D-Link XStack DGS-3610 Series Manual de usuario

DGS-3610 Series

Quick Installation Guide

Version 1.1

Product Overview

The DGS-3610 series is a new generation of 10G multi-layer chassis switch developed by D-Link that

features high performance, high-security, intelligence and ease of use. The DGS-3610 switch provides

flexible media interfaces, which accommodate various media for connection in networking. In addition,

this series can be flexibly expanded with various 10G modules to offer high expandability and meet the

needs for large bandwidth. The hardware of this series supports multi-layer wire-speed switching and

provides a full range of perfect routing protocols to meet the requirement for multi-routing and high

performance of large-scale networks.

The DGS-3610 provides the intelligent service flow classification from layer 2 to layer 7, perfect QoS and

multicast application management feature. While providing high performance and intelligence, this series

features excellent internal safety protection and user management, which effectively prevent and control

virus spreading and network attacks, prevent illegal users from accessing the network, and ensure that

legal users can reasonably use network resources. This guarantees the safe and reasonable use and

operation of the network. Additionally, this series allow diversified safe control policies to be implemented

according to the actual network environments.

The DGS-3610 switches provide large network convergence and medium-sized network cores with

multi-layer switching, perfect end-to-end QoS, flexible and rich security settings and policy-based NM, at

a high performance-price-ratio, best meeting the requirements of enterprise networks for high speed,

security, and intelligence.

Currently, DGS-3610 series covers three types so as to meet kinds of application of users:

DGS-3610-26: 24 10/100/1000M adaptive RJ45 ports, multiplexing 12 1000M SFP

ports. Two back extended 10G ports.

DGS-3610-26G: 24 1000M SFP ports, multiplexing 12 10/100/1000M adaptive RJ45

ports. Two back extended 10G ports.

DGS-3610-50P: 48 10/100/1000M RJ45 ports, 4 combo 1000M SFP ports, and 2 10G

extension slots.

Applications:

Convergence layers of large networks or the backbones of medium-sized networks;

Upgrade to the 10G uplink backbone network by simply adding 10G modules for

protecting user investment;

Scenarios where numerous 1000M ports are needed to provide high-performance data

processing;

High-performance multi-layer switching solutions;

Rich security management mechanism to offer network security protection,

high-security access control and effective network access control;

Perfect use of management policies to help the management of bandwidth and ensure

the application of key services such as voice, multicast audio/video service and VOD

Prior Preparation

This switch is already prepared for installation at delivery. Before connecting the power supply and the

network, please check all the accessories against the packing list in the packaging carton.

Warning

Read the installation instructions carefully before you power on the

system.

Caution

Do not place the switch close to water or in a damp place. Prevent

moisture from entering the switch.

Keep the switch away from the places with much dust or strong

electromagnetic interference.

Desktop Mounting

Step 1

Attach the four adhesive rubber pads provided in the carton onto the

indentations on the four corners at the bottom of the switch.

Step 2

Place the switch on the desktop flatly to ensure that the air around the switch

can flow freely.

You can install the handles onto the switch as shown below:

Figure 1-1 Schematic Diagram for Installing the Handle

The above figure shows the schematic diagram for installing the handle on the switch. There are eight

screw holes on the handle. Align the handle with the screw holes on the side wall of the switch and

tighten the sunk screws.

Warning

To prevent overheating of the switch, place the switch in a location where

the ambient temperature is no more than 40°C. Also the spacing of at least

10cm should be reserved around the chassis for good ventilation.

Caution

Do not place any heavy objects on the switch.

Rack Mounting

You can also mount the switch in the wiring section of a standard 19-inch rack. First fasten the

accessories for rack mounting from the carton onto both sides of the switch and then mount the switch

into the 19-inch rack with screws. When you are doing this, you can use the attached two L-shaped

handle fastening brackets and M3*10FMO sunk screws.

Step

Keep the fastening brackets with handles closely onto both sides of the

switch, align with the screw holes and fasten them with M3*10FMO sunk

screws, as shown in the following diagram:

Figure 1-2 Schematic Diagram for Installing the L-Shaped Fastening Bracket

Step

Fasten the switch onto the rack, as shown in the following diagram. You

should prepare the screws needed for rack mounting by yourself.

Figure 1-3 Schematic Diagram for Fastening the Switch

Caution

Please ensure that the ventilation holes and fans on both sides and at the

back of the chassis are not blocked.

System Connection

1.1.2 Connecting the RJ-45 Port

Use shielded or unshielded twisted pair cables with RJ-45 connectors on both ends. Use cables of

Category 3, 4, and 5 to connect the 10Mbps Ethernet, and use cables of Category 5 to connect the

100/1000Mbps Ethernet ports. Connect one end of a cable to the network card or the RJ-45 port of

another switch/HUB, and the other end to the RJ-45 port of the switch. When you plug the RJ-45

connector, you should hear a “click”, which means that the connector is plugged tightly.

Warning

Do not insert a phone connector into the RJ-45 port, as this may damage

the switch.

Caution

Ensure that each twisted pair cable does not exceed 100 m in length.

1.1.3 Connecting Optical Fibers

Connect the optical module on the switch by using an optical fiber whose connector matches that of the

optical module. When you are doing this, connect the RX end of one party to the TX end of the other

party to ensure correct Rx/Tx channel connection.

Warning

Do not stare into the 1000BASE-SX/LX ports as invisible laser radiation

from them may hurt your eyes.

1.1.4 Laser Safety

Most optical transceiver modules supported by the DGS-3610 series are Class I laser products.

Therefore, pay attention to the following during your use of this product:

Do not stare into the optical module Tx ends or the connected fiber jumpers, as invisible

laser radiation from them may hurt your eyes.

Unused optical modules should have their jumper ports covered with dust plugs, as dust

may pollute or damage the laser connectors.

Danger

Never stare into the optical module Tx ends and the connected fiber

jumpers to avoid injuries to your eyes.

Connecting Power Cables to the Switch

Please carefully read the following warning statements before you connect the power supply to the

switch.

Warning

The first time you connect the power supply, please ensure that the power

supply matches the power requirements of the switch to avoid damaging

the switch.

Caution

You must use the 3-pin power socket with a ground end, and the distance

between the power socket and the switch should be no more than 1.8 m.

For more reliable grounding, ground the grounding terminal at the rear

panel of the switch.

To do this, perform the following steps:

Step 1

Connect the grounding hole at the back of the switch to the grounding system of

the equipment room.

Step 2

Connect the power supply of the switch.

Step 3

Check the “Status” LED on the front panel. If it is flashing, the power supply is

normal and the switch starts initialization.

Optional Installation Procedure

This section describes the procedure that may be useful to you, depending on your on-site needs and

how you configure your switch. If you want to configure the switch via the CLI, you must first connect the

Console port of the switch to the computer. The cables needed for such connection are provided with the

switch. The computer must be installed with a particular type of terminal simulation software (for example,

WINDOWS HyperTerminal). Set the following parameters for the software: 9600 for baud rate, 8 data bits,

no parity check, 1 stop bit, and no flow control. For details of how to configure the switch via CLI, see the

CLI section in the configuration guide.

Otros manuales para xStack DGS-3610 Series

Tabla de contenidos

Otros manuales de Enrutador de red de D-Link

D-Link

D-Link DIR-865L Manual de usuario

D-Link

D-Link DIR-822-US Manual de usuario

D-Link

D-Link Express Ethernetwork DI-704P Manual de usuario

D-Link

D-Link DSL-2500U Manual de usuario

D-Link

D-Link DSL-3785 Instrucciones de funcionamiento y mantenimiento

D-Link

D-Link DIR-859 Manual de usuario

D-Link

D-Link DIR- 809 Manual de usuario

D-Link

D-Link DIR-826L Manual de usuario

D-Link

D-Link DWR-932C Manual de usuario

D-Link

D-Link DIR-514 Manual de usuario

D-Link

D-Link DIR-868L Manual de usuario

D-Link

D-Link EXO DIR-2660 Manual de usuario

D-Link

D-Link EXO AX COVR-X1870 Manual de usuario

D-Link

D-Link DES-2108 Manual de usuario

D-Link

D-Link DIR-600 Manual de usuario

D-Link

D-Link DSL-G2562DG Manual de usuario

D-Link

D-Link DES-3624 - Switch - Stackable Manual de usuario

D-Link

D-Link DSL-2650U Manual de usuario

D-Link

D-Link DWR-920 Manual de usuario

D-Link

D-Link DFL-300 - Security Appliance Manual de usuario

D-Link

D-Link Express Ethernetwork DI-707P Manual de usuario

D-Link

D-Link DES-1016 Manual de usuario

D-Link

D-Link DIS-300G Series Manual de usuario

D-Link

D-Link DIR-821 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad

D-Link xStack DGS-3610 Series Manual de usuario

Manuales populares de Enrutador de red de otras marcas