Dahua Technology ANPR Manual de usuario

ANPR System

Installation Guide

V1.0.0

ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD.

Foreword

General

This installation guide (hereinafter referred to as the "Guide") introduces the structure,

installation, wiring, and commissioning of AI enforcement camera system. It is designed to guide

engineering technicians, contractors, and more for device installation and commissioning

Safety Instructions

The following categorized signal words with defined meaning might appear in the Guide.

Signal Words

Meaning

Indicates a high potential hazard which, if not avoided, will result in

death or serious injury.

Indicates a medium or low potential hazard which, if not avoided,

could result in slight or moderate injury.

CAUTION

Indicates a potential risk which, if not avoided, may result in

property damage, data loss, lower performance, or unpredictable

result.

TIPS

Provides methods to help you solve a problem or save you time.

NOTE

Provides additional information as the emphasis and supplement

to the text.

Revision History

Version

Revision Content

Release Time

V1.0.0

First release.

August 2020

Important Safeguards and Warnings

Operation Requirement

Do not place or install the device in a place exposed to sunlight or near the heat source.

Keep the device away from dampness, dust or soot.

Keep the device installed horizontally on the stable place to prevent it from falling.

Do not drop or splash liquid onto the device, and make sure there is no object filled with

liquid on the Camera to prevent liquid from flowing into the device.

Install the device in a well-ventilated place, and do not block the ventilation of the Camera.

Operate the device within the rated range of power input and output.

Do not dissemble the device.

Transport, use and store the device under the allowed humidity and temperature conditions.

Electrical Safety

Improper battery use might result in fire, explosion, or inflammation.

When replacing battery, make sure the same model is used.

Use the recommended power cables in the region and conform to the rated power

specification.

Use the power adapter provided with the device; otherwise, it might result in people injury

and device damage.

The power source shall conform to the requirement of the Safety Extra Low Voltage (SELV)

standard, and supply power with rated voltage which conforms to Limited power Source

requirement according to IEC60950-1. Please note that the power supply requirement is

subject to the device label.

Connect the device (I-type structure) to the power socket with protective earthing.

The appliance coupler is a disconnection device. When using the coupler, keep the angle

for easy operation.

Maintenance Requirement

Do not try to disassemble the device yourself.

Do not touch charge-coupled device (CCD) or complementary metal oxide semiconductor

(CMOS) directly. Use a blower to remove dust or dirt from the sensor surface.

Use a soft, dry and clean cloth soaked with a small amount of neutral detergent to clean the

Camera.

Declarations

Please read the Guide carefully before installation. Keep the Guide properly for future

reference.

Pay attention to factors such as environmental requirements, application scenarios to avoid

error of system caused by external factors.

Illustrations and descriptions of devices in the Guide are for reference only, and the actual

devices shall prevail.

Devices and software subject to change without further notice.

For latest programs and additional files, please contact our customer service.

III

Construction Safety Instructions

Construction workers must wear protective equipment such as reflective vest to ensure

safety during construction.

Construction sites must be blocked off and placed with signs. Specific requirements are as

follows:

Work on city road: Place in sequence work zone warning sign, work zone speed limit sign,

and traffic guidance sign 150 meters away of coming vehicles from the work zone. In

addition, put work zone safety barriers at reasonable intervals to form a safe work zone and

protect workers’ safety.

Work on expressway: Put work zone warning sign at safe area (such as near hard

shoulder or crash barrier) and 1.5 km away of coming vehicles from the work zone. In

addition, place in sequence work zone speed limit sign, traffic guidance sign, and work zone

distance sign around 150 meters to the work zone. Put work zone safety barriers at

reasonable intervals to form a safe work zone, and place traffic guidance sign at corners of

the work zone. Put sign of canceling work zone speed limit at a safe place 150 meters away

of leaving vehicles from the work zone.

Lifting work or aerial work: The work zone must be placed with clear danger sign and

danger warning light at night. Responsible person should be designated to guide people to

detour. Do not enter or stay in work area.

Aerial work platform: Make sure that its parking position is ideal for aerial work. Check

whether the support legs of aerial work platform are put in place to support the telescopic

boom, and whether heavy-current circuit is connected within the work zone. Make sure the

boom will not touch any object when it is extended.

Workers should fasten safety belt and wear helmet, and properly place equipment, tools

and personal belongings to prevent injuries from falling objects.

Heavy current engineering: During wiring, joint with the heavy current part exposed should

be wrapped with insulated and waterproof tape, which will be put into waterproof insulated

box. When the device is connected to heavy current, make sure the circuit works, and the

insulation cover of cable is inserted into terminal to prevent the insulation cover separating

from the copper wire, resulting in the copper wire exposed. For old wire construction, make

sure no power is connected, and then start construction.

Grounding: Make sure all electric devices are properly grounded during construction.

Table of Contents

Foreword...................................................................................................................................................... I

Important Safeguards and Warnings....................................................................................................... II

Table of Contents......................................................................................................................................IV

1 Device List ............................................................................................................................................... 5

2 System Structure..................................................................................................................................... 6

3 Devices and Accessories....................................................................................................................... 7

Devices ...........................................................................................................................................73.1 3.1.1 AI Enforcement Camera....................................................................................................... 7

3.1.2 Lens...................................................................................................................................... 7

3.1.3 Radar....................................................................................................................................7

3.1.4 Edge Storage Device............................................................................................................9

Accessories....................................................................................................................................113.2 3.2.1 Bracket and Protective Cover..............................................................................................11

3.2.2 Cable...................................................................................................................................12

3.2.3 Traffic Pole..........................................................................................................................12

3.2.4 Outdoor Distribution Board.................................................................................................12

3.2.5Air Switch, Power Surge Protector, Ethernet Surge Protector........................................... 13

3.2.6 Fiber Optical Transceiver and Switch (Optional)................................................................ 13

4 Installation ............................................................................................................................................. 14

Installation Diagram...................................................................................................................... 14

4.1 Installation Notes ..........................................................................................................................154.2 Installing Radar.............................................................................................................................164.3 Installing Edge Storage Device..................................................................................................... 174.4

5 Wiring ..................................................................................................................................................... 19

Wiring Diagram............................................................................................................................. 195.1 Connecting Camera Power Cable................................................................................................195.2 Wiring Radar.................................................................................................................................195.3 Connecting Radar Power Cable................................................................................................... 205.4

6 Commissioning ..................................................................................................................................... 21

Configuring Radar.........................................................................................................................216.1 Commissioning Radar................................................................................................................... 22

6.2 Commissioning Strobe..................................................................................................................236.3

1 Device List

Protective equipment is not included in the list.

The system must be configured with power surge protector and Ethernet surge protector.

The device list in the Guide is for reference only, and the actual devices shall prevail.

Table 1-1 Device list

Device

Material No.

Model

Quantity

Note

AI enforcement

camera

1.0.01.09.12647

DHI-ITC431-RW1

F-L

Models with "-L" are

designed with built-in

white light strobe,

models with "-IR"

supports IR during

night time.

1.0.01.09.12649

DHI-ITC431-RW1

F-IRL8

Universal

mounting

bracket

1.2.01.13.1207

8018

3-dimensional

universal mounting

bracket, needs to be

purchased separately

Bracket

1.1.02.08.11914

PFA150

Mounting bracket,

needs to be purchased

separately

Edge storage

device

1.0.01.09.10329

DHI-ITSE0804-G

N5B-D

1.0.01.09.0237

DH-ITSE0400-GN5A-

B (optional)

Radar detector

1.0.01.09.10282

DHI-ITARD-024S

A-ST

Multi-target

ANPR radar

1.2.01.69.10225

DHI-ITARD-024M

A-H

Signal detector

1.0.01.09.0129

DH-ITASD-012B

2 System Structure

3 Devices and Accessories

Devices3.1

3.1.1 AI Enforcement Camera

AI Enforcement

Camera_User's Manual_20200806.pdf

3.1.2 Lens

Built-in 10.5mm–42mm lens.

3.1.3 Radar

DHI-ITARD-024SA-ST radar

This radar is an integrated traffic auxiliary product with a high degree of intelligence in the field of

intelligent transportation for dynamic detection of moving vehicles.

It can detect vehicles of 1 lane. The radar is featured by high speed detection accuracy

(deviation within ±1km/h), strong anti-interference capability, and high detection rate; low

microwave radiation and power consumption.

DimensionsFigure 3-1

Table 3-1 DHI-ITARD-024SA-ST radar parameters

Parameter

Description

Model

ITARD-024SA-ST

Antenna Type

Microstrip patch array antenna

Radar System

Continuous wave

Microwave

24.125 GHz

Parameter

Description

frequency

Transmit power

20 dBm

Antenna 3dB

beamwidth

6.5°(H) ×5.5°(V)

AD sampling

frequency

25 kHz

Work mode

Forward direction

Number of lane

Single lane

Detection

information

Vehicle speed (instantaneous speed)

Capture rate

≥ 95%

Speed detection

accuracy

±1 km/h

Speed detection

range

3–250 km/h

Snapshot distance

Optimum snapshot distance: 18 m (mounting height: about 6 m)

Communications

interface

Standard RS-232

Cables

Red: 12V+ DC or 24V1 AC. Black: 12 V- DC or 24V2AC. White: Trigger

out. Yellow: RS-232 RXD. Green: RS-232 TXD. Brown: RS-232 GND

Power input

12 V DC and 24 V AC, provides safe and stable power supply with

overvoltage, overcurrent and reverse connection protection.

Interface

protection

Output interfaces are designed with overvoltage and overcurrent

protection.

Working

environment

Temperature: -30 °C to +70 °C

Humidity: 10% to 90%

Dimensions

Radar: 205 × 155 × 65 mm

Bracket: 163.4 × 100 × 155 mm

Weight

1 kg (bracket excluded)

DHI-ITARD-024MA-H Radar

The radar can be installed at any position above the lane to detect vehicles of 1–4 lane(s) within

15–45 m. This radar also sends snapshot trigger signal when a vehicle arrives at designated

position, and detects the lane and the vehicle speed.

Features

One radar can detect up to 32 vehicles from 1–4 lanes.

Precisely detects speed and position of vehicles within 18–35 m.

Flexible installation (front mount or side mount), commissioning through wireless handheld

device, and visual commissioning interface.

Capable of detecting vehicles making U turns or changing lanes.

Detection performance is not influenced by vehicles of adjacent lanes, or vehicles from the

front or back side.

All-weather and all-time.

Detection performance is not influenced by environmental factors such as sunlight, dust,

adverse weather, and temperature.

High capture rate.

99% (smooth traffic), 96% (saturated traffic), 92% (congestion).

Precise positioning.

Positioning accuracy of vehicle capture trigger signal: ±0.5m.

Table 3-2 DHI-ITARD-024MA-H radar parameters

Parameter

Description

Detection distance

15–45 m

Positioning distance

18–35 m

Positioning precision

±0.5 m

Speed detection range

5–350 km/h

Speed detection error

-1.0km/h to 0

Lane width

2–4 m

MU-1 beamwidth coverage

3 m

Microwave frequency

24.15 GHz

Transmission frequency error

< 1 MHz

Frequency modulation bandwidth

250 MHz

Effective isotropic radiated power

(EIRP)

< 20 dBm

Refresh time

50 ms

Communication interface

RS-485/RS-232/Wifi

Baud rate

9600 bps –256000 bps

Radar system

FMCW + Monopulse + Doppler, 3-antenna

Temperature range

-40°C to +85°C

Mounting height

5–10 m

Power supply

12 V DC

Real power consumption

< 3.5 W

Mechanical property

LEXAN housing material, complies with NEMA6 and

IP67

Dimensions

168 ×140 ×50 mm (L ×W ×H)

3.1.4 Edge Storage Device

This Guide uses DH-ITSE0400-GN5A-B edge storage device. This edge storage device can

encode and decode JPEG and H.264 streams. It has 1T capacity by default, and it is designed

with one built-in SATAinterface (supports 2.5-inch HDD) for expanding capacity. The device also

supports ANR (automatic network replenishment), query of pictures and video records, snapshot

and video recording of violations, and more. See Figure 3-2 and Table 3-3.

Tabla de contenidos

Otros manuales de Cámara de seguridad de Dahua Technology

Dahua Technology

Dahua Technology 8A840WANF Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-PFW8601N-H-A180 Manual de usuario

Dahua Technology

Dahua Technology N43AJ52 Manual de usuario

Dahua Technology

Dahua Technology IPC-HFW2431DG-4G Manual de usuario

Dahua Technology

Dahua Technology EOL Series Manual de usuario

Dahua Technology

Dahua Technology IPC-HDW5842T-ZE Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-PFW83242-A180-S2 Manual de usuario

Dahua Technology

Dahua Technology D-SDZ4032-HNR-ZB Manual de usuario

Dahua Technology

Dahua Technology IPC-HFW5449T1-ASE-D2-0360B Manual de usuario

Dahua Technology

Dahua Technology IPC-HDW2431T-AS-S2 Manual de usuario

Dahua Technology

Dahua Technology IPC-HFW3841E-AS-0280B-S2 Manual de usuario

Dahua Technology

Dahua Technology NAVIGATOR X1550 Manual de usuario

Dahua Technology

Dahua Technology IPC-PDW5849-A180-E2-ASTE Manual de usuario

Dahua Technology

Dahua Technology WizMind IPC-PDBW82041-B360 Manual de usuario

Dahua Technology

Dahua Technology DH-PSDW8842ML-A180-D237 Manual de usuario

Dahua Technology

Dahua Technology DH-IPC-HDBW3541FP-AS-M-0280B Manual de usuario

Dahua Technology

Dahua Technology IPC-HFW1320S-W Manual de usuario

Dahua Technology

Dahua Technology IPC-PDB4830-B360 Manual de usuario

Dahua Technology

Dahua Technology IPC-HDW5231R-Z Manual de usuario

Dahua Technology

Dahua Technology D-IPC-HUM8441-E1-L1 Manual de usuario

Dahua Technology

Dahua Technology IPC-HUM4231S-L4-0280B-S3 Manual de usuario

Dahua Technology

Dahua Technology N52BF5Z Manual de usuario

Dahua Technology

Dahua Technology N68BR4 Manual de usuario

Dahua Technology

Dahua Technology IPC-HDW1239DT-PV-STW Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario