D-Link DBA-3621P Manual de usuario

Additional documentation is also available on the D-Link website

DBA-3621P

Quick Installation Guide

Nuclias Cloud-Managed AC1300 Wave 2 Outdoor

Access Point

Label Area

Contents

English 1

DBA-3621P Quick Installation Guide 1

ENGLISH

Hardware Overview

LED Indicators

Label Area

1 2 3 4

Figure 1: LED Indicators

Note: For the LED positions, please unscrew

the protective cap to line up the device with

the diagram above.

# LED Description

1 LAN (PoE)

Green (Solid) - Link preset

Green (Flashing) - Sending or

receiving packets

2 2.4 GHz

Green (Solid) - Device’s 2.4 GHz

band is operating successfully

Green (Flashing) - Sending or

receiving packets

3 5 GHz

Green (Solid) - Device’s 5 GHz

band is operating successfully

Green (Flashing) - Sending or

receiving packets

4Power/

Cloud

Green (Solid) - Device operational

and linked to Nuclias Cloud

Green (Flashing) - Device is trying

to connect to Nuclias Cloud

Orange (Solid) - Device booting

Orange (Flashing) - Device

undergoing reset procedure

Red (Solid) - Device malfunction

Table 1: LED Description

Before You Begin

This installation guide provides instructions

for installing the DBA-3621P on your network.

Additional documentation is also available on

the D-Link support website.

• Nuclias Cloud Manual: For additional

information and instructions on how to

conﬁgure the device using Nuclias Cloud.

Package Contents

This DBA-3621P package includes the following

items:

• DBA-3621P Access Point

• Mounting Plate and Hardware (U-bolts and

nut fasteners, screws and washers)

• Grounding Wire

• Console Cable

• Quick Start Guide

If any of the above items are damaged or

missing, please contact your local D-Link reseller.

Note: To power the unit, use an 802.3af or

802.3at PoE Switch or PoE Injector. This product

is intended to be supplied by a LPS (Limited

Power Source) marked UL Listed Power Unit,

and its output is rated at 48 V DC (PoE), 0.6 A

min., and has a TMA of 60 oC.

System Requirements

• Computers with Windows®, Macintosh®,

or Linux-based operating systems with an

installed Ethernet Adapter.

• Internet Explorer 11, Safari 7, Firefox 28,

or Google Chrome 33 and above (for

conﬁguration).

2DBA-3621P Quick Installation Guide

ENGLISH

Interface Connectors

Label Area

1 2 3

Figure 2: Bottom Connectors

# Connector Description

1LAN(PoE)

Port

Gigabit RJ-45 port for data and

Power over Ethernet (PoE).

2 Reset Press and hold for 10 seconds to

factory reset the device.

3Console

Port

Console port to connect to the

DBA-3621P using a RJ-45 to serial

cable.

Table 2: Interface Description

Label Area

1 2

Figure 3: Rear Connectors

# Connector Description

1Wall/Pole

Mount

Mount to connect to the mounting

plate on a wall or a pole.

2Grounding

Wire

Connector for the grounding wire.

Table 3: Interface Description

Installation

Using Power over Ethernet (PoE)

1. Use a standard Ethernet cable to connect

the LAN1(PoE) port on the DBA-3621P

to a PoE power source device such as

an 802.3af or 802.3at PoE switch or PoE

injector.

Conguration

Using Nuclias Cloud

The DBA-3621P is designed to be managed

through the Nuclias Cloud. Refer to the Nuclias

Cloud Manual for detailed configuration

instructions. To use Nuclias Cloud, your device

must be connected to the Internet.

Note: D-Link recommends manually conﬁguring

the device before mounting it.

Nuclias Cloud App Conguration

1. Download the free Nuclias Cloud app from

the App Store or Google Play by searching

for Nuclias Cloud.

2. Open the Nuclias Cloud app and follow

the onscreen instructions to discover and

set up your device.

Nuclias Cloud Web Conguration

DBA-3621P Quick Installation Guide 3

ENGLISH

1. On an Internet-connected computer,

open a web browser and go to

www.nuclias.com.

2. Enter your D-Link Nuclias username and

password, then click Login.

3. Click on Settings > Add device.

4. Follow the onscreen instructions to set

up your device.

Manual Conguration

Note:The management computer, DHCP server

and DBA-3621P must be in the same subnet.

If you are unable to connect to Nuclias Cloud,

you may need to manually configure the

DBA-3621P using its web user interface. Use

one of the following methods to access the

web user interface:

Connecting through Ethernet

1. Use an Ethernet cable to connect the

DBA-3621P to the management computer,

or to the switch or router the management

computer is connected to.

2. Open a web browser and type in the

default host name of the DBA-3621P in the

address bar and press Enter. The default

host name is DBA-3621P-XXXX where

XXXX represents the last 4 characters

of the MAC address listed on the device

label located on the bottom of the device.

3. Log in to the administration user

interface. The default login information is

Username: admin

Password: admin

Connecting Wirelessly

1. Connect the management computer to

the default SSID of the DBA-3621P. The SSID

will be in the format DBA-3621P-XXXX

where XXXX represents the last 4

characters of the MAC address listed on

the device label located on the bottom

of the device.

2. Open a web browser and type in the

default host name of the DBA-3621P in the

address bar and press Enter. The default

host name is DBA-3621P-XXXX where

XXXX represents the last 4 characters

of the MAC address listed on the device

label located on the bottom of the device.

3. Log in to the administration user

interface. The default login information is

Username: admin

Password: admin

Mounting

Gland Sealing Nut Sealing

Figure 4: LAN Port Waterproof Enclosure

1. Connect an Ethernet Cable to the LAN(PoE)

port on the DBA-3621P. Use the LAN Port

waterproof enclosures to seal the ports.

4DBA-3621P Quick Installation Guide

ENGLISH

Pole Mounting

Figure 5: Attaching the Mounting Base

1. Secure the mount base to the pole using

the U-bolt and the four included nut

fasteners.

Figure 6: Mounting the Device

2. Align and attach the DBA-3621P to the

mounting base using the four included

screws and washers.

Wall Mounting

Figure 7: Attaching the Mounting Plate

1. Align and attach the DBA-3621P to the

mounting plate using the four included

screws and washers.

Figure 8: Mounting the Device

2. Use the mounting plate to mark the

location where to drill the holes in the wall.

3. Drill holes on the markings and place the

included anchors into the drilled holes.

4. Align and place the mounting plate on

top of the anchors and use the included

screws to secure the DBA-3621P to the

wall.

TECHNICAL SUPPORT dlink.com/support

DBA-3621P Quick Installation Guide 5

ENGLISH

Connecting the Grounding Wire

Figure 9: Attaching the Grounding Wire

1. A grounding wire is recommended to

protect your device from lightning strikes

and the buildup of static electricity. Attach

the grounding wire to the DBA-3621P

using the included screw.

Figure 10: Attaching the Grounding Wire

2. Tighten the grounding wire to the

DBA-3621P until it is securely attached.

Figure 11: Attaching the Grounding Wire

3. Attach the other end of the grounding

wire to either the wall or the pole mount.

Ensure that the wall or the pole mount is

connected to an electrical ground.

Appendix - Statements

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

oﬀ and on, the user is encouraged to try to correct the interference by one of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 23.2cm

between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

Country Code selection feature to be disabled for products marketed to the US/CANADA

Professional installation instruction

Please be advised that due to the unique function supplied by this product, the device is

intended for use with our interactive entertainment software and licensed third-party only. The

product will be distributed through controlled distribution channel and installed by trained

professional and will not be sold directly to the general public through retail store.

1. Installation personal

This product is designed for speciﬁc application and needs to be installed by a qualiﬁed

personal who has RF and related rule knowledge. The general user shall not attempt to

install or change the setting.

2. Installation location

The product shall be installed at a location where the radiating antenna can be kept

23.2cm from nearby person in normal operation condition to meet regulatory RF exposure

requirement.

3. External antenna

Use only the antennas which have been approved by the applicant. The non-approved

antenna(s) may produce unwanted spurious or excessive RF transmitting power which may

lead to the violation of FCC limit and is prohibited.

4. Installation procedure

Please refer to user’s manual for the detail.

5. Warning

Please carefully select the installation position and make sure that the ﬁnal output power

does not exceed the limit set force in relevant rules. The violation of the rule could lead to

serious federal penalty.

Industry Canada statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the

following two conditions:

(1) This device may not cause interference; and (2) This device must accept any interference,

including interference that may cause undesired operation of the device.

Cet appareil est conforme aux CNR exemptes de licence d’Industrie Canada. Son fonctionnement

est soumis aux deux conditions suivantes:

(1) Ce dispositif ne peut causer d’interférences; et(2) Ce dispositif doit accepter toute interférence,

y compris les interférences qui peuvent causer un mauvais fonctionnement de l’appareil.

Caution:

(i) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725

MHz shall comply with the e.i.r.p. limit; and

(ii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply

with the e.i.r.p. limits speciﬁed for point-to-point and non point-to-point operation as appropriate.

(iii) Users should also be advised that high-power radars are allocated as primary users (i.e. priority

users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause

interference and/or damage to LE-LAN devices.

Avertissement:

(i) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5

470-5 725 MHz doit se conformer à la limite de p.i.r.e.;

(ii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit

se conformer à la limite de p.i.r.e. spéciﬁée pour l’exploitation point à point et non point à point,

selon le cas.

(iii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute

puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5

250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des

dommages aux dispositifs LAN-EL.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 26.6cm

between the radiator & your body.

Déclaration d’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de

26.6 cm de distance entre la source de rayonnement et votre corps.

Professional installation instruction

1. Installation personal

This product is designed for speciﬁc application and needs to be installed by a qualiﬁed

personal who has RF and related rule knowledge. The general user shall not attempt to

install or change the setting.

2. Installation location

The product shall be installed at a location where the radiating antenna can be kept

26.6cm from nearby person in normal operation condition to meet regulatory RF exposure

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de D-Link

D-Link

D-Link AMPLIFI DAP-1525 Manual de usuario

D-Link

D-Link AirPremier N DAP- 2590 Manual de usuario

D-Link

D-Link AirPlus DWL-900AP Manual de usuario

D-Link

D-Link DWL-3260AP - AirPremier - Wireless Access... Manual de usuario

D-Link

D-Link DWR-923 Manual de usuario

D-Link

D-Link DWL-3500AP Manual de usuario

D-Link

D-Link DWL-8720AP Manual de usuario

D-Link

D-Link DWL-1000AP Manual de usuario

D-Link

D-Link DAP-2590 - AirPremier N Dual Band PoE Access... Manual de usuario

D-Link

D-Link D DWL-8200AP DWL-8200AP Manual de usuario

D-Link

D-Link DWL-G700AP - AirPlus G Access Point Manual de usuario

D-Link

D-Link DAP-1150 Manual de usuario

D-Link

D-Link DWL-8610AP Manual de usuario

D-Link

D-Link D DWL-8200AP DWL-8200AP Manual de usuario

D-Link

D-Link DWL-3610AP Manual de usuario

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

D-Link

D-Link AirPremier N DAP-2690 Manual de usuario

D-Link

D-Link DAP-3666 Manual de usuario

D-Link

D-Link DAP-2330 v 1.0 Manual de usuario

D-Link

D-Link DAP-3666 Manual de usuario

D-Link

D-Link DAP-3315 Manual de usuario

D-Link

D-Link DAP-1155 Manual de usuario

D-Link

D-Link DAP-2620 Manual de usuario

D-Link

D-Link AirPlus DWL-900AP+ Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario

EnGenius

EnGenius EAP350 Manual de usuario