST

DD3691471 072017

201 Daktronics Drive PO Box 5128 Brookings, SD 57006-5128

800-325-8766 605-692-0200 fax 605-697-4700

www.daktronics.com email sales@daktronics.com

Touchpads

Visually inspect touchpads for dents, scrapes, smudge marks, delamination,

and mounting hardware.

oEnsure edge protectors are surrounding the perimeter of the face

are secure.

oVisually inspect touchpad cart for any damage.

oTesting:

Dry Test

1. While touchpads are on the cart, or laying out on the desk, a

continuity/resistance check can be completed.

2. Connect voltmeter to positive and negative terminal of touchpad

cable and set the meter to resistance/

continuity mode.

3. While sitting idle, the touchpad should register an open

connection, and when pressing on the pad, it should create a

shorted connection.

4. If the pad passes the try test, it can be put in the water to

complete the we test by measuring for DC voltage.

Wet Test 1

1. Place all touchpads into the water and connect to their

lane connections.

2. Turn on the OmniSport 2000 and go into swimming mode.

3. Press MENU > 5 > 2 and go into the test mode.

4. Use your hand or a swimmer to tap the surface of the touchpad

and ensure it registers on the OmniSport. A TP will appear on

the LCD of the OmniSport for the lane being tested.

Wet Test 2

1. Place all touchpads into the water and connect to their lane

connections.

2. Using the voltmeter set to DC voltage, make contact with the

touchpad cable pins (ensure polarity is followed).

3. While sitting idle, the pad should read ~.25 VDC.

4. When a touch is registered, the pad should drop to 0 VDC.

5. Once the touch is released, the pad should return to ~.25 VDC.

*This should take about 5-8 seconds

Touchpad Manual

DAKTRONICS AQUATICS MAINTENANCE CHECKLIST

DD3691471 072017

201 Daktronics Drive PO Box 5128 Brookings, SD 57006-5128

800-325-8766 605-692-0200 fax 605-697-4700

www.daktronics.com email sales@daktronics.com



If this take a long time to recharge, clean the terminals of

the touchpad cable and test again.

Tip: Plug touchpad cable directly into the voltmeter or use

an additional dual banana to test while plugged into the

deck connection.

Relay Take-off

Platform

oVisually inspect the sides, back and front for cracks and/or breaks.

oVisually inspect the gray electronics box for cracks.

oVisually inspect the cable strain reliefs, ensuring they are secure and not

broken, loose, or missing.

oVisually inspect the RTOP cart for any damage.

oTesting:

1. Ensure a new battery (if possible) is installed in the electronics box.

2. Verify the red LED on the electronics box is flashing.

*The RTOP must be plugged into the lane harness and the OmniSport

connected and setup in Swimming mode.

3. Place your hand flat on the RTOP and hold for two seconds.

4. Remove you hand quickly, and the red LED will turn solid for ~1

second then return back to a flashing/ready state.

5. The RTOP time should also be able to be captured on the OmniSport

printout as long as settings/event are configured correctly.

Relay Take-off Platform (RTOP) Manual

Pro Swimming

oVerify software is up to date. *Verify version entitlement; Contact Daktronics

Help Desk if questions arise.

oVerify software opens correctly without errors.

oIf customer has an Ethernet OmniSport it can communicate via network, or

connect (USB/Serial adapter) to Pro Swim laptop and install driver (if

needed).

oConnect standard Ethernet cable from Pro Swim laptop directly to Ethernet

Omni or a network router/switch.

oIf serial, connect cable from J4 EXPANSION PORT on the OmniSport 2000

to the serial cable/adapter on the Pro Swim computer.

oVerify communication between devices. *May need to change com port

value in Pro Swim, or set to UDP.

Detailed Instructions: ED-13876

DAKTRONICS AQUATICS MAINTENANCE CHECKLIST

DD3691471 072017

201 Daktronics Drive PO Box 5128 Brookings, SD 57006-5128

800-325-8766 605-692-0200 fax 605-697-4700

www.daktronics.com email sales@daktronics.com

Pro Diving

oTip: When using serial connections with an Ethernet OmniSport, the network

port must be disabled to allow serial communications.

MENU > 4 > 7 > 7 NETWORK PRO: OFF will allow you to shut off the

Network Pro option.

oVerify software is up to date. *Verify version entitlement; Contact Daktronics

Help Desk if questions arise.

oVerify software opens correctly without errors.

oIf customer has an Ethernet OmniSport it can communicate via network, or

connect (USB/Serial adapter) to Pro Dive laptop and install driver (if

needed).

oConnect standard Ethernet cable from Pro Dive laptop directly to Ethernet

Omni or a network router/switch.

oIf serial, connect cable from J4 EXPANSION PORT on the OmniSport 2000

to the serial cable/adapter on the Pro Dive computer.

oVerify communication between devices. *May need to change com port

value in Pro Dive, or set to UDP.

oTip: When using serial connections with an Ethernet OmniSport, the network

port must be disabled to allow serial communications.

MENU > 4 > 7 > 7 NETWORK PRO: OFF will allow you to shut off the

Network Pro option.

Detailed Instructions: ED-16444

Hy-Tek Meet

Manager

oVerify communication between Hy-Tek and the OmniSport 2000 (via serial

or network). *Ethernet OmniSport 2000s have the ability to do both options.

oFor serial communication to function, the Network MMR feature needs to be

OFF in the OmniSport 2000 menu.

MENU > 4 > 7 > 7 NETWORK MMR: OFF

Ensure that the proper drivers are installed if using a USB-Serial

Adapter, and document the com port being assigned in

Device Manager.

Serial communication uses a straight serial connection to the J6

RESULTS PORT on the OmniSport 2000.

oFor Ethernet Communication to function, the Network MMR feature needs to

be ON in the OmniSport 2000 menu. Connection can be directly between

the two, or go through a switch/router.

Detailed Instructions: ED-13876

DAKTRONICS AQUATICS MAINTENANCE CHECKLIST

DD3691471 072017

201 Daktronics Drive PO Box 5128 Brookings, SD 57006-5128

800-325-8766 605-692-0200 fax 605-697-4700

www.daktronics.com email sales@daktronics.com

Diving Judge

Controls



Using standard Ethernet cable, connect from Hy-Tek computer to the

ETHERNET jack on the back of the OmniSport.

MENU > 4 > 7 > 7 NETWORK MMR: ON

Ensure that the IP address is within range of the OmniSport IP, and

the Subnet and Gateway match.

oOpen Hy-Tek software to configure settings. Start by entering the Run screen

from the top header.

Interfaces > Setup > Timing Console Interface > Daktronics

OmniSport 2000 (Serial or UDP).

Interfaces > Setup > Scoreboard > Daktronics (Serial or UDP).

***Alpha Scoreboard Interface needed for matrix RTD.

oSome setups use Generic Serial for Alternative

configurations (CTS Timer).

oVerify judge console firmware is up to date (3.0 or higher). JC-100 and

RC-100 options.

oVerify base station firmware is up to date if using wireless judge consoles

(3.0 or higher).

oVerify the base station function. Function setting should be set to a 6 on

version 3.0 and higher. (Function 1 for earlier versions).

oVerify the correct 900 MHz antenna is being used on the base station.

oVerify the judge consoles are communicating to the OmniSport 2000.

Detailed Instructions: ED-13312 (Section 7)

Pace Clocks

oVisually inspect space clock (switches, knobs, and connections).

oVerify pace clock firmware is up to date.

oVerify pace clock operation.

After completing the checklist:

Still having issues?

oSearch our Knowledge Base for additional

troubleshooting resources.

oCreate a new service case in your MySupport Account

PC-2001 Manual: ED-13737

PC-2002 Manual: ED-14253

TI-2022 Manual: ED-13736

Tabla de contenidos

Otros manuales de Deporte y aire libre de Daktronics

Daktronics

Daktronics ALL SPORT PRO Manual de usuario

Daktronics

Daktronics BA-1518 Manual de usuario

Daktronics

Daktronics Tuff Sport H-2105 Manual de usuario

Daktronics

Daktronics COLORSMART BB-3146 Manual de usuario

Daktronics

Daktronics DWG-317405 Manual de instrucciones

Daktronics

Daktronics BB-2101 Manual de usuario

Daktronics

Daktronics FB-2600 Series Manual de usuario

Daktronics

Daktronics FB-2700 Series Manual de usuario

Daktronics

Daktronics 3000 Series Manual de usuario

Daktronics

Daktronics BA-515 Manual de usuario

Daktronics

Daktronics MS-2013 Manual de usuario

Daktronics

Daktronics FB-2500 Series Manual de usuario

Daktronics

Daktronics MS-2113 Guía del usuario

Daktronics

Daktronics BB-114 Manual de usuario

Daktronics

Daktronics BB-2101 Manual de usuario

Daktronics

Daktronics Tuff Sport TN-2501 Manual de usuario

Daktronics

Daktronics Tuff Sport BB-2102 Manual de usuario

Daktronics

Daktronics FB-2500 Series Manual de usuario

Daktronics

Daktronics DistaView BA-624-31 Manual de usuario

Daktronics

Daktronics WR-2101 Manual de usuario

Daktronics

Daktronics AR-1522 Manual de usuario

Daktronics

Daktronics FB-2500 Series Manual de usuario

Daktronics

Daktronics BA-2000 Series Manual de usuario

Daktronics

Daktronics FB-2500 Series Manual de usuario

Manuales populares de Deporte y aire libre de otras marcas

Flybar

Flybar POGO TRICK BOARD Manual de usuario

Crivit

Crivit 93713 Manual de usuario

Lifetime

Lifetime POWER LIFT 90865 Manual de usuario

Hudora

Hudora 76171 Instrucciones de montaje

Axler

Axler GSU-1 Manual de usuario

Aquaglide

Aquaglide FREEFALL 6 LANDING PAD Manual de usuario

Cap Strength

Cap Strength POWER RACK FM-CS7000F Manual de usuario

La Sportiva

La Sportiva RACE BORG Manual de usuario

Crivit

Crivit 302640 Manual de usuario

Sportime

Sportime Equalizer Manual de usuario

T&R Sports

T&R Sports 5FT FOOSBALL TABLE Manual de usuario

Salewa

Salewa VERT Manual de usuario

KICK

KICK Decagon Manual de usuario

byox

byox FJ-4.5FT Manual de usuario

CHINESPORT Spa

CHINESPORT Spa 01325 Manual de usuario

AXI.COM

AXI.COM ConesPro101 Manual de usuario

Insportline

Insportline IN 2052 Manual de usuario

Rugged Interactive

Rugged Interactive CardioWall Compact Guía rápida