D-MAX DMC Series Manual de usuario

USER MANUAL

Full HD (1080P)

EX-SDI/HD-SDI

2Mega Pixel

HD-SDI Camera

The lightning flash with an arrowhead symbol, within an equilateral

triangle is intended to alert the user to the presence of uninsulated

dangerous voltage within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert

the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

INFORMATION - This equipment has been tested and found to comply with limits for a

Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own expense.

WARNING - Changes or modifications not expressly approved by the

manufacturer could void the user’s authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.

Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform

to all local codes

1.Features

---------------------------------

2. Menu Construction

---------------------------------

3. Dimensions & OSD board configurations

---------------------------------

4. Specifications

---------------------------------

Contents

■ 1/3" 2MEGA SONY CMOS

High definition 12-bit digital image signals offering 2 mega pixels

are obtained with high speed of 30 fps and with low power consumption.

■ High Resolution 1100(Color)/(BW) TV Lines

This camera has realized high resolution of 1100(Color)/(BW) TV lines using the top-notch

full digital image processing, 12 Bit A/D serial signal processing and special algorithm

technologies.

■ DNR (Digital Noise Reduction, 2D+3D)

The DNR technology eliminates noise thus generating a distinct and clear image.

This camera DNR function utilizes both an adaptive 2D filter reducing noise in the

brightness of the image and an adaptive 3D filter reducing caused by movement.

■ DAY&NIGHT (Output the Filter changing signal)

This camera has the Day&Night function which outputs the filter changing signal with

detecting the illumination condition.

■ SMART IR

Brightness of IR and saturation phenomenon are automatically adjusted.

■ OSD (On Screen Display)

This camera supports the OSD function which is used with multi language. And so, the

camera can be controlled bye selecting text displayed on the monitor screen.

■ Privacy Mask Function (16 points)

Privacy masking allows for the 'blanking' of specific areas of a scene, where the

viewing or recording of images is prohibited or undesired.

The technology of this camera allows for the user defined setting of a four point

polygonal mask, which is overlaid onto the video signal output.

■ Support both HD-SDI and EX-SDI

This camera can be used HD-SDI mode or EX-SDI mode. The default is HD-SDI mode.

And you can change mode to EX-SDI mode by using OSD button.

■ POC (Power of Coaxial)

This camera support POC function which enables to transfer power of the camera through

coaxial cable.

Features

☞How to change mode from HD-SDI to EX-SDI.

Press “Up”button for 3 seconds and then press “Set”button.

If you want to change HD-SDI mode again, press “Down”button for 3seconds and

then press “Set”button.

All functions would be set by OSD menu.

The menu consists of the main menu and sub menu.

Sub menu is displayed when user press set key on

each menu, at which you see arrow.

Please hold the “SET”key for a while to enter OSD

menu.

1. LENS

Select lens type.

▶DC/MANUAL

2. FOCUS ADJ

Adjust focus status through this menu.

If this menu is on, bars will be displayed on the monitor and adjust bar height as higher.

3. EXPOSURE

This function can adjust the intensity of radiation

incoming to the camera.

Use the "▲" "▼""◀" "▶" "ⓔ" switch or Joystick to

select a menu item.

1) BRIGHTNESS (0~20)

Sets the screen brightness

2) SHUTTER

Select shutter mode.

▶AUTO/INDOOR/FLICKER

- AUTO

The shutter speed will be operated automatically.

▶INDOOR/OUTDOOR/DEBLUR

INDOOR: Iris

OUTDOOR: Iris + Shutter

DEBLUR: SHUTTER: 1/240+AGC

- MANUAL

Select shutter speed from 1/30 to 1/30K

▶1/30(NT:1/30,PAL:1/25),1/60(NT:1/60,PAL:1/50),

1/120(NT:1/120,PAL:1/100),1/250, 1/700, 1/1.6K, 1/2.5K,

1/5K, 1/7K, 1/10K, 1/30K

-FLICKER

This will prevent possible screen distortion to a mismatch between the vertical sync

Menu construction

frequency and the blinking frequency of the lighting.

3) TCS INFO

This function can capture clear image when the object move

fast.

- TCS MODE

Select TCS level

- SPEED: Show the Shutter speed value (1/120 ~ 1/1600)

- DAY/NIGHT: Show the DAY/NIGHT mode (AUTO~EXTERN)

- SMART IR: Show the SMART IR level value

- HLC: Show the HLC on,or off state

4)SENS--UP

Select “Digital Slow Shutter”level (OFF/ 2x, 4x, 8x, 16x, 32x)

5) AGC

Set “Auto gain control”value (1~10)

4. BACKLIGHT

The function is used to set the Back Light Compensation (BLC), High Light Compensation

(HLC) and Wide Dynamic Range (WDR).

▶OFF, WDR, HLC, BLC

1) BLC

BLC Area shows up on the screen

H- POS(0~20):Set the position of BLC area.

V- POS(0~20):Set the position of BLC area.

H- SIZE(0~20):Set the size of BLC area.

V- SIZE0~20): Set the size of BLC area.

OPTION

DESCRIPTION

OFF

MODE1~5

MODE6~10

MODE11~15

MODE16~20

NOT USED

Shutter 1/120~6000 + DN EXT + Smart IR 14

Shutter 1/120~1600+ User DN + User Smart IR

Shutter 1/120~1600 + DN EXT + Smart IR 14 + HLC

Shutter 1/120~1600 + User DN + User Smart IR+ HLC

2) HLC

High Light Compensation

▶ON(0~20), OFF

LEVEL: Select HLC level.

COLOR: Select HLC color(CYN, YEL, WHT, BLK, BLU,

RED, MAG, GRN)

3) WDR

Wide Dynamic Range

WEIGHT:LOW/MIDDL/HIGH

5. DAY/NIGHT

The function is used to set the Day/Night function which switches day/Night mode

automatically based on the level of illumination.

1) AUTO

THRESHOLD(0~20): Sets the threshold for identifying

the Night status from the Day status.

MARGIN(0~20): Sets the margin for identifying the Night

status from the Day status.

DELAY: Sets the Night/Day identification transfer time.

SMART IR (OFF/LOW/MIDDLE/HIGH)

Brightness of IR and saturation phenomenon are automatically adjusted.

2) EXTERN

- EXTERN SW

Select the active level.

- DELAY (1~20)

Set the Night/Day identification transfer time

- SMART IR (1~20)

Brightness of IR and saturation phenomenon are

automatically adjusted.

3) COLOR: Only Color

4) B&W: Only B/W

6. WHITE BAL

This function is used to set the White Balance operation which adjusts the color scheme.

1) AUTO: Auto tracking white balance.

2) MANUAL

White balance value can be changed by “R-GAIN”and “B-GAIN”value in manual mode

3) AUTO ext: TDN lens Auto trace white balance.

It can be changed in AWC mode only.

4) Preset: when the set color temperature doesn’t meet with user’s environment.

7. DNR

Set up 3D-DNR (Digital Noise Reduction) level.

▶OFF, LOW, MIDDLE, HIGH

8. IMAGE

1) SHARPNESS (1~10)

Select the resolution of the camera.

2) GAMMA (0.45,0.55,0.65,0.75)

Select the GAMMA

3) COLOR GAIN (1~20)

Adjusts COLOR GAIN

4) MIRROR (ON/OFF)

Set up the screen mirror

5) FLIP (ON/OFF)

Set up the screen flip

6) D-ZOOM (1X~16X)

Enlarge the screen with DIGITAL ZOOM.

7) ACE (OFF/LOW/MIDDLE/HIGH)

Select Digital ACE(Advanced Enhance) level

8) DEFOG (OFF/MANUAL/AUTO)

This function does a process of clearing blurred image

caused by fog and snow by analyzing the brightness of

input image and compensating the color of the image.

Select defog level.

9) SHARDING

Set the lens shading.

When you maximize zoom ratio and lens angle of view

is saturated on screen, set to ON to make the lens edge

invisible.

It might happen only if fluorescent light is shined fully on

screen.

10) PRIVACY

The function is used to configure up to 16 privacy masks, where the scene is prohibited or

undesired to be viewed.

And you can also make polygon type privacy mask up to 8 areas.

-In case of box type

ZONE NO (0~15): Select 16 areas using left or right

button.

ZONE DISP (ON/OFF): Show up PRIVACY AREA

function on the screen.

H-POS (0~60): H position.

V-POS (0~34): V position.

H-SIZE (0~40): H size.

V-SIZE (0~34): V size.

Y LEVEL(0~20): Adjust the Y LEVEL of the Privacy zone

area

CR LEVEL(0~20): Adjust the B GAIN of the Privacy zone area

CB LEVEL(0~20): Adjust the R GAIN of the Privacy zone area

-In case of polygon type

ZONE NO (0~7): Select 8 areas using left or right button.

ZONE DISP (ON/OFF): Show up PRIVACY AREA

function on the screen.

POS0-X (0~120): H position.

POS0-Y (0~68): V position.

POS1-X(0~120): H size.

POS1-Y(0~68): V size.

POS2-X( 0~120):H position

POS2-Y (0~68):V position.

POS3-X (0~120):H position

POS3-Y (0~68):V position.

Y LEVEL(0~20): Adjust the Y LEVEL of the Privacy

zone area

CR LEVEL(0~20): Adjust the B GAIN of the Privacy

zone area

CB LEVEL(0~20): Adjust the R GAIN of the Privacy zone area

TRANS (0~4): Set the transparency of a color

9. MOTION

The function is used to configure the Motion Detection

operation and Alarm function which sense the

movement of the scene.

DET WINDOW: Press this menu for detail setting.

SENSITIVITY (0~10): Set the motion detection

sensitivity.

MOTION OSD (On/Off): select whether motion area appears or not.

TEXT ALARM (On/Off): select whether motion text appears or not.

WINDOW USE (0~3): Select motion areas you desire to

set.

WINDOW ZONE: Select On or Off

DET H-POS(0~60): H position

DET V-POS(0~34): V position

DET H-SIZE(0~60): H size

DET V-SIZE(0~34): V size

10. OPTION COM

Set camera ID and BAUDRATE for remote control.

This camera supports D-max and Pelco protocol.

In case of box camera can be used this function only.

IMAGE RANGE (Full, Comp, User)

Digital output data scale

FRAME RATE (1080-30p, 720-60p, 720-30p)

Set the frame rate

FREQ

Select input frequency.

COLOR BAR

Select color bar to on or off

CVBS

Select on or off

LANGUAGE

The function is used to select preferred one from the supported languages.

(English/Japanese//Chinese/Korea)

Tabla de contenidos

Otros manuales de Cámara de seguridad de D-MAX

D-MAX

D-MAX 650 TVL Manual de usuario

D-MAX

D-MAX DWC-548DV Manual de usuario

D-MAX

D-MAX DSC-230SI Manual de usuario

D-MAX

D-MAX DWC-540DV Manual de usuario

D-MAX

D-MAX DCC-601DV Manual de usuario

D-MAX

D-MAX DSC-737SE Manual de usuario

D-MAX

D-MAX DCC-500DV Manual de usuario

D-MAX

D-MAX DCC-500D Manual de usuario

D-MAX

D-MAX DCC-520DV Manual de usuario

D-MAX

D-MAX DCC-708DV Manual de usuario

D-MAX

D-MAX DMC-20SEC Manual de usuario

D-MAX

D-MAX DSC-300SE Manual de usuario

D-MAX

D-MAX DCC-600F Manual de usuario

D-MAX

D-MAX DCC-520DV Manual de usuario

D-MAX

D-MAX DCC 600d Series Manual de usuario

D-MAX

D-MAX DCC-520D series Manual de usuario

D-MAX

D-MAX DCC-501DV Manual de usuario

D-MAX

D-MAX DCC-528DV Manual de usuario

D-MAX

D-MAX Superior Speed Dome Manual de funcionamiento

D-MAX

D-MAX DSC-2000Si Manual de usuario

D-MAX

D-MAX DCC-500D Manual de usuario

D-MAX

D-MAX 600 TVL Manual de usuario

D-MAX

D-MAX DCC-580D Series Manual de usuario

D-MAX

D-MAX DCC-500F Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario